Instruction manual batteryminder ® 2000 series charger / maintainer / desulfator rev. C-091911 p/n vdc2000-mnl vdc electronics, inc. 147d woodbury rd. Huntington, ny 11743 www.Batteryminders.Com techsupport@vdcelectronics.Com read and save these instructions includes: 2’ fused ring terminal cord set...
Batteryminder ® 2000 series rev. C-091911 page 2 p/n vdc2000-mnl table of contents safety instructions ...................................................................... 3 - 7 warning - risk of explosive gases ................................................. 4 personal precautions ................
Batteryminder ® 2000 series rev. C-091911 page p/n vdc2000-mnl underwriters laboratories (ul) required important safety instructions for the batteryminder 2000 series warning to reduce the risk of fire, electric shock, or injury to person, observe the following: 1. Save these instructions this manua...
Batteryminder ® 2000 series rev. C-091911 page 4 p/n vdc2000-mnl 6. Do not operate charger with damaged cord or plug – replace the cord or plug immediately. 7. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; call vdc electronics tech support dep...
Batteryminder ® 2000 series rev. C-091911 page 5 p/n vdc2000-mnl part that may cause explosion. G) remove personal metal items such as rings, bracelets, necklaces, and watches when working with a lead-acid battery. A lead-acid battery can produce a short-circuit current high enough to weld a ring or...
Batteryminder ® 2000 series rev. C-091911 page 6 p/n vdc2000-mnl e) do not set a battery on top of charger. 14. Dc connection precautions a) connect and disconnect dc output clips only after setting any charger switches to “off” position and removing ac cord from electric outlet. Never allow clips t...
Batteryminder ® 2000 series rev. C-091911 page 7 p/n vdc2000-mnl h) see operating instructions for length of charge information. 16. Follow these steps when battery is outside vehicle. A spark near the battery may cause battery explosion. To reduce risk of a spark near battery: a) check polarity of ...
Batteryminder ® 2000 series rev. C-091911 page 8 p/n vdc2000-mnl batteryminder 2000 series label indicator light table • power a/c power connected • battery connection battery connected correctly • battery connection battery connection reversed • battery weak • battery required soft start • battery ...
Batteryminder ® 2000 series rev. C-091911 page 9 p/n vdc2000-mnl quick connect instructions place the positive ( red ) clip on the positive battery terminal. Place the negative ( black) clip on the negative battery terminal. Plug in the batteryminder. Power and battery connection light should be gre...
Batteryminder ® 2000 series rev. C-091911 page 10 p/n vdc2000-mnl • float (sometimes called maintenance) is the charger’s long term stage. The charger can and should be left connected indefinitely. This will keep the battery fully charged ensuring no sulfate can form. The charger maintains float vol...
Batteryminder ® 2000 series rev. C-091911 page 11 p/n vdc2000-mnl • desulfation light flashes blue any time the unit is desulfating. The batteryminder desulfates any time it is outputting current. Temperature compensation light is green if the temperature is over 27°c/80°f, blue if the temperature i...
Batteryminder ® 2000 series rev. C-091911 page 12 p/n vdc2000-mnl input 100-240 vac, 50/60 hz, 0.65a output 2adc ± 0.2a float current 1ma - 2000ma size 5.69” l x 4.06” w x 2.1” h weight 1.56 lbs. Operating temperature -20°c / -4°f to 40°c / 104°f water resistance ip65 specifications table voltage ta...
Batteryminder ® 2000 series rev. C-091911 page 1 p/n vdc2000-mnl maintaining multiple batteries to properly charge or maintain multiple batteries they should all be the same type (gel, flooded or agm) and condition. It is ok to mix deep cycle and starter. Charge each battery individually before conn...
Batteryminder ® 2000 series rev. C-091911 page 14 p/n vdc2000-mnl.
Batteryminder ® 2000 series rev. C-091911 page 15 p/n vdc2000-mnl for repair or replacement all returns must be authorized by vdc electronics. In the event that you believe your product may be defective, you must speak to a vdc electronics technician at 1-800-379-5579 x206 (et) before proceeding fur...
Batteryminder ® 2000 series rev. C-091911 page 16 p/n vdc2000-mnl all returns must be authorized by vdc electronics after speaking to a vdc electronics technician at 800-379-5579 x206 (et). Please see our “repair or replacement” section of this manual for additional information. Batteryminder one-ye...
