8mm epp laser instruction manual specifications wingspan : 31.5in (800mm) length : 31.1 in (790mm) wing area : 226sq in (14.6sq dm) flying weight : approx. 8oz (225-240g).
Www.Valuehobby.Com/8mm-epp-laser.Html 2 dear customer, congratulations on your purchase of elite models laser 8mm epp airplane arf from value hobby. We thank you for your generous support, and hope you enjoy your new airplane. At value hobby, we hope to offer competitive prices, good performance, an...
Www.Valuehobby.Com/8mm-epp-laser.Html 3 safety in flying this is not a toy! It is a very high-performance rc airplane capable of high speeds and extreme maneuvers. It should only be operated by a competent pilot in a safe area with proper supervision. Only fly your aircraft in a safe, open area, awa...
Www.Valuehobby.Com/8mm-epp-laser.Html 4 main parts: 1. Vertical fuselage x 1 2. Horizontal fuselage x 1 3. Wing panel x 2 4. Tail x 1.
Www.Valuehobby.Com/8mm-epp-laser.Html 5 accessories: list: 1. Fiberglass parts including motor mount x 2, control horn x 4, elevator control horn x 1, wheel x 2, landing gear mounting plate x1, aileron servo arm extension x 1, rudder servo arm extension x 1, elevator servo arm extension x 1, pushrod...
Www.Valuehobby.Com/8mm-epp-laser.Html 6 recommended radio equipment product sku quantity radio flysky fs-i6 transmitter and receiver set fly-rc-4572 1 servo towerpro sg90 9g servo twp-sv -0352 3 3s power setup product sku motor gforce 2206-1500kv brushless outrunner motor vhb-mt-3530 esc hobbywing f...
Section 1: airframe assembly step1. As shown in the picture, place the fuselage on a work surface, and glue the wings to the fuselage. Step2. Put some foam glue into the spar slot. Step3. Press 650mm wing spar into the slot and use weights to keep it in position until the glue cures. Step4. Glue two...
Www.Valuehobby.Com/8mm-epp-laser.Html 8 step8. Use a hobby knife to cut a slight slot for control horn on the marked location. Step9. Glue the control horn into the slot. Step10. Glue the rudder servo into the fuselage. Step11. Slide the horizontal fuselage into the vertical fuselage. Align the tabs...
Www.Valuehobby.Com/8mm-epp-laser.Html 9 step14. As shown, prepare three assembled servo arms. Step15. Install the servo arm onto the servo. Step16. Use a square and foam glue to glue the vertical fuselage and horizontal fuselage pieces together. Start at the front and slowly work your way toward the...
Www.Valuehobby.Com/8mm-epp-laser.Html 10 step19. Glue two side wings on to the main wing. Section 2: servos linkage installation step1. Use a hobby knife to cut a slight slot for the rudder control horn on the rudder. Step2. Glue the control into the slot. Step3. Insert the guides into the horizonta...
Www.Valuehobby.Com/8mm-epp-laser.Html 11 step4. Insert the guides into the vertical fuselage for the rudder servo pushrod. Step5. Slide two pushrods into the guides. Step6. Attach the z-bend to the elevator horn. Step7. Slide a shrink tubing to the pushrod wire. Use a soldering iron to shrink the tu...
Www.Valuehobby.Com/8mm-epp-laser.Html 12 step10. Use the same method to install the rudder servo linkage. Step11. Install the aileron servo linkage using the same method. Section 3: motor installation step1. Glue the motor mount to the fuselage. Step2. Install a 2206 motor to the motor mount step3. ...
Www.Valuehobby.Com/8mm-epp-laser.Html 13 section 4: landing gear installation step1. Glue the rectangle part into the slot on the fuselage. Step2. Glue two 210mm rods into the fuselage as shown. Step3. Use thin ca to quick glue the two round parts into the landing gear wires. Then use foam glue to g...
Www.Valuehobby.Com/8mm-epp-laser.Html 14 2015-07-08.
