VAPamore MR-500 Vento Instruction Book - page 4
USING YOUR MR-500 VENTO
Fig. 12
GO TO VAPAMORE.COM TO SEE THE MR-500 VENTO INSTRUCTIONAL VIDEO
contact Vapamore service at 480-951-8900. Fig. 12
ELECTRIC FLOOR HEAD
Fig. 13
Fig. 14
Fig. 15
Fig. 16
upright/stored and operating. When in the upright/stored
position the handle is locked into place. To lower the
handle to the operating position, push the handle release
pedal. Fig. 13
depending on the surface being cleaned. If cleaning rugs
or carpet turn on the rotating brush. If cleaning hard
vacuum on. Fig. 15
Always check to make sure the rotating brush is clear and
free of any pet hair or debris. Remove and clean any built
up debris from the rotating brush. Also make sure the
Note: The rotating brush uses a special designed drive
belt. In the case that the drive belt should break due to
over stress or a brush jam, contact Vapamore for service at
480-951-8900 or visit vapamore.com to order a
replacement drive belt.
Handle
release
petal
Reset button
RESET
RESET
HEIGHT
Carpet
height
adjuster
Carpet height indicator
petal
Keep intake
and brush
clear of
debris
The carpet height adjuster has a range of 1-6 and is
adjusted in according to the surface being cleaned.
Always adjust going up (1 up to 6) until you reach the
desired setting. When adjusting down (6 down to 1)
the adjuster is designed to skip numbers to return to
1 faster. Adjust by depressing the foot pedal located
Fig. 17
NON ELECTRIC FLOOR HEAD & TOOLS
Your MR-500 Vento comes with a variety of non electric
tools used for more detailed jobs. These tools include a
long reach crevice tool, small crevice tool and a detail brush
tool. All these attachments can be used with the non
electric extension pole or direct to the hose handle. Fig. 17
USING YOUR MR-500 VENTO
GO TO VAPAMORE.COM TO SEE THE MR-500 VENTO INSTRUCTIONAL VIDEO
Fig. 18
. jet no
HARD SURFACE FLOOR HEAD
extension pole and is for use on hardwood, stone,
(Store this tool in the mesh storage bag.)
SMALL DETAIL FLOOR HEAD
brush and is great for tight areas, stairs, auto interior and
furniture. This tool can be used with the non electric
extension pole or direct to the hose handle. Fig. 17
(Store this tool in the mesh storage bag.
MIN
MA
X
Hard surface
floor head
and non
electric
extension
pole
Use with
non electric
extension
poll or hose
handle
Hose handle
Non electric
pole
SMALL CREVICE TOOL & DETAIL BRUSH TOOL
The small crevice tool and a detail brush tool are stored in
the vacuum located under the tool lid. Push the tool lid
release latch to open the tool lid. Fig. 19-20 The small detail
brush separates by snapping off and removing the brush
section to make a flat surface tool.
The small crevice tool and a detail brush tool are great for
smaller jobs and hard to reach areas such as furniture,
under appliances, vents and screens, auto, boat and RV’s.
These tools can be used with the non electric extension
pole or direct to the hose handle. Fig. 17
LONG REACH CREVICE TOOL
Fig. 19
Fig. 20
Fig. 21
Tool lid release latch
Small
crevice
tool
Deatil
brush
tool
Long reach crevice tool
Fig. 22
Set vacuum
on end when
cleaning stairs
USING ON STAIRS
When using to clean stairs, place the vacuum on end and
.
The long reach crevice tool is great for hard to reach areas
such as between furniture cushions, under appliances, air
duct vents, auto, boat and RV’s. This tool can be used with
the non electric extension pole or direct to the hose handle.
Fig. 21 (Store this tool in the mesh storage bag.)
Use with the non electric extension
pole or direct with the hose handle