Summary of V-AM500D
Page 1
V-am500d class d mono amplifier d instruction manual.
Page 2: V-Am500D
V-am500d 2 thank you for buying our mono amplifier v-am500d! Please read attentively this instruction manual providing information on features and exploitation of this unit. Features high speed mosfet power supply high hardness double side circuit board fully adjustable low pass crossover short circ...
Page 3: V-Am500D
V-am500d 3 the location chosen should provide at least 2" of clearance above the amplifier for adequate ventilation. If the amplifier is to be mounted vertically be sure that it is in a place where adequate air will flow along the length of its heatsink fins for cooling. Never mount the amplifier up...
Page 4: V-Am500D
V-am500d 4 installation mounting: 1. After reading safeguard notes, decide where you are going to install the unit. 2. Once the location has been determined, place the amplifier into position. Using a felt tip pen or pencil mark the four holes to be drilled for mounting. Never use the amplifier as a...
Page 5: V-Am500D
V-am500d 5 connections power connections it is important to have good quality power and ground connections. Remember, to complete an electrical circuit, the ground connection is just as important as the positive power connection. Before any power connections are made, disconnect the ground cable at ...
Page 6: V-Am500D
V-am500d 6 speaker connections the minimum impedance is 1 ohm. Connect the speaker wire to corresponding speaker output terminals of the amplifier. Be sure to have the positive wire from the speaker connected to the positive speaker terminal of the amplifier and the negative wire from the speaker co...
Page 7: V-Am500D
V-am500d 7 connection method 2 fig. 4. All of the controls can be adjusted only in “master” mode amplifier. Lowest recommended impedance is 2 hm mono. Rca inputs are connected to both left and right channels. Gain control is to be set to match input source..
Page 8: V-Am500D
V-am500d 8 adjustments fig.5. 1. This amplifier is used to drive a subwoofer. The frequencies above the crossover point will be attenuated at 12db/octave. Low pass filter (lpf) permits to adjust the crossover frequency by rotating the knob using a flat head screw driver to select any frequency betwe...
Page 9: V-Am500D
V-am500d 9 3. S.S.F - subsonic filter allows you to block (filter) ultra-low frequencies that your subs cannot reproduce. The level of crossover frequency can be changed from 10 hz to 50 hz by rotating the knob. The frequencies below the crossover point will be attenuated at 12db/octave. 4. The bass...
Page 10: V-Am500D
V-am500d 10 trouble shooting guide before you consult this listing, make sure the vehicle’s electrical system is working properly by verifying that other electrical items (e.G. Headlights, windows, etc.) still function correctly. Symptom probable cause solution low or n.C. Remote turn-on connections...
Page 11: V-Am500D
V-am500d 11 specification model v-am500d @ 14.4 volts, 4 ohm 1 x 500 watts @ 14.4 volts, 2 ohm 1 x 700 watts rms power @ 14.4 volts, 1 ohm 1 x 1000 watts low pass filter 30 hz – 250 hz maximum output power 1200 w frequency response (-1db) 10 hz –250 hz subsonic filter 10 hz – 50 hz signal to noise r...
Page 12: V-Am500D
V-am500d 12 v-am500d! , – . 4 ga 0/180° rca , , . , , . , . , . 5 . , ..
Page 13: V-Am500D
V-am500d 13 , . . , , . , , , , . ( ) , 13.3 2 . . 0,5 . ; , . , , , . , , ; . ( , ). , , . ( , .), , . , . , , , . , . , 12 « ». , , . . ( ), , , +12 . , , . ( 100 ) . 130 . !.
Page 14: V-Am500D
V-am500d 14 1. , . 2. . , . 3. 4 3,5 3,0 – . 4. . 5. ( .1). . 1.
Page 15: V-Am500D
V-am500d 15 . 13.3 2 , . «gnd» . . : , . . ( ) . , , . , . . «remote» «remote amplifier» . , , . « +» , 0,5 . . . . 2.
Page 16: V-Am500D
V-am500d 16 1 . , . , ( ) ( . .3). 1 .3..
Page 17: V-Am500D
V-am500d 17 2 . 4. , «master». 2 . Rca . ..
Page 18: V-Am500D
V-am500d 18 .5. 1. . 30 – 250 , lpf. 12 . 2. , . 6 - 200 . , «6 ». Cd, ¾ ( «0,2 »). , . , 3/4 - . , , . Input line out l ch r ch master 0 min 0db 30hz 250hz.
Page 19: V-Am500D
V-am500d 19 3. S.S.F - ( ). , . 10 – 50 , . 12 . 4. «bass eq» 0 18 45 . 5. Slave/master slave: «slave» . Master: «master» . 6. – . . , ( 0 o 180 o ). . ( ) . ..
Page 20: V-Am500D
V-am500d 20 . . . . . . , , , . . . , . . ( , ). . , rca . Rca ; ; , ..
Page 21: V-Am500D
V-am500d 21 v-am500d 14,4 (4 ) 1 x 500 14,4 (2 ) 1 x 700 rms 14,4 (1 ) 1 x 1000 30 – 250 1200 (-1 ) 10 – 250 10 – 50 (‘a’ wtd) >92 200 - 6 10 (0~18 ) 45 ( – ) 12 40 a x 3 ( ), 330 155 50 ..