DL manuals Varytec Flood Light Easymove XL 60 Spot User Manual Varytec Easymove XL 60 Spot User Manual - page 6 Other manuals for Easymove XL 60 Spot: User Manual 123456789 Page of 9 Go Download Print this page Bookmark us 6 / 9 button to select the menu function currently displayed, or to enable a menu option. To return to the previous option or menu without changing the value, press the button. No alterative worth that return re-option or menu , press(MENU)button 4.2. Menu Map RPON set up the dmx address A001 – A512 AU01 fast speed movement AU02 slow automatic movement SNOF Sound to Light OFF SNON Sound to Light ON RPOF TILT and Pan are non inverted RPON invert PAN RTON invert Tilt RTOF invert the display RDOF non invert the display DFON default settings Note ! the factory settings are DMX address A001 and every function is non inverted. 4.3. User configuration Setup automatic moving mode(self-motion move) .Press the MENU until it shows AU01 .Use the UP/DOWN buttons to set to AU01 or AU02 , Press ENTER to confirm. Sound to light moving mode(sound control) .Press the Mode button until it shows SNOF . .Use the UP/DOWN buttons to set to SNON, press ENTER to confirm. Master/slave mode(auto-running 、sound control) This mode will allow you to link up 32 units together without a controller. Use standard DMX cables to daisy chain your fixtures together via the DMX connector on the rear of the units. Proper performance it may be necessary to use a terminator at the last fixture. Choose a unit to be the Master. Select NAFA/NASL OR NStS (see below for readout)depending upon which master mode your require. The master unit must be the first unit in line. Finally ,chain the units together using DMX cable. To set the pan to inversion Press the MENU until it shows RPOF. Use the UP/DOWN buttons until it shows RPON, press ENTER to confirm. « ‹ Prev3456789Next › » Summary of Easymove XL 60 Spot Page 1User’s manual easymove xl 60 spot.Page 22 / 9 table of content 1. Safety instructions........................................................................................................................... 3 2. Introduction ....................................................................................................................Page 33 / 9 1. Safety instructions for safe and efficient operation be careful with heat and extreme temperatureavoid exposing it to direct rays of the sun or near a heating appliance. Not put it in a temperature bellow 41°f /5°c, or exceeding 95°f /35°c. Keep away from humidity, water and dust do not pla...Page 44 / 9 2. Introduction - 11 dmx channels - pan 630°, tilt 270° - colorwheel: 7 colours + open, rainbow effect - gobowheel: 6 gobos+open, wheelrotation - variable electronic strobo - variable electronic dimmer (0-100%) - led display menu with invert - possibility to set manufacturers settings - fan co...Page 55 / 9 can support. Maximum recommended serial data link distance:500 meters(1640ft). Maximim recommended number of fixtures on a serial dqta link:32 fixtures. 3.3. 3 to 5 pin xlr converter note! If you use a controller with a 5 pin dmx output connetor. You will need to use a 5pin to 3 pins adapter t...Page 66 / 9 button to select the menu function currently displayed, or to enable a menu option. To return to the previous option or menu without changing the value, press the no alterative worth that return re-option or menu , press(menu)button 4.2. Menu map rpon set up the dmx address a001 – a512 au01 fa...Page 77 / 9 to set the tilt to inversion press the menu until it shows rtof use the up/down buttons until it shows rton, press enter to confirm. Display inversion press the menu until it shows rdof. Use the up/down buttons until it shows rton, press enter to confirm. Default setting press the menu until i...Page 88 / 9 5.1. Dmx channel list.Page 9: B & K Braun Gmbh9 / 9 importeur: b & k braun gmbh industriestraße 1 d-76307 karlsbad www.Bkbraun.Com info@bkbraun.Com.