1. DL manuals
  2. Vantec
  3. PCI Card
  4. UGT-IS100R
  5. User Manual

Vantec UGT-IS100R User Manual

Summary of UGT-IS100R

  • Page 1

    4+1 sata ii 300 ide/pata pci-e combo host card w/ raid & port multiplier user manual model: ugt-is100r all brand names and trademarks are properties of their respective owners. W w w . V a n t e c u s a . C o m.

  • Page 2: Table of Contents

    Ugt-is100r page 2 table of contents 1. Features and benefits ......................... 3 2. Bus interface ........................................ 3 3. Ports ...................................................... 3 4. System requirements ......................... 4 5. Package contents .................

  • Page 3: Features and Benefits

    Ugt-is100r page 3 features and benefits z compliant with one-lane 2.5gb/s pci express specification z compliant with serial ata 1.0 specification z supports serial ata generation 2 transfer rate of 3.0gb/s z supports native command queue (ncq) on sata ports z supports hot plug z provides three indep...

  • Page 4: System Requirements

    Ugt-is100r page 4 system requirements z pci express-enabled system with one available pci express slot z windows® 2000, xp/2003/vista/2008/7 (32/64 bit) package contents z 1 x 4+1 sata ii 300 ide/pata pci-e combo host card w/ raid & port multiplier z 1 x driver cd z 1 x user’s manual z 2 x sata data...

  • Page 5: Jumper Settings

    Default, port con1 & con2 are working. Ugt-is100r page 5 jumper settings jp description active port 1-2 close enable sata port con1 j1-j4 2-3 close enable sata port.

  • Page 6: Con3

    Ugt-is100r page 6 con3 1-2 close enable sata port con2 j5-j8 2-3 close enable sata port con4 hardware installation 1. Turn off the power to your computer. 2. Unplug the power cord and remove your computer’s cover. 3. Remove the slot bracket from an available pci-e slot. 4. To install the bard, caref...

  • Page 7: Raid Arrays

    Ugt-is100r page 7 raid arrays raid arrays are setup in the 4+1 sata ii 300 ide/pata pci-e combo host card w/ raid & port multiplier ’s bios. There are four configurations supported: raid level/type configurations number of disks needed raid 0 disk striping 2 or 3 or 4 raid 1 disk mirroring 2 raid 0+...

  • Page 8: Enter.

    Ugt-is100r page 8 “space” key to mark the selected disk, then press enter. 6. Please use arrow keys ↑ and ↓ to select chunk size from 4k, 8k, 16k, 32k, 64k or 128k, then press enter. 7. Input the raid size, press enter. 8. When asked created raid on the select hdd (y/n)?, press y to accept. 9. At th...

  • Page 9: Y To Accept.

    Ugt-is100r page 9 7. When asked created raid on the select hdd (y/n)?, press y to accept. 8. At the next screen select save and exit setup, press enter. When asked save to disk &exit (y/n)?, press y to exit the bios. Concatenation (jbod) 1. As the bios boots press ctrl+j when prompted to enter the r...

  • Page 10: Enter.

    Ugt-is100r page 10 exit the bios. Raid 0+1 (striping + mirroring) 1. As the bios boots press ctrl+j when prompted to enter the raid bios. 2. At the next screen select create raid disk drive, press enter. 3. Enter raid name, press enter. 4. Please use arrow keys ↑ and ↓toswitch the raid level to 01-s...

  • Page 11: Delete Raid Disk Drive

    Ugt-is100r page 11 delete raid disk drive 1. As the bios boots press ctrl+j when prompted to enter the raid bios. 2. At the next screen select delete raid disk drive, press enter. 3. Please use arrow keys ↑ and ↓toselect the array you want to delete, use the “space” key to mark the selected array, t...

  • Page 12: Rebuild Mirror Drive

    Ugt-is100r page 12 connection information, will be written to the replacement disk. Rebuild mirror drive when a failure to one member occurs, you will be notified by the raid bios during boot. The steps below will guide you in rebuilding a failed mirror set. 1. Replace the failed drive(s) with one o...

  • Page 13: Driver Installation

    Ugt-is100r page 13 f up. During this (post) process, the bios will show up and indicate the devices attached to it. Driver installation for windows® 2000, xp and server 2003 or a new installation a new installation requires a floppy disk for the driver installation. To make this floppy disk, copy th...

  • Page 14: Start, Then Run.

    Ugt-is100r page 14 on-screen instructions to complete the windows installation. For an existing installation 1. Setup the raid array prior to driver installation and boot up to windows. 2. Please insert the cd driver bound with 4+1 sata ii 300 ide/pata pci-e combo host card w/ raid & port multiplier...

  • Page 15: F6 To Install The Driver.

    Ugt-is100r page 15 directions below. 1. Setup the raid array prior to windows installation. 2. Follow microsoft’s windows installation procedure. 3. At the windows setup screen, press f6 to install the driver. 4. When prompted, press s to specify the location of the driver. 5. Insert the floppy disk...

  • Page 16: For Windows® Vista

    Ugt-is100r page 16 f installation. 6. Restart windows to complete the installation. For windows® vista or a new installation a new installation requires a floppy disk for the driver installation. To make this floppy disk, copy the contents of the“ ugt-is100r\2000_xp_2003_vista\floppy32 ” folder, fou...

  • Page 17: Start, Then Run.

    Ugt-is100r page 17 f 1. Setup the raid array prior to driver installation and boot up to windows. 2. Please insert the cd driver bound with 4+1 sata ii 300 ide/pata pci-e combo host card w/ raid & port multiplier into your cd-rom drive. 3. At the windows desktop, click start, then run. 4. Type d:\ u...

  • Page 18: Load Driver To Install

    Ugt-is100r page 18 f 3. At the windows setup screen, press load driver to install the raid driver. 4. Insert the floppy disk, please select jmicron jmb36x controller (a:\jraid_f.Inf), then press next. (change a:\ to match your floppy drive letter) 5. Follow the on-screen instructions to complete the...

  • Page 19: For New Installation

    For windows® server 2008/7 (32-bit) for new installation 1. Setup the raid array prior to windows installation. 2. Follow microsoft’s windows installation procedure. 3. At the windows setup screen, press load driver to install the raid driver. 4. Please insert the cd driver bound with 4+1 sata ii 30...

  • Page 20: Start, Then Run.

    Ugt-is100r page 20 f into your cd-rom drive. 3. At the windows desktop, click start, then run. 4. Type d:\ ugt-is100r\2000_xp_2003_vista\setup.Exe , click ok. (change d:\ to match your cd-rom drive letter) 5. Follow the on-screen instructions to complete the installation. 6. Restart windows to compl...

  • Page 21: Start, Then Run.

    7. Follow the on-screen instructions to complete the installation. Ugt-is100r page 21 for an existing installation 1. Setup the raid array prior to driver installation and boot up to windows. 2. Please insert the cd driver bound with 4+1 sata ii 300 ide/pata pci-e combo host card w/ raid & port mult...

  • Page 22: Controller:

    Ugt-is100r page 22 controller: -jmicron jmb36x controller should be displayed windows® vista: double click storage controllers: -jmicron jmb36x controller should be displayed.