1. DL manuals
  2. Vax
  3. Vacuum Cleaner
  4. V027
  5. User Manual

Vax V027 User Manual

Manual is about: Parts checklist

Summary of V027

  • Page 1

    3 e a c 1 2 3 putting your cleaner together remove your rapide xl from the carton with caution. The handle is connected to the body by a cord. Note : do not tug or pull on the cord. Line up the handle to the upper body of the machine and slide into place. Secure from the back with the two smaller sc...

  • Page 2

    4 5 4 5 6 putting your cleaner together feed the cord through the slots on the back of the handle and push into place. Place a nut into the recess in the back of the upper handle. While holding the nut in place insert one of the large screws through the front of the upper handle and tighten. Repeat ...

  • Page 3

    6 7 2 3 4 tool storage slide the tool caddy downwards until it is secured in place. Note : the tool caddy can be removed for storage on a wall. 1 2 3 pre-treating your carpets with the carpet treatment wand and solution remove the clean water tank by pressing the clean water tank release and pulling...

  • Page 4

    8 5 6 remove solution tank cap. Caution : do not overfill. You should leave 1-2 cm of air space. Fill the tank with pre-treatment solution. Replace the solution tank cap. Return the solution tank to the cleaner making sure the solution tube lines up with the groove in the back of the solution tank. ...

  • Page 5

    10 10 pre-treating your carpets with the carpet treatment wand and solution using the wand and the trigger, apply pre-treatment solution to carpets. Turning the spray nozzle clockwise or anti-clockwise will alter the spray pattern. Caution: do not turn the soap switch on without solution in the tank...

  • Page 6

    12 13 4 5 6 how to operate your cleaner remove solution tank cap. Caution : do not overfill. You should leave 1-2 cm of air space. Fill the tank with vax aaa carpet cleaner. The cleaner can be stored with solution in the solution tank. It does not have to be removed after each use. However the solut...

  • Page 7

    14 15 1 2 3 how to operate your cleaner caution: do not turn the soap switch on without solution in the tank. Do not allow the solution tank to run dry. Plug the cord into an electrical socket. Step on the handle release pedal to put the cleaner into a cleaning position. Turn main power switch and s...

  • Page 8

    Hose attachments put the cleaner in its upright position. Turn the soap and power switches to the off position. Remove the hose from its stored position on the back of the cleaner. Lift the hose attachment cover located on the top of the dirty water tank. Insert the end of the hose into the tool ope...

  • Page 9

    7 8 9 hose attachments while depressing the blue solution spray trigger, pull the attachment in a downward motion. Release the trigger and push the attachment forward in the same path to remove dirty water and solution from upholstery. For heavily soiled areas, repeat if necessary. To rinse, remembe...

  • Page 10

    Hard floor cleaning 20 21 before assembling the accessories for hard floor cleaning, ensure that the cleaning solution soap tank is filled with multi hard floor solution. Please refer to the bottle for measuring quanitites. Do not use vax aaa carpet cleaner. N.B the hydrodry head should only be used...

  • Page 11

    Insert the four aa batteries into your power wash brush in locations shown. Next see section 17 for machine preparation. Now attach the power wash brush to the hose attachment by pushing hose end into power wash brush until it clicks into place. In order to release solution onto the desired areas de...

  • Page 12

    4 5 6 dirty water tank can be rinsed out with hot tap water to remove any remaining debris. Wipe and let dry thoroughly before storing to prevent mildew from forming. Note: do not use any chemicals when cleaning. Return the dirty water tank cap. Lift the dirty water tank handle and pull out the filt...

  • Page 13

    27 7 8 emptying the dirty water tank return dirty water tank to the base of the cleaner by tipping the nozzle down into the basin and dropping it into place. Lift the front of the cleaner base off the carpeting with one hand. Line up the black tabs with the grooves of the front nozzle. Lift the fron...

  • Page 14

    4 remove solution tank cap. 28 29 5 6 caution : do not overfill. You should leave 1-2 cm of air space. Fill the tank with post-treatment solution. Replace the solution tank cap. Return the solution tank to the cleaner making sure the solution tube lines up with the groove in the back of the solution...

  • Page 15

    30 31 10 caution: do not turn the soap switch on without solution in the tank. Do not allow the solution tank to run dry. To post-treat carpets be sure that the unit is stood in the upright position. Turn the power and soap switches on. The post-treatment solution and water automatically mix within ...

  • Page 16

    32 33 2 to install a new brushbar. Feed the brushbar through the opening until the screw plate and screw hole are lined up (as above). Note: the black cap behind the silver screw plate will be through the hole. Tilt cleaner off the carpet. Grasp the brush bar and pull the right side of its chamber. ...

  • Page 17

    • do not leave the appliance when plugged in. Unplug it from socket when not in use. • to prevent electric shock do not use outdoors • not to be used as a toy. Close supervision is necessary when used by or near children or the infirm. • use only as described in this user guide. • do not use with a ...

  • Page 18

    Mon-fri. 9.00am to 5.00pm. An answer phone is available out of these hours. If you have queries or concerns about using your vax, call the helpline. Calls are charged at the uk national rate. Please make a note of the serial number and model number of your vax before calling. There are over 400 appr...