1. DL manuals
  2. VDO Cyclecomputing
  3. Bicycle Accessories
  4. Cytec C05+
  5. Instruction Manual

VDO Cyclecomputing Cytec C05+ Instruction Manual

Manual is about: VDO Bicycle Computer Installation and Operation Manual

Summary of Cytec C05+

  • Page 1

    Bedienungsanleitung instruction manual manuel d´installation et d´utilisation manuale d´installazione e funzionamento instalacion y operaciÓn manual handleiding nÁvod k montÁŽi a obsluze instrukcja obslugi licznika installations og betjeningsvejledning bruksanvisning bruksanvisning asennus ja kÄyttÖ...

  • Page 2

    1 gb installation and operation manual - vdo cytec c05+ preface thank you for buying a vdo cytec bicycle computer. The more familiar you get with this model, the more enjoyable your trips are going to be. Please read thoroughly all the information provided in this manual. You are getting important a...

  • Page 3: Screw

    Gb 2 warning: before tightening the handlebar holder, make sure to adjust the position of the computer head (inclination) when the lcd-display is best visible for you. Only when you find the best position tighten the screw. Screw.

  • Page 4

    3 gb 1.2 mounting the speed transmitter / sender the sensor should be mounted on the same side of the fork as the holder is on the handlebar. Make sure to position the respective rubber shim between fork and sender, position the curved back of the sender next to the spokes and make sure the sender i...

  • Page 5

    Gb 4 1.3 mounting the spoke magnet distance between magnet and sensor should be approx. 1-5 mm. In case this distance is not achievable in the current positioning, slide the sensor and the magnet on the fork or spoke accordingly. Watch out: please remove the computerhead from the handlebar holder wh...

  • Page 6

    5 gb 1.4 installing battery into computer head to save battery power, your vdo cytec c05+ comes with the battery not yet fitted. Prior to initial use you have to install the battery first. Insert battery with positive (+) end on top. Watch out: once the battery is properly fitted, the computer immed...

  • Page 7

    Gb 6 1.5 function indicator your vdo cytec c05+ features a function indicator ((1)). When you are done mounting the computer, ((1)) flashes at the first rotation of the wheel. When the wheel-size is properly entered, actual speed is displayed as well.(see chapter 5). In case the function-indicator (...

  • Page 8

    7 gb unlock lock 1.Lock 2.Click 1.Press 2.Unlock.

  • Page 9

    Gb 8 3. Information features of your vdo cytec c05+ your vdo cytec c05+ provides you with following information: kmh-mph current speed indicated in either kmh or mph, featuring automatic conversion into mph dst trip counter, counts your trip distance up to 999,99 km or miles. Atm trip timer, keeps t...

  • Page 10

    This button / key has several functions. All functions of the button / key are outlined in the chart below. Your display button / key to length of pushing what is going on? Indicates following be pushed the button / key information dst-odo-clk-atm push mode key brief (0.1 sec) next information from ...

  • Page 11

    Gb 10 5.1 programming (setting up) your wheelsize in order for the vdo cytec c05+ to indicate your actual speed and your trip distance, the correct wheelsize has to be entered. Wheelsize is the outer circumference of the wheel including the tire. Following default is entered wheelsize = ws = 2124 mm...

  • Page 12

    11 gb watch out: in case you have selected mph readout you must enter your wheelsize in mm. Ws in mm 1x.

  • Page 13

    Gb 12 5.3 entering your wheelsize / entering odometer after initially installing the battery or after a battery change, your vdo cytec c05+ automatically switches into set-up mode for wheelsize and odometer. Start with step 3. You might as well enter the set-up mode for wheelsize and odometer at any...

  • Page 14

    13 gb in case you wish to enter the precise wheelsize you have measured yourself (i.E. 2257), please proceed with step 5. Step 5: not pressing the mode button with in 2 seconds will make the last digit (2124) flash and change the value (4-5-6-7...) once the correct digit (7) comes up, press the mode...

  • Page 15

    Gb 14 press immediatly 5 times to end press to stop switch to next press to stop switch to next press to stop switch to next press to stop switch to next press to stop switch to next please wait 2 sec. Until counting press to stop switch to next press to stop switch to next press to stop switch to n...

  • Page 16

    15 gb 5.4 setting the clock clk your vdo cytec c05+ features a clock with hour and minute display in 24 h mode to access the clock set-up mode proceed as follows: step 1: call in the clk information into your display step 2: press the mode button for 5 sec. The set-up mode for the clock starts. You ...

  • Page 17

    6. Resetting information to zero the following information may be reset to zero with your vdo cytec c05+: dst = trip distance atm = trip counter watch out: both these information are simultaneously reset to zero to reset either dst or atm, one of these informations has to be displayed. Resetting to ...

  • Page 18

    Hg 17 gb 8 . Battery change tip: take down your total distance and wheelsize prior to battery change. 8.1 changing the battery in the computer head see chapter 1.4. Watch out: old batteries require special disposal 9. Troubleshooting this chart outlines possible malfunctions, their causes and soluti...

  • Page 19

    Gb 18 8 . Battery change tip: take down your total distance and wheelsize prior to battery change. 8.1 changing the battery in the computer head see chapter 1.4. Watch out: old batteries require special disposal 9. Troubleshooting this chart outlines possible malfunctions, their causes and solutions...

  • Page 20

    19 gb contents 1 computer head 1 handlebar holder with screw 1 wireless transmitter with battery 12 v, type v23ga 1 rubber shim for sensor mount 1 spoke magnet 5 cable ties 1 battery 3 v, type cr 2032 1 installation and operation manual tip the cytec tin box easily holds a mini-tool and a spare tube...