1. DL manuals
  2. Vantex
  3. Toy
  4. AL504
  5. Instruction Manual

Vantex AL504 Instruction Manual

Manual is about: 88'' 50CC

Summary of AL504

  • Page 1

    Picture may not be the same as actual product. Please refer to actual product. We reserve the rights of updating product information, appearance and parameters without notice. Instruction manual specifications: wingspan: 2235mm (88 in) length: 1947mm (76.7 in) wing area: 94.5dm2 (1464.8 sq in) flyin...

  • Page 2

    21 table of contents appendix – parts and options.

  • Page 3

    This is a sophisticated hobby product and not a toy. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not i...

  • Page 4

    This warranty does not cover cosmetic damage or damage due to acts of god, accident, misuse, abuse, negligence, commercial use, or modification of or to any part of the product. This warranty does not cover damage due to improper installation, operation, or maintenance. This warranty is limited to t...

  • Page 5

    18 3 radio equipment recommended engines • 4-channel radio system (minimum) • 1 standard servo for throttle • 5 hi-torque servos • d-55, q-50 • propeller (consult engine instructions) • servo extensions • y-harness adhesives • 6-minute epoxy • 30-minute epoxy • thick ca glue • threadlock additional ...

  • Page 6

    4 required parts step 1 • wing panel ( right ) locate the opening for the aileron servo at the bottom of the aileron. Carefully remove the covering from the opening using a hobby knife. Left and step 2 plug a servo extension onto the servo. Tie the servo leads together by using a secure connector, o...

  • Page 7

    5 required parts step 1 • wing panel (left and right) • aileron (left and right) tape the aileron to the wing. Using a square held in alignment with the outer hole in the servo arm and 90 with the trailing edge of the wing, mark the aileron with a pen where the straight edge intersects the aileron h...

  • Page 8

    Step 5 from the top of the aileron, plug the control horn screw through the hole and secure it with the provided nut. Step 6 repeat steps 1 through 5 for the remaining aileron. Required parts step 1 • wing panel ( right ) • aileron (left and right) properly hinging the control surfaces on this model...

  • Page 9

    Step 3 step 4 hint: remove the screws and wick thin ca into the holes to strengthen the threads. Then, reinstall the screws. Step 5 remove the bracket and drill pilot holes at the previously marked positions. Assemble the tail wheel bracket and use provided screws to secure the bracket in place. A h...

  • Page 10

    13 required parts step 1 step 2 • fuselage • rudder • tail wheel assembly install the tiller arm to the bottom of the rudder with screws. Position the tail wheel in place as shown, centered on the rear of the fuselage. Using a felt-tipped pen, mark the positions for the mounting screws through the t...

  • Page 11

    12 step 2 step 3 install the rudder servo on the right position of servo tray in the fuselage. Attach the servo arm to the servo. Make sure the servo arm is perpendicular (90 ) to the centerline of the fuselage when the servo is at the neutral position. Put the fuselage on its side with rudder virtu...

  • Page 12

    10 from the top of the elevator, plug the control horn screw through the hole and secure it with the provided nut. Step 6 step 7 cut off the first section of one of the hinges. This is done to clear the tube installed in the stabilizer. Step 8 glue the elevator hinges in place using the same techniq...