Vax careline: 0870 6061248 instruction manual please read carefully before using the carpet washer. Always fully extend the mains cable before use. Www.Vax.Co.Uk upright carpet washer vax model number: v-028m/ccw-501 upright carpet washer vax model number: v-028/ccw-502 upright carpet washer vax mod...
1. Diagram parts overview attachments (model: v-028/v-028mpt/v-028pt/ v-028pet only) 24. Hose wrap 25. Solution tube 26. Upholstery/stair hose adaptor 27. Upholstery/stair hose 28. Upholstery/stair attachment 29. Solution spray trigger 30. 8x screws (model: v-028/v-028pt/ v-028pet only) 28. 5x screw...
2. Safety information for household use only. When using the carpet washer, basic safety precautions should always be observed, including the following. 1. Do not leave the carpet washer unattended when plugged in. Unplug it from socket when not in use. 2. To prevent electric shock do not use outdoo...
Fig.3/4: insert the upper handle screw (as shown) and tighten until secure. Note: make sure the power cord is out of the way to avoid pinching. Back view note: model v-028m does not have hose wrap shown. Upper handle 4 use & function/tool caddy assembly/cord storage fig.3/5 fig.3/7 fig.3/6 fig.3/4 c...
Tool storage/preparing the carpet fig.3/8 fig.3/9 fig.3/10 fig.3/11 fig.3/12 place upholstery/stair hose adaptor, upholstery/stair hose, and the upholstery/stair attachment into their storing locations. Slide the adaptor end of hose into the left clip on tool caddy. Upholstery/ stair hose upholstery...
Pre-treating your carpet 6 5. Pre-treating your carpet (model: v-028mpt/v-028pt only) grasp the clean water tank under the handle while pressing the clean water tank latch. Tilt the clean water tank away from the carpet washer and remove. Unscrew the measuring cap from the back of the clean water ta...
7 pre-treating your carpet / how to operate fig.5/7 to pre-treat your carpet, step on the power on/off pedal to turn the cleaner on. Using the wand and the trigger, apply the pre-treatment solution to your carpets. Turning the spray nozzle clockwise or anti-clockwise will alter the spray pattern. Fi...
How to operate/carpet cleaning 8 fill measuring cap with solution (approximately 4 capfuls). Pour into clean water tank. Note: use only vax aaa carpet cleaner solution. Using other cleaning solutions may cause excess foaming. Excessive foam will cause the float to shut off the carpet washer prematur...
9 fig.8/1 important: for best cleaning results use a steady, moderate, forward and backward motion. Important: if the sound of the motor changes to a high pitch, this indicates the dirty water tank is full and must be emptied. 8. Accessories (model: v-028/v-028pt/v-028pet only) put carpet washer in ...
10 accessories/filters the carpet washer is equipped with a shut off valve within the dirty water tank. When the dirty water tank becomes full, the float will rise, shutting off the air flow through the nozzle. Note: the float in the carpet washer will shut off the suction when the dirty water tank ...
11 filters to empty dirty water tank, grasp handle with one hand and nozzle with the other and empty into sink. To clean, rinse tank thoroughly with clean water and let dry. Fig.9/4 remove filter from rear of dirty water tank lid. Fig.9/5 rinse dirty water tank and filter with warm tap water. Wipe a...
11. Troubleshooting warning: to reduce risk of personal injury, unplug carpet washer before servicing problem: carpet washer won’t pick- up or low suction cause: the dirty water tank door is not installed. Solution: insert the dirty water tank door. Cause: the dirty water tank door is not installed ...
13 uk service & help/technical specification 13. Technical specification power supply: 220-240/50hz motor power: 900w clean water tank volume: 4 litres dirty water tank volume: 2.0 litres filter system: foam block cord length: 7.5m weight: 8.9kg subject to technical change without notice. 12. Uk ser...
14 this page is intentionally blank vax v-028 range.Qxd 27/4/07 13:26 page 14.
15 this page is intentionally blank vax v-028 range.Qxd 27/4/07 13:26 page 15.
Eec statement of compliance manufacturer/eec importer: vax limited, hereby on our own responsibility, declare that the products v-028/ccw-502, v-028m/ccw-501, v-028mpt, v-028pt, v-028pet are manufactured in compliance with the following: safety: 73/23/eec low voltage directive, as modified by 93/68/...
