- DL manuals
- Vanco
- Switch
- EVMX4444
- Manual
Vanco EVMX4444 Manual
Summary of EVMX4444
Page 1
Vanco part number evmx4444 hdmi® 4x4 matrix selector switch www.Vanco1.Com • 800.626.6445 hdmi® 4x4 matrix selector switch.
Page 2: Www.Vanco1.Com
Www.Vanco1.Com 800.626.6445 2 1. Do not expose this unit to water, moisture, or excessive humidity. 2. Do not install or place this unit in a built-in cabinet, or other confined space without adequate ventilation. 3. To prevent risk of electrical shock or fire hazard, due to overheating do not obstr...
Page 3: Www.Vanco1.Com
Www.Vanco1.Com 800.626.6445 3 introduction the evolution by vanco evmx4444 hdmi 4x4 matrix selector switch allows 4 hdmi sources to be distributed to up to 4 displays simultaneously. Have multiple sources displayed simultaneously on any display or have a single source duplicated on multiple displays...
Page 4: Www.Vanco1.Com
Www.Vanco1.Com 800.626.6445 4 specifications technical specs hdcp compliance ...................................................... Yes video bandwidth ........................................................ Single-link 225mhz [6.75 gbps] video support .................................................
Page 5: Www.Vanco1.Com
Www.Vanco1.Com 800.626.6445 5 1. Power switch: 2. Port 1-4: input source channels mapping led for each output channel 3. Port 1-4 select: push button for selecting input channels 4. Source status: input source indicator led 5. Ir sensor: ir sensor for receiving the ir commands from ir remote 6. Led:...
Page 6: Www.Vanco1.Com
Www.Vanco1.Com 800.626.6445 6 edid the edid switch allows for edid learning or to pre-set an edid to encourage a “handshake” between the display and source. The edid learning function is only necessary whenever any display on the hdmi output port is not outputting audio and video properly. Because t...
Page 7: Www.Vanco1.Com
Www.Vanco1.Com 800.626.6445 7 operation control - ir remote control 1. Input/output switch - push the corresponding button on the remote to select input & output port. Ex: select input 2 to output 3 - the button highlighted in the red circle button shown below to select input 2 to output 3 2. Functi...
Page 8: Www.Vanco1.Com
Www.Vanco1.Com 800.626.6445 8.
Page 9: Www.Vanco1.Com
Www.Vanco1.Com 800.626.6445 9 1. System requirement 1) os information: ms winxp/7 2) baud rates: 9600 3) software size: 3 mb 4) minimum ram requirement: 256 mb operation control – software control through rs-232 operation control - software control through rs-232 and ethernet port 1. I/o routing but...
Page 10: Www.Vanco1.Com
Www.Vanco1.Com 800.626.6445 10 1. I/o routing button i/o: select the input click “send” to change the i/o setting save mapping: select mapping(1-8) click “save” button to save current mapping preset mapping: select mapping(1-8) click “recall” button to recall previous mapping which are saved.
Page 11: Www.Vanco1.Com
Www.Vanco1.Com 800.626.6445 11 2. Rename i/o button rename i/o: rename output name rename input name rename mapping: rename mapping name.
Page 12: Www.Vanco1.Com
Www.Vanco1.Com 800.626.6445 12 3. Edid button learn edid from default select default edid(1-8 default edid) select input click “send” button to learn default edid learn edid from display select output select input click “send” button to learn display edid load edid file to input select input click “...
Page 13: Www.Vanco1.Com
Www.Vanco1.Com 800.626.6445 13 4. Network save setting save the ip address which is manually entered read setting: read the ip address from the device ** the default ip address is 192.168.1.111.
Page 14: Www.Vanco1.Com
Www.Vanco1.Com 800.626.6445 14 5. System button firmware update version: to get the f/w version information factory reset.
Page 15: Www.Vanco1.Com
Www.Vanco1.Com 800.626.6445 15 6. Com port selection click “ ” button to select com port 7. Connection status connected status: connecting status: disconnected status: 8. Connect/disconnect click this button “ ” to change connection status.
Page 16: Www.Vanco1.Com
Www.Vanco1.Com 800.626.6445 16 click “ ” button to switch to ethernet function if ethernet is connected, the button will show the sign image to let you know. 9. Rs-232 10. Ethernet click “ ” button to switch to rs-232 function. If rs-232 is connected, the button will show the sign image to let you k...
Page 17: Www.Vanco1.Com
Www.Vanco1.Com 800.626.6445 17 connection diagram connect and operate 1. Connect up to 4 sources such as a blu-ray player, game console, a/v receiver, cable or satellite receiver, etc. To the hdmi inputs on the unit. 2. Connect the output hdmi ports, starting with ouput 1, to high-definition display...
Page 18: Www.Vanco1.Com
Www.Vanco1.Com 800.626.6445 18 ir pass-through ir blaster tx ir receiver rx ir blaster (ev-irtx) plug ir blaster into ir tx port of matrix unit (evmx4444); place blaster in front of the ir eye of the corresponding source. Ir receiver (ev-irrx) plug ir receiver into ir rx port of matrix unit (evmx444...
Page 19: Www.Vanco1.Com
Www.Vanco1.Com 800.626.6445 19 notice 1. Vanco high speed hdmi cables are strongly recommended for use with this product to ensure best results. 2. Incorrect placement of ir blaster and receiver may result in the failure of the unit. Please check carefully before plugging in the ir accessories into ...
Page 20: Www.Vanco1.Com
Www.Vanco1.Com 800.626.6445 20 trouble-shooting 1. Best results are usually achieved when the source and display resolutions are the same. If resolutions differ, the extenders will try to adjust the signal to match the resolution of the hdtv with the lowest resolution. This will result in a picture ...
Page 21: Www.Vanco1.Com
Www.Vanco1.Com 800.626.6445 21 safety and notice the evmx4444 has been tested for conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic equipments, the evmx4444 should be used with care. Please read and follow the safety instru...
Page 22: Www.Vanco1.Com
Www.Vanco1.Com 800.626.6445 22 limited warranty with the exceptions noted in the next paragraph, vanco warrants to the original purchaser that the equipment it manufactures or sells will be free from defects in materials and workmanship for a period of two years from the date of purchase. Should thi...
Page 23: Www.Vanco1.Com
Www.Vanco1.Com 800.626.6445 23 liability statement every effort has been made to ensure that this product is free of defects. The manufacturer of this product cannot be held liable for the use of this hardware or any direct or indirect consequential damages arising from its use. It is the responsibi...
Page 24
Vanco ® international 506 kingsland drive batavia, illinois 60510 call: 800.626.6445 fax: 630.879.9189 visit: www.Vanco1.Com.