1. DL manuals
  2. Vari
  3. Lawn and Garden Equipment
  4. Hurricane F-530
  5. Instructions For Use Manual

Vari Hurricane F-530 Instructions For Use Manual

Manual is about: Mulcher

Summary of Hurricane F-530

  • Page 1

    Mulcher hurricane f-530 instructions for use 2007.

  • Page 2

    Hurricane f-530 with leading wheel 2 contents 1 basic information. ..............................................................................................................3 2 foreword..................................................................................................................

  • Page 3

    Hurricane f-530 with leading wheel 3 1 basic information. ask your dealer to provide the machine unpackaging and the briefing. Fill in the following data concerning your machine. The data are important for ordering spare parts. It is advised to have a copy of this page with all data on the machine...

  • Page 4

    Hurricane f-530 with leading wheel 4 2 foreword. Dear customer and user! Thank you for trusting our products. You have become owner of machine from a wide range of machines and attachments made by ,a.S. As a system of gardening, farming, small agricultural and communal machinery. The mulcher hurrica...

  • Page 5

    Hurricane f-530 with leading wheel 5 3 operation safety. 3.1 safety regulations. this international symbol indicates important messages concerning safety. When you see the symbol, be aware of a possible injury threatening to you or to other persons and read the attached instructions carefully. t...

  • Page 6

    Hurricane f-530 with leading wheel 6 when the machine is in operation, all other persons (children in particular) and animals have to be outside the machine’s working space. The machine operator can continue working only after they have been shown out to a safe distance (see pictograph 6). Note: t...

  • Page 7

    Hurricane f-530 with leading wheel 7 note: the pictures of the self-adhesive labels with the pictographs in the right part of the table correspond with their position as seen from the operator’s site. 1. 2. 228 4203 75 3. 4. 5. 6. 7. 8. 4 use, technical specifications and technical description of th...

  • Page 8

    Hurricane f-530 with leading wheel 8 are dry and the cutting blades are capable of crushing them into small pieces which need not be removed from the surface. The maximum recommended height of swards emerged in the same period when cut is up to 40 cm. This maximum height may decrease according to sw...

  • Page 9

    Hurricane f-530 with leading wheel 9 5 instructions for use. 5.1 machine assembly. Ask your dealer to provide unpackaging of the machine and briefing in machine operation. Grip points for unpacking from the box: blade cover in the front, “u” tube of the machine frame at the back. If you assemble the...

  • Page 10

    Hurricane f-530 with leading wheel 10 5.2 putting into operation. the machine may be delivered without engine fillings (in dependence on different national regulations)! first thoroughly read the instruction for engine use! You can prevent a possible damage to the engine. 1. Check oil volume in ...

  • Page 11

    Hurricane f-530 with leading wheel 11 starting of the cutting blade is accompanied with a partial v-belt slippage and with the accompanying phenomena such as whistling, rattling, etc. The phenomenon usually disappears after the belt has started properly moving. 4. After the cutting blade starts turn...

  • Page 12

    Hurricane f-530 with leading wheel 12 5.5 machine stop. If you wish to stop the machine travel, release the lever on the left handlebar grip. The machine will stop moving but the blade will still turn. The cutting blade drive will be switched off after release of the lever on the right handlebar gri...

  • Page 13

    Hurricane f-530 with leading wheel 13 might damage the machine. If these cannot be removed, avoid working in such places. working width has to be at all times accommodated to stand density! if possible, do not use the machine on wet grass. Remember that the terrain you are moving on must always ...

  • Page 14

    Hurricane f-530 with leading wheel 14 shoe position for lower height of the stubble, approx. 5 cm. Always work with an assistant when changing the slide shoe position. 1. Secure the machine against self-motion (by wedging) on a solid surface or a pad 2. Lift the front part of the machine, so that th...

  • Page 15

    Hurricane f-530 with leading wheel 15 be very careful while lifting the machine and driving back! B) engine losing rotations and stalling: release both levers on the handlebars, lift the machine front by pushing down on handrails and move the machine slightly back. Clean the space under the cuttin...

  • Page 16

    Hurricane f-530 with leading wheel 16 excessive wear. The exchange interval can be extended up to 130 hours with oils of higher grades (api gl – 5, sae 80w – 90). The running-up period of 5 hours must be observed. Czech oils fully meeting the requirements are „mogul trans 90“ or „mogul trans 80w-90“...

  • Page 17

    Hurricane f-530 with leading wheel 17 figure 6: lubrication points figure 6.1: swivel lever of the clutch figure 6.2: tightening pulley arm pin and blade brake pin figure 6.3.: leading wheel 6.2 tightening of bolted connections. Regularly check the tightening of the bolted connections. Always check ...

  • Page 18

    Hurricane f-530 with leading wheel 18 central m10x1x25 bolt has a fine thread and therefore it must not be confused with outer bolts whose threads are normal! D) tighten the bolts at a prescribed tightening moment (see chapter 7.2 ). should there be excessive vibrations on the machine handlebars...

  • Page 19

    Hurricane f-530 with leading wheel 19 d) take the old v-belt off and replace it with a new one. Original v-belt marking is optibelt x13x1335 ld 6t6k, ord. No. 184 608. It is also possible to use an equivalent v-belt made by other manufacturers at a size of a13x1300 li (li=internal length) or a53“ (5...

  • Page 20

    Hurricane f-530 with leading wheel 20 figure 10: bowden cables and adjustment bolts 6.5 adjusting the wires of pulley, brake and wheel drive clutch. In order to guarantee low operating forces on levers which control the drive switching, it is advisable to lubricate the wires in bowden cables at leas...

  • Page 21

    Hurricane f-530 with leading wheel 21 6.6 diagnostics of driving problems. 6.7 table of service operations. Operation during season after season gearbox oil check 1x monthly yes,* engine oil check prior to any other use ** engine air filter check prior to any other use ** blade check for clamping an...

  • Page 22

    Hurricane f-530 with leading wheel 22 6.8 washing and cleaning of the machine. cleaning and washing the machine, proceed to observe valid regulations and legislation on the protection of watercourses and other water resources against pollution or contamination with chemical substances. never was...

  • Page 23

    Hurricane f-530 with leading wheel 23 6.9 machine storage. Prior to any longer storage, clean the machine from all dirt and plant residues. Repair damaged paint on machine parts. For any long-time storage of the machine it is advisable: a) to conserve the cutting blade b) to drain petrol out of the ...

  • Page 24

    Hurricane f-530 with leading wheel 24.

  • Page 25

    Hurricane f-530 with leading wheel 25 blade drive pos. Part name dimensions drawing - standard ord. No. Pcs 100 chassis of mulcher f-530 weldment 22 9 1536 060 184 111 1 101 102 brake shoe 22 9 1664 024 189 014 2 103 driven pulley 22 9 3325 012 189 004 1 104 pulley assembly separate part list 1 105 ...

  • Page 26

    Hurricane f-530 with leading wheel 26.

  • Page 27

    Hurricane f-530 with leading wheel 27 wheel drive pos. Part name dimensions drawing - standard ord. No. Pcs 200 engine plate 22 9 8032 050 196 008 1 201 riveted mudflap 22 9 8534 010 196 059 1 202 handlebars assembly separate part list 1 203 driven part of clutch 32 0 3625 029b 196 045 1 204 gearbox...

  • Page 28

    Hurricane f-530 with leading wheel 28 pos. 323, 324 and 325 to be mounted after the v-belt (pos. 309) is put on.

  • Page 29

    Hurricane f-530 with leading wheel 29 engine and covers pos. Part name dimensions drawing - standard ord. No. Pcs 300 driving pulley diam. 106 dw assembly 22 9 3325 034 184 022 1 301 mulcher v-belt cover assembly 22 9 8545 039 184 020 1 302 front cover weldment 22 9 8549 012 182 030 1 303 key 3/16” ...

  • Page 30

    Hurricane f-530 with leading wheel 30

  • Page 31

    Hurricane f-530 with leading wheel 31 handlebars pos. Part name dimensions drawing - standard ord. No. Pcs 1 welded handlebars 22 9 8078 059 196 002 1 2 control lever 32 0 8058 009 196 013 2 3 4 bowden cable of clutch 622 9 8074 044 196 515 1 5 bowden cable of roller 622 9 8074 045 196 516 1 6 bowde...

  • Page 32

    Hurricane f-530 with leading wheel 32.

  • Page 33

    Hurricane f-530 with leading wheel 33 gearbox pos. Part name dimensions drawing - standard ord. No. Pcs 1 fork weldment 22 1 3330 013a 189 078 1 2 lever assembly 22 9 3330 017 196 022 1 3 driving disc assembly 22 9 3616 006 189 029 1 4 worm 2:54 32 0 3214 028 196 023 1 5 worm wheel 32 0 3221 016 196...

  • Page 34

    Hurricane f-530 with leading wheel 34 pulley assembly pos. Part name dimensions drawing - standard ord. No. Pcs 1 pulley arm 32 0 3330 034 196 010 1 2 pulley bearing shell 32 0 9320 071 196 528 1 3 pulley 632 0 3325 040 189 586 1 4 bearing 6300 2rs Čsn 024630 189 585 1 5 retaining ring 35 Čsn 02 293...

  • Page 35

    Hurricane f-530 with leading wheel 35 leading wheel pos. Part name dimensions drawing - standard ord. No. Pcs 1 leading wheel frame f-530 (2006) 22 9 1646 042 184 116 1 2 wheel hinge f-530 (2006) 22 9 1646 040 184 117 1 3 distance ring 32 0 9320 094 184 118 1 4 sliding washer 32 0 9220 229 182 039 1...

  • Page 36

    Hurricane f-530 with leading wheel 36 10 letter of guarantee. To be completed by manufacturer name of product mulcher model hurricane f-530 serial number …………………………………………………………………………. Engine serial number …………………………………………………………………………. Warranty (months) …………………………………24………………..……………………... Output contr...

  • Page 37

    Hurricane f-530 with leading wheel 37 warranty inspection 1 date: ………………………………………person in charge:………………………………………………… service shop stamp and signature warranty inspection 1 machine model………………………… serial no.:…………………………… warranty inspection 2 date:………………………………………person in charge:………………………………………………… s...