- DL manuals
- VDO
- Other
- CONTISYS OBD -
- Instruction Manual
VDO CONTISYS OBD - Instruction Manual - Safety Precautions
Introduction
7
Safety precautions
The following guidelines are intended to ensure the safety of the operator whilst
preventing damage to the electrical and electronic components fitted to the vehicle.
Equipment - prior to commencing any test procedure on the vehicle, ensure that the
service tool, its harnesses and connectors are in good condition.
Polarity - always observe the correct polarity when connecting the service tool to the
vehicle battery
Before carrying out testing on a vehicle, the following procedure should always be
observed:
• Check the handbrake/parking brake is on.
• Check that neutral or park is selected.
• Keep test equipment and harnesses away from HT leads.
• Be aware of moving engine parts.
• Do not run engine in a confined space without adequate ventilation.
Communication problems
If communications cannot be established with the vehicle, follow the procedure below:
1. Check the correct system was selected from the menu.
2. Check the correct cable was used against the application list.
3. Disconnect both ends of the cable and ensure that no pins are bent or snapped.
4. Reset the control module on the vehicle by turning the ignition OFF and ON,
reconnect the service tool and try again.
If communications still cannot be established, contact the Product Support Team for
further assistance.
Summary of CONTISYS OBD -
Page 1
08/2009 - en(2.0) contisys obd instruction manual 08/2009 - en(2.0).
Page 2
2.
Page 3: Contents
I contents introduction overview.................................................................... 1 display screen ........................................................... 5 keypad ...................................................................... 5 connection ................................
Page 4: Contents
Ii contents appendix b: cables cable identification................................................... 78 appendix c: manufacturer compatibility eobd application .................................................... 83 fastcheck applications ........................................... 83 appendix d: ...
Page 5: Overview
Introduction 1 introduction overview nearly every new road vehicle, and many older vehicles, have multiple control modules that monitor and control different aspects of the vehicle (e.G. Engine, transmission, body, suspension, etc.). The contisys obd service tool has been specifically designed to co...
Page 6
Introduction 2 fastcheck epb • fastcheck epb (electronic parking brake) allows you to read and clear any fault codes stored by the selected system, and in addition can be used during brake operation checks or brake pad replacement. Fastcheck sas • fastcheck sas (steering angle sensor) allows you to ...
Page 7
Introduction 3 call costs the cost of calls to the contisys telephone hotline is dependent on your telephone service provider. The cost can vary between 0.0 (euro cent) pence (euro) per minute to 0.40 pence (euro cent) per minute from landlines, depending on where you are calling from. Calls from mo...
Page 8
Introduction 4 kit contents contisys obd kit 1. Service tool 2. Eobd cable 3. Carry case 4. Cd rom containing the operating instructions 5. Eobd pin-switchable cable 6. Eu power supply 7. Usb software update cable con0016 1 2 3 4 5 6 7 1 12 4 3 2 10 11 a l d c b i j k esc.
Page 9: Display Screen
Introduction 5 display screen the service tool screen is a backlit lcd capable of displaying four rows of text containing up to twenty characters. Keypad the service tool is operated via the 6-button keypad. The table below details the keypad buttons and their functionality. Key function select a me...
Page 10: Connection
Introduction 6 connection the service tool has a 15-way connector through which it can communicate to the vehicle via various interface cables. Connection to the specific system is via either the vehicle's eobd (j1962) diagnostic socket or by a system specific connector. Refer to the 'vehicle applic...
Page 11: Safety Precautions
Introduction 7 safety precautions the following guidelines are intended to ensure the safety of the operator whilst preventing damage to the electrical and electronic components fitted to the vehicle. Equipment - prior to commencing any test procedure on the vehicle, ensure that the service tool, it...
Page 12: What Is Eobd?
Eobd application 8 eobd application what is eobd? The american environmental protection agency and the european government have set targets for reducing the levels of pollution produced by passenger and commercial vehicles. In order to ensure that these targets can be met, manufacturers are required...
Page 13
Eobd application 9 identifying compliant vehicles all petrol engine vehicles manufactured since 2000 should be eobd compliant. Some manufacturers began incorporating on-board diagnostic systems as early as 1994, however not all are 100% compliant. All diesel engine vehicles are expected to have supp...
Page 14: Diagnostic Trouble Codes
Eobd application 10 diagnostic trouble codes diagnostic trouble codes (dtcs) are divided into mandatory and voluntary codes. Mandatory codes are allocated by the iso (international standards organisation) / sae (society of automotive engineers). Voluntary codes are allocated by various vehicle manuf...
Page 15
Eobd application 11 interpreting eobd fault codes use the following rules to determine the basic meaning of an eobd fault code. The first character indicates which area of the vehicle the code applies to. The second character specifies the type of code: if the first character was 'p' (powertrain) th...
Page 16: Using Eobd Application
Eobd application 12 using eobd application connection and basic operation 1. Connect the eobd (j1962) cable (a2c59512072) to the service tool and secure the fixing screws. 2. Ensure the vehicle's ignition switch is in the '0' position. J1962 diagnostic socket 3. Connect the service tool to the vehic...
Page 17
Eobd application 13 if communication with the on-board diagnostics is successful, then the display will report that the service tool is checking the vehicle's system readiness tests. Note: the vehicles ignition must be on for successful communication with the vehicle control modules. 7. The service ...
Page 18: Menu Options
Eobd application 14 menu options not all vehicle control modules will support all of the options available from the menu. If an option is not supported the service tool will display either “not supported” or “not available”. This is a limitation of the software on the vehicle control modules and not...
Page 19
Eobd application 15 o2 sensor tests eobd has an optional mode for monitoring the oxygen sensor test results depending on the method used by the vehicle manufacturer to comply with the requirement for oxygen sensor monitoring. If the manufacturer does use this mode not all tests need to be supported....
Page 20
Eobd application 16 system readiness when the ignition is turned on the vehicles control modules perform a number of tests on the system (system readiness tests). If the conditions are not correct for the controller to perform the test e.G. If the engine is too cold, "not ready" status will be repor...
Page 21: Introduction
Fastcheck 17 fastcheck introduction the 'fastcheck' applications allow the service tool to communicate with other system control modules on the vehicle. Connection to the specific system is via either the vehicle's eobd (j1962) diagnostic socket or by a system specific connector. Refer to the 'vehic...
Page 22: Safety Instructions
Fastcheck 18 safety instructions warning: general safety • all operations must be carried out in a well ventilated area away from open flame and heat sources. • ensure the vehicle is stationary and the handbrake (parking brake) is applied before carrying out any maintenance/diagnostic work. Warning:...
Page 23
Fastcheck 19 warning: electronic parking brake (epb) safety • ensure that you are fully familiar with the braking system and its operation before commencing any work. • the epb control system may be required to be deactivated before carrying out any maintenance/diagnostic work on the brake system. T...
Page 24: Fastcheck Abs
Fastcheck 20 fastcheck abs connection using the vehicle application list on the cd-rom, identify the required interface cable for the vehicle system to be tested. Connect the cable to the service tool and secure the fixing screws. Note: if the vehicle being tested is a bmw with a 20 pin connector an...
Page 25
Fastcheck 21 if using the eobd (j1962) pin-switchable cable (a2c59512073), ensure the settings on the switch box correspond to the settings listed for the vehicle and system being tested. Warning: incorrect settings on the switch box may cause irreparable damage to the vehicle's electrical system. E...
Page 26
Fastcheck 22 select the required menu option using the and keys and press to confirm. The service tool will attempt to establish communication with the vehicle system. If communication is unsuccessful, refer to ‘communication problems’, page 7 . Read dtcs if any dtc codes are present in the system, ...
Page 27: Fastcheck Airbag
Fastcheck 23 fastcheck airbag connection using the vehicle application list on the cd-rom, identify the required interface cable for the vehicle system to be tested. Connect the cable to the service tool and secure the fixing screws. If using the eobd (j1962) pin-switchable cable (a2c59512073), ensu...
Page 28
Fastcheck 24 use the and keys to select the 'fastcheck airbag' application and press to confirm the selection. To return to the previous menu, press the key. Turn the vehicle's ignition on. Use the and keys to select the vehicle manufacturer and press to confirm the selection. Dependent upon the veh...
Page 29
Fastcheck 25 clear dtcs diagnostic trouble codes can be cleared using the 'clear dtcs' option. When using the option you will be prompted to turn the ignition off. Wait until prompted before switching the ignition back on. Verify that the code(s) have been cleared by selecting 'read dtcs'. Bmw vehic...
Page 30: Fastcheck Climate
Fastcheck 26 fastcheck climate connection using the vehicle application list on the cd-rom, identify the required interface cable for the vehicle system to be tested. Connect the cable to the service tool and secure the fixing screws. If using the eobd (j1962) pin-switchable cable (a2c59512073), ens...
Page 31
Fastcheck 27 use the and keys to select the 'fastcheck climate' application and press to confirm the selection.To return to the previous menu, press the key. Turn the vehicle's ignition on. Use the and keys to select the vehicle manufacturer and press to confirm the selection. Dependent upon the veh...
Page 32
Fastcheck 28 clear dtcs diagnostic trouble codes can be cleared using the 'clear dtcs' option. When using the option you will be prompted to turn the ignition off. Wait until prompted before switching the ignition back on. Start the engine to force the control module to run a system check. Verify th...
Page 33: Fastcheck Epb
Fastcheck 29 fastcheck epb connection using the vehicle application list, identify the required interface cable for the vehicle system to be tested. Connect the cable to the service tool and secure the fixing screws. If using the eobd (j1962) pin-switchable cable (a2c59512073), ensure the settings o...
Page 34
Fastcheck 30 power for the service tool is provided by the vehicle connector. Once connected, the service tool will perform an internal self test and then the screen will display the version of the current software before displaying the main menu. Use the and keys to select the 'fastcheck epb' appli...
Page 35
Fastcheck 31 if either of the above tests fail (pressure reading not correct) the epb assembly should be removed and re-assembled. Electronic parking brake (epb) emergency release calibration checks the epb emergency release is working correctly. This test should be performed after work has been com...
Page 36
Fastcheck 32 exit maintenance mode this function is used to put the system back into an operational state after work has been carried out by the technician. Callipers are closed to the applied position, and normal operation is available again. Pre-test conditions: • the vehicle must be stationary • ...
Page 37
Fastcheck 33 it should be used if it is suspected that there is a fault with the control module, wiring, or the actuators (if the parking brake will not engage/disengage when manually operated). Note: this function can not be performed while the parking brake system is in maintenance mode. It should...
Page 38
Fastcheck 34 renault - handbrake there are test functions available under the circuit tests section of the handbrake menu these are described below. Release brakes pre-test conditions: • the vehicle must be stationary • the vehicle must be on level ground • the engine must not be running the test re...
Page 39
Fastcheck 35 brake pad replacement/service sequence the epb system must be deactivated and completely released and the ignition must be on. Note: the sequence must be performed in the correct order else the braking system maybe left in a non-operational state. Release brakes select the 'release brak...
Page 40
Fastcheck 36 pad thickness the brake pad thickness must now be entered by selecting pad thickness from the replace pads menu. The current value is displayed on screen. Press the key to change value then enter the new value between 3-14mm. Press the key to test the new value message will be displayed...
Page 41: Fastcheck Sas
Fastcheck 37 fastcheck sas connection using the vehicle application list on the cd-rom, identify the required interface cable for the vehicle system to be tested. Connect the cable to the service tool and secure the fixing screws. Note: if the vehicle being tested is a bmw with a 20 pin connector an...
Page 42
Fastcheck 38 use the and keys to select the 'fastcheck sas' application and press to confirm the selection. To return to the previous menu, press the key. Turn the vehicle's ignition on. Use the and keys to select the vehicle manufacturer and press to confirm the selection. Dependent upon the vehicl...
Page 43
Fastcheck 39 to view the next dtc (if more than 1 was found), scroll to the end of the text and press the key. To return to the menu, scroll to the end of the text and press the key. Clear dtcs diagnostic trouble codes can be cleared using the 'clear dtcs' option. When using the option you will be p...
Page 44: Fastcheck Service
Fastcheck 40 fastcheck service connection using the vehicle application list on the cd-rom, identify the required interface cable for the vehicle system to be tested. Connect the cable to the service tool and secure the fixing screws. Note: if the vehicle being tested is a bmw fitted with both a 20 ...
Page 45
Fastcheck 41 turn the vehicle's ignition on. Use the and keys to select the vehicle manufacturer and press to confirm the selection. Dependent upon the vehicle manufacturer and model different menu options will then be available. Alfa romeo vehicles (uk only) for alfa romeo vehicles with the mannesm...
Page 46
Fastcheck 42 14. Switch ignition off. This procedure is necessary to ensure that the value read from the odometer by the dashboard, when a service reset is performed by the service tool, is in kilometres. The dashboard can then calculate the 'number of miles to service' correctly. On the european co...
Page 47
Fastcheck 43 cbs is a system in which the vehicle calculates and monitors the status of serviced components and fluid levels as well as time and mileage based services. The following table displays possible service options together with the control module used to reset each option. The service tool ...
Page 48
Fastcheck 44 the percentage reset value. The estimated distance too or the next service date. The service counter. Note: the vehicle inspection and exhaust emission inspection only display the date of the next service. The service option list is displayed in priority order, with the most urgent firs...
Page 49
Fastcheck 45 a final confirmation of the new data entered is displayed. Press the key to store the new information. To cancel the correction and return to the service option list press the key. Note: the maximum reset value will be the current value of the selected service option. The service counte...
Page 50
Fastcheck 46 applicable vehicles: • bmw 1 series (e81/e87) • bmw 3 series (e90/e91/e92/e93) • bmw 5 series (e60/e61) • bmw 6 series (e63/e64) • bmw 7 series (e65) note: the can converter (a2c59512664) harness must be used. Battery change: after fitting a new battery, the battery change function shou...
Page 51
Fastcheck 47 the service tool will communicate with the instrument pack to determine the vehicle model. If the vehicle model is unknown the operator must manually select the vehicle. Note: vehicle must not be moving during this procedure and all doors must be closed. The service tool will check the ...
Page 52
Fastcheck 48 vectra-c / signum only a straight reset is available on these vehicles. The programmed service interval values of miles and days until the next service cannot be altered. Note: the engine oil used on these vehicles is 'long-life oil'. When the engine oil is changed the technician must u...
Page 53
Fastcheck 49 the service tool will check the engine speed to ensure that the engine is not running then read the current value of 'remaining oil life' from the engine control module and display. If the value is less than 15% the oil must be changed and a reset performed. The service tool will then p...
Page 54
Fastcheck 50 additional work this function is used to add additional service options to the latest service held within the service memory. The application will display a menu of all available additional work options applicable for the vehicle. Press the and keys to scroll through the available list....
Page 55
Fastcheck 51 undo additional this function cancels any additional work applied the latest service stored in the service history the last preformed service. A warning will be displayed before the undo process is performed. This option is only intended for resetting an additional service option that h...
Page 56
Fastcheck 52 saab vehicles select 'interval and oil' and press to confirm the selection. To return to a previous menu, press the key. You will receive the message "saab reset" to confirm the reset process was completed successfully. Volvo vehicles select 'service' and press to confirm the selection....
Page 57
Fastcheck 53 variable service reset (vag) for some vag (audi and vw) vehicles manufactured since 2000, the variable service reset option must be used. Refer to the vehicle application list. Warning: changing the baseline / learn values of any channel could have adverse effects on engine performance ...
Page 58
Fastcheck 54 service reset adaption channels and values model adaption channel adaption reset audi 100 oil 05 00015 1991 on service 1 (distance) 06 00030 service 1 (time) 07 00036 service 2 08 00073 audi a8 oil 05 15000 1994 - 1995 service 1 (distance) 06 30000 service 1 (time) 07 00365 service 2 08...
Page 59
Fastcheck 55 lupo 10 00150 1999 on 11 00300 12 00360 audi a4 oil 05 00015 1995 - 1998 service 1 (distance) 06 00030 service 1 (time) 07 00036 service 2 08 00073 audi a4 oil + service 02 00000 1998 on oil 02 00010 service 02 00001 audi a3 oil + service 02 00000 1997 on oil 02 00000 service 02 00000 m...
Page 60
Fastcheck 56 marking and coding service intervals no. Of data carrier qgo qg1 qg2 vehicle equipment vehicles not equipped for long life service vehicles equipped for long life service vehicles not equipped for long life service service variant no long life oil required if long life oil is used at se...
Page 61
Fastcheck 57 diagnostic connector locations alfa romeo j1962 under the driver’s side dashboard or in the fuse box. 3-pin airbag/abs • engine compartment – normally centre: 145, 146, 155, gtv/ spider • engine compartment – normally right: 145, 146, 155, 164, gtv/spider • under dashboard – driver’s si...
Page 62
Fastcheck 58 bmw 20-pin round connector engine compartment. J1962 if the vehicle is fitted with a j1962 diagnostic connector, this can usually be located in the driver's footwell behind a cover. Note: if the bmw vehicle under test has both the round (20 pin) diagnostic connector and the j1962 (16 pi...
Page 63
Fastcheck 59 citroen j1962 saxo: - under dashboard - passenger side. Ax (1997), berlingo: - under dashboard - driver's side c3, c6, c8, xsara, picasso, xantia, evasion: - fascia fuse box. C5: - glove box. C1: - to left of steering column. C6: - centre console compartment. 30-pin connector saxo: - pa...
Page 64
Fastcheck 60 fiat j1962 driver’s side dashboard or in the fuse box with the exception of the palio/rst where it is in the centre console, under the handbrake. 3-pin airbag/abs • under dashboard – driver’s side/ passenger glove box: barchetta, bravo- brava, coupe, doblo, ducato, idea, marea, multipla...
Page 65
Fastcheck 61 gm vauxhall/ opel j1962 corsa c, astra g, astra h, meriva, vectra b, zafira a, zafira b: - below cover - front of handbrake. Agila, tigra, speedster/ vx220, sintra, vivaro: - below dashboard - driver’s side. Astra f, corsa b, omega b: - fuse box - passenger compartment. Corsa c, corsa d...
Page 66
Fastcheck 62 mercedes benz 38-pin round connector engine compartment - usually along bulkhead, but the precise location may vary. Note: for those vehicles which have both the round 38-pin connector and the obd ii connector: • the round 38-pin connector should always be used to retrieve data via the ...
Page 67
Fastcheck 63 mercedes obd-1 16-pin connector block engine compartment - usually on the bulkhead adjacent to the fusebox. Mg rover j1962 the diagnostic connector is located in one of three positions: • behind the 'a' post lower trim panel in the driver’s footwell. • on a bracket inside the centre con...
Page 68
Fastcheck 64 peugeot j1962 106 (1997 on): - under dashboard - passenger side. 206, 306, 806, partner (1997 on): - under dashboard - driver's side. 307 (to 2004), 406 (1997 to 2000), 807: - fascia fuse box. 107: - to left of steering column. 307 (2004 on): - behind ashtray in centre console. 406 (200...
Page 69
Fastcheck 65 seat j1962 alhambra: - centre console/ footwell - passenger. Arosa: - fascia - driver side. Ibiza, cordoba: - centre console - driver side. Toledo: - centre console. Skoda j1962 favourit, felicia (1.3), forman: - under bonnet - suspension turret - near side. Felicia (1.6): - footwell - ...
Page 70
Fastcheck 66 vw 2-pin iso 9141 engine compartment relay box. J1962 bora: - centre console. Corrado, passat: - dashboard - centre. Golf, vento: - dashboard - centre (remove ashtray). Lupo: - centre console, storage compartment or front ashtray. Polo: - dashboard - rh. Sharan: - under gear lever cover...
Page 71: Overview
User menu 67 user menu overview use the and keys to select the required function and press to confirm the selection. Note: press to return to the main menu. Obd dtc lookup this option is used to look up a description of a known dtc. 1. Use the and keys to move the cursor under the required dtc chara...
Page 72
User menu 68 tester setup the tester setup allows you to change the live data units, change the way live data is displayed and adjust the contrast of the screen. 1. Select 'live data units' from the tester setup menu. 2. The currently selected live data units will be displayed on the screen. E.G. 'm...
Page 73: Security
User menu 69 self test 1. Use the and keys to select the required test. 2. Press to confirm selection. 3. Follow on-screen instructions to carry out specified test. 4. Press the or key as appropriate, to return to the self test menu. Software version 1. Once selected, the contisys obd version number...
Page 74
User menu 70 show securitykey 1. Once selected, the security key is displayed on the screen as 25 characters. If it is incorrect the message 'key is invalid' will be displayed as well, and the key may be pressed for further information which may be asked for by product support. 2. Press the or key t...
Page 75
User menu 71 get fw version 1. Select the 'get fw version' item to display the current version of the firmware within the can converter cable (a2c59512664). 2. Press to return to the user menu. Update firmware 1. Select the 'update fw version' item to check and update the version of the firmware wit...
Page 76: Cleaning
General information 72 general information cleaning to maintain the condition and serviceability of the service tool, it is advisable to follow the cleaning procedures below: warning: do not use solvents such as petroleum based cleaning agents, acetone, petrol, trichlorethylene etc. These types of h...
Page 77: Specification
General information 73 specification contisys obd complies with iso/dis 15031 part 4 as an eobd service tool. Voltage requirements - 8.0 volts to 16.0 volts dc current requirement - 750ma max. Display - 20 characters by 4 lines lcd with led back light operating temperature range - 0°c to 50°c declar...
Page 78: Glossary of Terms
Appendix a: glossary 74 glossary glossary of terms term description j1962 the sae standard that defines the 16-pin connector used for eobd abs anti-lock brake system a/c air conditioning ac air cleaner air secondary air injection a/t automatic transmission or transaxle sap accelerator pedal b+ batte...
Page 79
Appendix a: glossary 75 eeprom electrically erasable programmable read only memory efe early fuel evaporation egr exhaust gas re-circulation egrt egr temperature ei electronic ignition em engine modification eobd european on-board diagnostics eprom erasable programmable read only memory evap evapora...
Page 80
Appendix a: glossary 76 koeo key on, engine off koer key on, engine running ks knock sensor ksm knock sensor module lt long term fuel trim maf mass airflow sensor map manifold absolute pressure sensor mc mixture control mdp manifold differential pressure mfi multi-port fuel injection mi malfunction ...
Page 81
Appendix a: glossary 77 scb supercharger bypass sdm sensing diagnostic mode sfi sequential fuel injection sri service reminder indicator srt system readiness test st short term fuel trim tb throttle body tbi throttle body injection tc turbocharger tcc torque converter clutch tcm transmission or tran...
Page 82: Cable Identification
Appendix b: cables 78 cables cable identification standard cables a2c59512072 - eobd connecting cable a2c59512073 - eobd multiplex cable a2c59512076 - updater cable (supplied with contisys obd) con0020 con0021 1 12 4 3 2 10 11 a l d c b i j k con0097.
Page 83
Appendix b: cables 79 optional cables a2c59512060 – vag obd cable a2c59512061 – psa obd cable a2c59512065 – mercedes sprinter cable con0022 con0023 con0077.
Page 84
Appendix b: cables 80 a2c59512066 – mercedes obd cable a2c59512067 – bmw obd cable a2c59512069 - fiat/alfa/lancia obd cable con007 8 con0024 con0025.
Page 85
Appendix b: cables 81 a2c59512070 - fiat/alfa/lancia ls can cable a2c59512664 - fast can cable con0026 con0027.
Page 86
Appendix b: cables 82 cable part number cross reference table description vdo part no. Ate long part no. Ate short part no. Scan tool kit a2c59512059 03.9301-2000.4 782000 carry case a2c59512097 03.9301-2020.1 782020 vag 2 x 2-pin cable a2c59512060 03.9301-2010.1 782010 psa cable a2c59512061 03.9301...
Page 87: Eobd Application
Appendix c: manufacturer compatibility 83 manufacturer compatibility eobd application the service tool can communicate with any eobd compliant vehicle fitted with a j1962 diagnostic socket. The following should be used as a guide. • all petrol engine vehicles manufactured since 2000. • all diesel en...
Page 88: Alfa Romeo
Appendix d: manual service reset 84 manual service reset service reminder indicator (sri) on some older vehicles it is not possible to reset the sri by using the service tool. The manufacturers of these vehicles generally have bespoke service reset tools specifically for this task. However on a numb...
Page 89: Audi
Appendix d: manual service reset 85 audi audi a4 and a6 (1995 - 1999) 1. With the ignition switch in the off position, press and hold button a whilst turning the key to the on position. 2. The message “service oil” will appear. If the message does not display, repeat step 1. 3. Pull out the button b...
Page 90: Bmw
Appendix d: manual service reset 86 bmw bmw 3 series (e46), bmw 7 series (e38), bmw 5 series (e39) and bmw x5 (e53) bmw x3 (e83) and bmw z4 (e85) button a arrowed in illustrations the service interval display (sia) can be reset using the reset button for the trip distance recorder on the instrument ...
Page 91: Citroen
Appendix d: manual service reset 87 do include time-based inspection then the time-based inspection status will be shown. 7. The display will now indicate the remaining time to service. If the remaining time is displayed with 'rst' then the service interval can be reset. 8. To reset the time to serv...
Page 92
Appendix d: manual service reset 88 berlingo 2002 onwards 1. Switch ignition off. 2. Press and hold button a . 3. Switch ignition on. 4. Keep button depressed for 10 seconds. The display will now read '0' and the spanner icon will extinguish. C3 1. Switch ignition off. 2. Press and hold button a . 3...
Page 93
Appendix d: manual service reset 89 c5 1. Switch ignition off. 2. Press and hold button a . 3. Switch ignition on. 4. Keep button depressed for 10 seconds. The display will now read '0' and the spanner icon will extinguish. C8 1. Switch ignition off. 2. Press and hold button a . 3. Switch ignition o...
Page 94
Appendix d: manual service reset 90 dispatch/jumpy 1. Switch ignition off. 2. Press and hold button a . 3. Switch ignition on. 4. Keep button depressed for 10 seconds. The display will now read '0' and the spanner icon will extinguish. Relay ii/jumper ii (2002 onwards) 1. Switch ignition off. 2. Pre...
Page 95
Appendix d: manual service reset 91 saxo 1. Switch ignition off. 2. Press and hold button a . 3. Switch ignition on. 4. Keep button depressed for 10 seconds. The display will now read '0' and the spanner icon will extinguish. Synergie/evasion 1. Switch ignition off. 2. Press and hold button a . 3. S...
Page 96
Appendix d: manual service reset 92 xantia 1. Switch ignition off. 2. Press and hold button a . 3. Switch ignition on. 4. Keep button depressed. The spanner icon and the service interval will illuminate for 5 seconds, then extinguish. Xsara (1997 - 2000) 1. Switch ignition off. 2. Press and hold but...
Page 97
Appendix d: manual service reset 93 xsara (2000 onwards) 1. Switch ignition off. 2. Press and hold button a . 3. Switch ignition on. 4. Keep button depressed for 10 seconds. The display will now read '0' and the spanner icon will extinguish. Xsara picasso 1. Switch ignition off. 2. Press and hold bu...
Page 98: Fiat
Appendix d: manual service reset 94 fiat (1994 - 2000) 1. Turn the ignition key to off. 2. Press button a and keep it pressed. 3. Turn the ignition key to on. 4. Keep button a pressed for about 10 seconds. 5. The display will show '0' and the spanner symbol will disappear. Co n 0069 a.
Page 99: Gm Vauxhall/opel
Appendix d: manual service reset 95 gm vauxhall/opel omega-b, vectra-b 1999 onwards 1. Switch ignition off. 2. Press and hold button a . 3. Switch ignition on. 4. Keep button depressed until three dashes are displayed '---'. 5. Switch ignition off to check the service request has been cleared. Con00...
Page 100: Lancia
Appendix d: manual service reset 96 lancia (1994 - 2000) 1. Turn the ignition key to off. 2. Press button a and keep it pressed. 3. Turn the ignition key to on. 4. Keep button a pressed for about 10 seconds. 5. The display will show '0' and the spanner symbol will disappear. Co n 0069 a.
Page 101: Land Rover
Appendix d: manual service reset 97 land rover range rover iii 2002 onwards (all except japan and nas) 1. Switch ignition off. 2. Press and hold button a . 3. Keep button depressed and switch the ignition to position i. 4. Keep button depressed for 5 seconds, until the 'sia reset' appears. 5. The di...
Page 102: Mercedes
Appendix d: manual service reset 98 mercedes mercedes (1998 - 2007) with the flexible service system and multi-function steering wheel controls 1. Switch ignition on. 2. Use buttons and to scroll through the multi-function display until the trip odometer and main odometer readings are displayed, or ...
Page 103: Peugeot
Appendix d: manual service reset 99 peugeot 106 1. Switch ignition off. 2. Press and hold button a . 3. Switch ignition on. 4. Keep button depressed for 10 seconds. The display will now read '0' and the spanner icon will extinguish. 206 1. Switch ignition off. 2. Press and hold button a . 3. Switch ...
Page 104
Appendix d: manual service reset 100 306 1. Switch ignition off. 2. Press and hold button a . 3. Switch ignition on. 4. Keep button depressed for 10 seconds. The display will now read '0' and the spanner icon will extinguish. 307 1. Switch ignition off. 2. Press and hold button a . 3. Switch ignitio...
Page 105
Appendix d: manual service reset 101 406 1. Switch ignition off. 2. Press and hold button a . 3. Switch ignition on. 4. Keep button depressed for 10 seconds. The display will now read '0' and the spanner icon will extinguish. 607 1. Switch ignition off. 2. Press and hold button a . 3. Switch ignitio...
Page 106
Appendix d: manual service reset 102 806 1. Switch ignition off. 2. Press and hold button a . 3. Switch ignition on. 4. Keep button depressed for 10 seconds. The display will now read '0' and the spanner icon will extinguish. 807 1. Switch ignition off. 2. Press and hold button a . 3. Switch ignitio...
Page 107
Appendix d: manual service reset 103 boxer ii 2002 onwards 1. Switch ignition off. 2. Press and hold button a . 3. Switch ignition on. 4. Keep button depressed for 10 seconds. The display will now read '0' and the spanner icon will extinguish. Expert 1. Switch ignition off. 2. Press and hold button ...
Page 108
Appendix d: manual service reset 104 partner 1999 - 2002 1. Switch ignition off. 2. Press and hold button a . 3. Switch ignition on. 4. Keep button depressed for 10 seconds. The display will now read '0' and the spanner icon will extinguish. Partner 2002 onwards 1. Switch ignition off. 2. Press and ...
Page 109: Renault
Appendix d: manual service reset 105 renault oil level the lamp illustrated is an oil level low warning indicator and not a service interval indicator. When the engine oil is at the correct level, this lamp will automatically extinguish. Malfunction indicator lamp (mil) the lamps illustrated above, ...
Page 110
Appendix d: manual service reset 106 clio iii (models with trip computer; 2006 onwards) scenic ii (models with trip computer; 2003 onwards) 1. Switch ignition on. 2. Press and release display reset button a or b on the tip of the wiper lever until the 'distance before next' service information is di...
Page 111
Appendix d: manual service reset 107 laguna ii (2001 onwards) 1. Switch ignition on. 2. Repeatedly press reset button a until spanner icon flashes and the distance remaining until the next service appears in the odometer display. 3. Press and hold button b until the display has flashed 8 times. 4. R...
Page 112
Appendix d: manual service reset 108 safrane 1. Press and hold button a . 2. Switch ignition on. 3. Continue to depress the button until the spanner icon stops flashing and remains illuminated. The indicator will show the appropriate service interval (e.G. 6000 miles/10000 km). 4. Release the reset ...
Page 113: Smart
Appendix d: manual service reset 109 smart roadster 1. Turn the ignition on and within 4 seconds select the service interval display by pressing button a on the top of the instrument cluster (repeatedly until the service interval is displayed). 2. Hold button a down and turn the ignition off. 3. Tur...
Page 114: Volkswagen
Appendix d: manual service reset 110 volkswagen cabrio, golf iii, gti, jetta iii (1993 - 1995) and jetta (1996) one of four service codes may be displayed on instrument panel according to distance travelled. Each service code displayed determines the type or level of maintenance required. The servic...
Page 115: Volvo
Appendix d: manual service reset 111 volvo volvo 240 (1986 - 1989) reach behind the instrument panel and push the lever located between the tachometer and the speedometer. Volvo 240 (1990 - 1993) 1. Remove the plug from the face of the instrument panel between the clock and the speedometer. 2. Inser...
Page 116
Appendix d: manual service reset 112 volvo 740 (1986 - 1988) reach behind the instrument panel and push the button located to the left of the speedometer. Volvo 740 (1989 - 1992) 1. Remove the plug from the face of the instrument panel between the clock and the speedometer. 2. Insert a thin-bladed t...
Page 117
Appendix d: manual service reset 113 volvo 760 (1986 - 1990) 1. Remove the plug from the face of the instrument panel between the clock and the speedometer. 2. Insert a thin-bladed tool into the cavity and press the reset button. Volvo 780 (1988 - 1990) reach behind the instrument panel and push the...
Page 118
Appendix d: manual service reset 114 volvo 850 (1993 - 1995) fitted with the yazaki instrument panel note: this instrument panel has the odometer located above the speedometer needle. 1. Remove the plug from the face of the instrument panel between the clock and the speedometer. 2. Insert a thin-bla...
Page 119
Appendix d: manual service reset 115 volvo 850 (1993 - 1995) fitted with the vdo instrument panel note: this instrument panel has the odometer located below the speedometer needle. 1. With the ignition switch in the on position and the engine not running. Diagnostic module located in engine compartm...
Page 120
Appendix d: manual service reset 116 volvo 940 (1991 - 1995) 1. Remove the plug from the face of the instrument panel between the clock and the speedometer. 2. Insert a thin-bladed tool into the cavity and press the reset button. Volvo 960 (1991 - 1995) 1. Remove the plug from the face of the instru...