- DL manuals
- VarTech Systems
- Monitor
- VT181M2
- User Manual
VarTech Systems VT181M2 User Manual
Summary of VT181M2
Page 1
Color tft lcd monitor vt181r2 · vt181rh2 · vt181m2 user’s guide read these instructions completely before attempting to operate your new color display. Vartech systems inc. Solutions for demanding applications industrial crt and flat panel displays.
Page 2: Table of Contents
Table of contents page page section 1 section 4 introduction 1 troubleshooting tips 10 1.1 about lcd monitors 1 1.2 product safety precautions 2 section 5 cleaning & maintenance 11 section 2 display setup 3 section 6 2.1 instructions 3 mechanical drawings 12 2.2 repacking 3 18.1” low scan tabletop m...
Page 3: Introduction
Lcds introduction introduction 1 section about lcd monitors what you gain by using an lcd monitor in your industrial controls are the future of display technology. Crts although they have dropped in cost significantly, do not offer the performance, reliability, and mounting options available with lc...
Page 4: Product Safety Precautions
Product safety precautions ⇒ ensure that sufficient space is available around the display to provide the circulation necessary for cooling. ⇒ ensure that the ambient air temperature will not exceed the specified maximum temperature. ⇒ do not attempt to service this display yourself. The rear chassis...
Page 5: Display Setup
Installation do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a sink, in a wet location where there is standing water. Displays are provided with ventilation opening...
Page 6
R.G.B.H.V. Bnc inputs for analog signals these inputs allow monitor to be used with bnc connector leads with 3 wire operation (sync on green) 4 wire operation (composite syncs) 5 wire operation (separate h,v syncs) r,g,b inputs have 75Ω input resistance. H,v inputs must be ttl level inputs. Signal c...
Page 7: ↑
Operating instructions the monitor must be connected to a suitable dc power source and video signal. The monitor will switch on as soon as the power is applied and a picture will be displayed. Basic user controls adjustments to the picture can be made by means of the push button controls on the fron...
Page 8
Procedure for picture adjustment each value that is adjusted is automatically saved when the highlighted line is moved, the only exception is when the restore function is used. If at any time the monitor cannot accept the new settings it will recall the previous good values. 6 step 1 move picture so...
Page 9
Other osd functions restore use this function if adjustments mad to monitor need to be undone. This returns the monitor to the state when the osd was started. Use the ↑ & ↓ buttons until restore is highlighted. Then use the → & ← buttons to undo adjustments made to the monitor. Reset mode(s) this ha...
Page 10
8 frequency & frequency fine adjustment of tft monitors the video signal is made up of pixels. These are generated in the video generator (process controller, pc, etc.) a crystal oscillator controls the rate at which the pixels are generated: this is called the dot clock. When the tft monitor receiv...
Page 11
Resolution v rate h rate syncs application 640 x 350 70hz 31.475khz h v vga 640 x 400 70hz 31.475khz vga 640 x 480 60hz 31.475khz vga 1024 x 384 40hz 16.67khz iecc railway signaling 1024 x 768 60hz 48.40khz xga 1280 x 1024 60hz 63.98khz sxga 640 x 384 50hz 20.65khz abb mod300 640 x 384 60hz 24.78khz...
Page 12: Troubleshooting Guide
Troubleshooting guide troubleshooting guide 4 section 10 trouble troubleshooting tip unable to set vertical size the vertical size value is limited by what values are set for frequency and horizontal size. Not all video modes can be shown full screen. Sometimes the vertical size will have to be smal...
Page 13: Cleaning And Maintanence
11 cleaning and maintanence cleaning and maintanence cleaning occasionally clean the display panel and cabinet with a soft cloth dampened (not soaked) with a mild (non-abrasive) glass cleaner. Keep turning a fresh side of the cloth toward the screen surface to avoid scratching it with accumulated gr...
Page 14: Mounting Instructions
Mounting instructions mounting instructions 6 section mechanical drawings model description page(s) vt181m2 18.1” low scan tabletop mechanical drawing 13 vt181r2 18.1” low scan rack mount mechanical drawing 14 vt181rh2 18.1” honeywell configured rack mount mechanical drawing 15 12.
Page 15: Specifications
16 input voltage: 90-264vac universal power consumption: 60w max display area 14.135” x 11.310” 359.02mm x 287.27mm pixel format 1280 x 1024 signal formats 640 x 480 pixels, 800 x 600 pixels, 1024 x 768 pixels,1280 x 1024 pixels abb mod 300 horizontal scan 15-70khz vertical scan 56-75hz clock rate 1...
Page 16
150-026-005 7.16.03 vartech systems headquarters 11529 sun belt ct. Baton rouge, louisiana 70809 toll-free: 800.223.8050 international phone: 001.225.298.0300 fax: 225.297.2440 e-mail: sales@vartechsystems.Com www.Vartechsystems.Com.