Quick start guide english.
What’s included » [ 1 ] pro 3 battery » [ 1 ] pro 3 atomizer (2.0ohm) » [ 1 ] pro 3 tank (w/ pre-installed 2.0ohm atomizer » [ 1 ] micro usb cord » [ 1 ] pack of o-rings (4) note: included in the kit are two mini replacement o-rings for the drip tip and two larger o-rings for pro 3 tank..
Pro 3 tank atomizer head priming when getting ready to use the provided 2.0ohm atomizer, it is important that you prime the atomizer to avoid a burnt hit. This is an important cost saving measure. Unscrew the bottom cap of the tank from the tank’s body and remove the atomizer by pulling it from the ...
Tank fill process after priming the atomizer, unscrew the top cap of your tank, take your liquid and proceed to pour along the sidewalls of the center air pipe. After filling the tank, screw the top cap back onto the body of the tank. Using short breaths, inhale from the drip tip up to 5 times and a...
Bottom cap of tank top cap of tank drip tip tank atomizer.
To turn on the pro 3 battery, click the power button 5 times continuously. You will do the same in order to turn the device off as well. If the device does not turn on, you must use the usb cord (included) to charge the device. Note: please let the battery fully charge for best results. Powering the...
Note: if you hold the button for more than 7 seconds, the output will shut off automatically and the button light will blink 10 times. Pass-through the pro 3 allows for you to vape while the device is charging using the provided usb cord. Note: while it is possible to continue use during charging, i...
Power button battery tank drip tip.
Guia de inicio espaÑol.
¿quÉ viene incluido? » [ 1 ] batería pro 3 » [ 1 ] atomizador pro 3 (2.0 ohm) » [ 1 ] tanque pro 3 (con atomizador preinstalado de 2,0 ohm) » [ 1 ] cable usb micro » [ 1 ] paquete de juntas tóricas nota : en el kit se incluyen dos mini juntas tóricas de remplazo para la punta de goteo y dos juntas t...
Pro 3 tanque cebado de la cabeza del atomizador cuando esté pronto para utilizar el atomizador de 2,0 ohm provisto, es importante cebar el atomizador para evitar una pitada quemada. Se trata de una medida importante de ahorro. Desenrosque la tapa de la parte inferior del tanque del cuerpo del tanque...
Proceso de llenado del tanque luego de cebar el atomizador desenrosque la tapa superior de su tanque, tome su líquido y viértalo a lo largo de las paredes del tubo de aire central. Después de llenar el tanque, atornille la tapa en el cuerpo del tanque. Con respiraciones cortas, inhale desde la punta...
Tapa del tanque inferior tapa del tanque superior punta de goteo tanque atomizador.
Pro 3 bateria para encender la batería del pro 3, haga clic en el botón de encendido 5 veces continuamente. Es necesario hacer lo mismo para apagar el dispositivo. Si el dispositivo no se enciende, debe utilizar el cable usb (incluido) para cargar el dispositivo. Encendido del dispositivo nota: por ...
En el botón de encendido 5 veces para encender la batería. Sostenga el botón de encendido mientras que inhala desde la punta de goteo y luego suelte el botón de encendido, una vez que logre la producción de vapor deseada. Nota: si presiona el botón durante más de 7 segundos, la salida se apagará aut...
BotÓn de encendido bateria tanque punta de goteo.
Vaporfi.Com.