1. DL manuals
  2. Vecow
  3. Desktop
  4. 9100 GTX950
  5. User manual

Vecow 9100 GTX950 User manual

Manual is about: Quad Core Intel Xeon/Core i7 Processor Embedded System with Intel C236 Chipset & NVIDIA GEFORCE GTX 950 Graphics

Summary of 9100 GTX950

  • Page 1

    User manual user manual 1.1.0 edition 20170718 ecs-9200/9100 gtx950 quad core intel ® xeon ® / core ™ i7 processor embedded system with intel ® c236 chipset & nvidia geforce ® gtx 950 graphics high performance, independent graphics, en50155.

  • Page 2: Record of Revision

    Ii version date page description remark 1.0 05/25/2017 all official release 1.1 07/18/2017 22,76-77 update record of revision.

  • Page 3: Fcc

    Iii this manual is released by vecow co., ltd. For reference purpose only. All product offerings and specifications are subject to change without prior notice. It does not represent commitment of vecow co., ltd. Vecow shall not be liable for direct, indirect, special, incidental, or consequential da...

  • Page 4: Order Information

    Iv part number description ecs-9204mx- gtx950 ecs-9200, nvidia geforce ® gtx 950, 6 gige lan w/4 x-coded m12 poe + , 2 ssd tray, 8 usb 3.0, 4 com, 1 m2dom, 3 sim, 32 isolated dio ecs-9204m- gtx950 ecs-9200, nvidia geforce ® gtx 950, 6 gige lan w/4 a-coded m12 poe + , 2 ssd tray, 8 usb 3.0, 4 com, 1 ...

  • Page 5: Order Accessories

    V part number description e3-1275 v6 7th generation intel ® xeon ® e3-1275 v6 processor (8m cache, up to 4.20 ghz, 80w) e3-1275 v5 6th generation intel ® xeon ® e3-1275 v5 processor (8m cache, up to 4.00 ghz, 80w) e3-1225 v5 6th generation intel ® xeon ® e3-1225 v5 processor (6m cache, up to 3.70 gh...

  • Page 6: Table of Contents

    Vi table of contents chapter 1 general introduction 1 1.1 overview 1 1.2 features 2 1.3 product specification 2 1.3.1 specifications of ecs-9204mx gtx950 2 1.3.2 specifications of ecs-9204m gtx950 4 1.3.3 specifications of ecs-9240 gtx950 7 1.3.4 specifications of ecs-9100 gtx950 9 1.4 supported cpu...

  • Page 7: Chapter   4

    Vii 3.5 installing cfast card 60 3.6 installing sim card 61 3.7 installing ssd/hdd 62 3.8 installing m.2 64 3.9 installing m2dom 65 3.10 mounting your ecs-9200/9100 gtx950 67 chapter 4 bios setup 73 4.1 entering bios setup 73 4.2 main 74 4.3 advanced 74 4.4 chipset 83 4.5 security 88 4.6 boot 89 4.7...

  • Page 8: General Introduction

    1 general introduction 1 general introduction vecow ecs-9200/9100 gtx950 series is an all-in-one integrated, rugged & compact, workstation-grade embedded system. Flexible lga1151 socket supports the workstation-grade intel ® xeon ® /core™ i7 processor (kaby lake-s/skylake-s) running with advanced in...

  • Page 9: 1.2   Features

    2 general introduction ©vecow ecs-9200/9100 gtx950 user manual 1.2 features • lga 1151 socket supports workstation-grade intel ® xeon ® /core™ i7 processor (kaby lake-s) with c236 chipset • nvidia geforce ® gtx 950 graphics engine supports nvidia pascal™ gpu architecture • multiple dvi-d, dvi-i, dis...

  • Page 10

    3 general introduction expansion mini pcie 3 full-size for pcie/usb/external sim card/msata m.2 1 m.2 socket (key id : m) graphics processor • intel ® hd graphics 630/530 • nvidia ® geforce ® gtx 950 interface 8 display interfaces : • 1 dvi-d : up to 1920 x1200 @ 60 hz • 2 dvi-i : up to 1920 x 1200 ...

  • Page 11

    4 general introduction ©vecow ecs-9200/9100 gtx950 user manual watchdog timer reset : 1 to 255 sec./min. Per step smart management wake on lan, pxe supported hw monitor monitoring temperature, voltages. Auto throttling control when cpu overheats. Software support os windows 10, windows 8.1, windows ...

  • Page 12

    5 general introduction i/o interface serial 4 com rs-232/422/485 w/auto flow control (esd 8kv) usb • 8 usb 3.0 (external) • 1 usb 2.0 (internal) isolated dio 32 isolated dio (16 di, 16 do) led power, hdd, wireless, poe sim card 3 external sim card socket expansion mini pcie 3 full-size for pcie/usb/...

  • Page 13

    6 general introduction ©vecow ecs-9200/9100 gtx950 user manual power input voltage 10v to 36v, dc-in power interface 3-pin terminal block : v+, v-, frame ground ignition control 16 mode (internal) remote switch 3-pin terminal block : on, off, ign surge protection up to 80v/1ms transient power others...

  • Page 14

    7 general introduction 1.3.3 specifications of ecs-9240 gtx950 system processor quad core 7th/6th generation intel ® xeon ® /core™ i7 processor (kaby lake-s/skylake-s) chipset intel ® c236 bios ami sio it8786e memory • ddr4 2133mhz • up to 32gb • 2 260-pin so-dimm socket (ecc/non-ecc) i/o interface ...

  • Page 15

    8 general introduction ©vecow ecs-9200/9100 gtx950 user manual ethernet lan 1 intel ® i219 gige lan supports iamt 11.0 lan 2 intel ® i210 gige lan poe lan 3 gige ieee 802.3at (25.5w/48v) poe + by intel ® i210 lan 4 gige ieee 802.3at (25.5w/48v) poe + by intel ® i210 lan 5 gige ieee 802.3at (25.5w/48...

  • Page 16

    9 general introduction storage temperature -40°c to 85°c (-40°f to 185°f) humidity 5% to 95% humidity, non-condensing relative humidity 95% at 60°c shock • iec 60068-2-27 • ssd : 50g @ wallmount, half-sine, 11ms vibration • iec 60068-2-64 • ssd : 5grms, 5hz to 500hz, 3 axis emc ce, fcc, en50155, en5...

  • Page 17

    10 general introduction ©vecow ecs-9200/9100 gtx950 user manual storage sata 2 sata iii support software raid 0, 1 msata 3 sata iii (mini pcie type, 6gbps) m2dom 1 pcie 3.0 (8gt/s) storage device • 1 cfast socket, push-in/push-out ejector • 2 front-access 2.5" ssd/hdd tray audio audio codec realtek ...

  • Page 18: 1.4   Supported Cpu List

    11 general introduction environment operating temperature 35w tdp cpu : xeon ® e3-1268l v5, core™ i7 : -40°c to 60°c (-40°f to 140°f) 65w tdp cpu : core™ i7 : -40°c to 55°c (-40°f to 131°f) 80w tdp cpu : xeon ® e3-1275 v6, e3-1275 v5, e3-1225 v5 : -40°c to 45°c (-40°f to 113°f) storage temperature -...

  • Page 19: 1.5   Mechanical Dimension

    12 general introduction ©vecow ecs-9200/9100 gtx950 user manual 1.5 mechanical dimension 1.5.1 dimensions of ecs-9204mx gtx950 155.0 (6.10”) 215.0 (8.46”) 260.0 (10.24”) 282.0 (11.10”) 297.0 (11.69”) 104.1 (4.10”) unit: mm (inch) 1.5.2 dimensions of ecs-9204m gtx950 155.0 (6.10”) 215.0 (8.46”) 260.0...

  • Page 20

    13 getting to know your ecs-9200/9100 gtx950 1.5.3 dimensions of ecs-9240 gtx950 260.0 (10.24”) 282.0 (11.10”) 297.0 (11.69”) 155.0 (6.10”) 215.0 (8.46”) 79.1 (3.1 1”) unit: mm (inch) 1.5.4 dimensions of ecs-9100 gtx950 260.0 (10.24”) 282.0 (11.10”) 297.0 (11.69”) 155.0 (6.10”) 215.0 (8.46”) 79.1 (3...

  • Page 21: 2.1   Packing List

    14 getting to know your ecs-9200/9100 gtx950 ©vecow ecs-9200/9100 gtx950 user manual 2 getting to know your ecs-9200/9100 gtx950 2.1 packing list item description qty 1 ecs-9200/9100 gtx950 embedded system (according to the configuration you order, the ecs-9200/9100 gtx950 series may contain ssd/hdd...

  • Page 22

    15 getting to know your ecs-9200/9100 gtx950 2.2 front panel i/o & functions in vecow ecs-9200/9100 gtx950 series family, all i/o connectors are located on the front panel and the rear panel. Most of the general connections to computer device, such as usb, lan jack, audio, display port, dvi-i, dvi-d...

  • Page 23

    16 getting to know your ecs-9200/9100 gtx950 ©vecow ecs-9200/9100 gtx950 user manual pin no. Description pin no. Description s1 gnd pc6 nc s2 sata_txp4 pc7 gnd s3 sata_txn4 pc8 cfast_led s4 gnd pc9 nc s5 sata_rxn4 pc10 nc s6 sata_rxp4 pc11 nc s7 gnd pc12 nc 2.2.3 cfast card there is a cfast socket o...

  • Page 24

    17 getting to know your ecs-9200/9100 gtx950 pin no. Description pin no. Description pc1 gnd pc13 +3.3v pc2 gnd pc14 +3.3v pc3 nc pc15 gnd pc4 nc pc16 gnd pc5 nc pc17 nc 2.2.4 pwr and hdd led indicator hdd led/yellow : a hard disk/ cfast led. If the led is on, it indicates that the system’s storage ...

  • Page 25

    18 getting to know your ecs-9200/9100 gtx950 ©vecow ecs-9200/9100 gtx950 user manual 2.2.7 displayport onboard display port supports auxiliary channel dual mode and the connection supports up to 4096 x 2304 resolution at 60 hz. Multi-stream transport display resolutions table as follows: rst dp lan ...

  • Page 26

    19 getting to know your ecs-9200/9100 gtx950 multi-stream transport display max. Resolution one panel display 4096x2304@60hz two panel displays concurrently 2880x1800@60hz three panel displays concurrently 2304x1440@60hz 2.2.8 usb 3.0 there are 4 usb 3.0 connections available supporting up to 5gb pe...

  • Page 27

    20 getting to know your ecs-9200/9100 gtx950 ©vecow ecs-9200/9100 gtx950 user manual 2.2.10 audio jack there are 2 audio connectors, mic-in and line-out, in the front side of ecs- 9200/9100 gtx950. Onboard realtek alc892 audio codec supports 5.1 channel hd audio and fully complies with intel high de...

  • Page 28

    21 getting to know your ecs-9200/9100 gtx950 2.2.11 wlan led, mini pcie, sim card comparison rst dp lan 1 lan 2 dvi-d dvi-i cfast sim 2 sim 3 sim 1 1 2 3 wlan mini pcie sim led mini pcie 1 sim 1 (cn12) 1 mini pcie 2 sim 2 (cn13) 2 mini pcie 3 sim 3 (cn11) 3 mini pcie slot/sim slot/wlan led mapping t...

  • Page 29

    22 getting to know your ecs-9200/9100 gtx950 ©vecow ecs-9200/9100 gtx950 user manual 2.2.12 ssd/hdd tray there are 2 front-access 2.5” ssd/hdd trays in the front side of ecs- 9200/9100 gtx950. Just trigger to open the ssd/ hdd tray, up to 4tb is available. Rst dp lan 1 lan 2 dvi-d dvi-i cfast sim 2 ...

  • Page 30

    23 getting to know your ecs-9200/9100 gtx950 2.3 rear panel i/o & functions 2.3.1 power terminal block it is a 3-pin power-on or power-off switch through phoenix contact terminal block. You could turn on or off the system power by using this contact. This terminal block supports dual functions of so...

  • Page 31

    24 getting to know your ecs-9200/9100 gtx950 ©vecow ecs-9200/9100 gtx950 user manual serial port pin no. Rs-232 rs-422 (5-wire) rs-422 (9-wire) rs-485 (3-wire) 1 to 4 1 dcd txd- txd- data- 2 rxd txd+ txd+ data+ 3 txd rxd+ rxd+ ----------- 4 dtr rxd- rxd- ----------- 5 gnd gnd gnd gnd 6 dsr ---------...

  • Page 32

    25 getting to know your ecs-9200/9100 gtx950 com3 & com 4 mb connector table: com port mb connector com port mb connector com 3 cn9 com 4 cn10 cn pin no. Signal name cn9 (com3) cn10 (com4) 1 chassis gnd 2 gnd 3 ri 4 dtr 5 cts 6 txd 7 rts 8 rxd 9 dsr 10 dcd com 3 & com 4 mb connector pin out: cn10 cn...

  • Page 33

    26 getting to know your ecs-9200/9100 gtx950 ©vecow ecs-9200/9100 gtx950 user manual 2.3.4 rear usb 3.0 there are 4 usb 3.0 connections available supporting up to 5gb per second data rate in the rear side of ecs-9200/9100 gtx950. It is also compliant with the requirements of super speed (ss), high s...

  • Page 34

    27 getting to know your ecs-9200/9100 gtx950 pin no. 10/ 100 mbps 1000 mbps poe 1 e_tx+ mdi0_p poe+ 2 e_tx- mdi0_n poe+ 3 e_rx+ mdi1_p poe- 4 ---- mdi2_p ---- 5 ----- mdi2_n ---- 6 e_rx- mdi1_n poe- 7 ----- mdi3_p ---- 8 ------ mdi3_n ---- each lan port is supported by standard rj-45 connector with ...

  • Page 36

    29 getting to know your ecs-9200/9100 gtx950 dio pin no. Definition function dio2 1 input 0 sio_gpi37 2 input 1 sio_gpi56 3 input 2 sio_gpi57 4 input 3 sio_gpi15 5 input 4 sio_gpi16 6 input 5 sio_gpi35 7 input 6 sio_gpi46 8 input 7 sio_gpi11 9 di2_com - 10 dio2_gnd - 11 output 0 sio_gpo22 12 output ...

  • Page 37

    30 getting to know your ecs-9200/9100 gtx950 ©vecow ecs-9200/9100 gtx950 user manual 2.3.7 4 of 5 independent displays you could have 4 independent displays as your wish from these 5 display ports. Also, you could have four 4k resolution displays, the 3 display port and a hdmi, from these 5 ports. C...

  • Page 38

    31 getting to know your ecs-9200/9100 gtx950 2.4 main board expansion connectors 2.4.1 inside view of ecs-9200/9100 gtx950 main board with connector location sata2 sata1 cn15 fan2 jp10 cn3 cn6 cn18 jp1 jp3 battery bios cn10 jp5 jp6 jp9 j4 j2 j9 j8 j7 j6 jp4 sw2 cn25 cn9 j1 fan1 jp2 mini pcie 3 mini ...

  • Page 39

    32 getting to know your ecs-9200/9100 gtx950 ©vecow ecs-9200/9100 gtx950 user manual 2.4.2 ups power connector for ups module optional, we use 4.2mm 2x2p power connector. This system has a ups power input connector for optional part ups module. Pin no. Definition pin no. Definition 1 ground 2 ground...

  • Page 40

    33 getting to know your ecs-9200/9100 gtx950 group pin no. Description hdd led 1 hdd_led_p 3 hdd_led_n reset button 5 fp_rst_btn_n 7 ground power led 2 pwr_led_p 4 pwr_led_n power button 6 fp_pwr_btn_in 8 ground 2.4.4 ddr4 slot there are 2 ddr4 channel onboard supporting ddr4 2133/1866 and up to 32g...

  • Page 41

    34 getting to know your ecs-9200/9100 gtx950 ©vecow ecs-9200/9100 gtx950 user manual 2.4.5 bios socket if the bios needs to be changed, please contact the vecow rma service team. 2.4.6 sata connector standard 7 pin sata connector there are 2 onboard high performance serial ata iii. It supports highe...

  • Page 42

    35 getting to know your ecs-9200/9100 gtx950 2.4.7 sata power header standard, all form factor 1x4p power header there are 2 hdd power header on board and each power header supports two 2.5” sata hdd. Pin no. Description pin no. Description 1 +v5 (max. 4a) 2 ground 3 ground 4 +v12 (max. 1.5a) j4 j2 ...

  • Page 43

    36 getting to know your ecs-9200/9100 gtx950 ©vecow ecs-9200/9100 gtx950 user manual pin no. Definition pin no. Definition 1 usb +vcc (+v5/max. 0.5a) 2 data- 3 data+ 4 ground 2.4.9 m2dom innodisk m2dom s20/s30 3me3 is a m.2 based disk module with vertical type form factor. Its mechanical design can ...

  • Page 44

    37 getting to know your ecs-9200/9100 gtx950 pin no. Function pin no. Function 75 gnd 73 gnd 74 +3.3v 71 gnd 72 +3.3v 69 pedet (nc-pcie/gnd- sata) 70 +3.3v 67 n/c 68 n/c mechanical key 57 gnd 58 n/c 55 refclkp 56 n/c 53 refclkn 54 wake# 51 gnd 52 clkreq# 49 petp0 /sata-a+ 50 perst# 47 petn0 /sata-a-...

  • Page 45

    38 getting to know your ecs-9200/9100 gtx950 ©vecow ecs-9200/9100 gtx950 user manual 31 perp1 32 n/c 29 pern1 30 n/c 27 gnd 28 n/c 25 petp2 26 n/c 23 petn2 24 n/c 21 gnd 22 n/c 19 perp2 20 n/c 17 pern2 18 +3.3v 15 gnd 16 +3.3v 13 petp3 14 +3.3v 11 petn3 12 +3.3v 9 gnd 10 das/dss# (i/o)/led1# (i)(0/3...

  • Page 46

    39 getting to know your ecs-9200/9100 gtx950 pin no. Function pin no. Function 51 reserved 52 +3.3vaux 49 reserved 50 gnd 47 reserved 48 +1.5v 45 reserved 46 reserved 43 gnd 44 reserved 41 +3.3vaux 42 reserved 39 +3.3vaux 40 gnd 37 gnd 38 usb_d+ 35 gnd 36 usb_d- 33 petp0 34 gnd 31 petn0 32 smb_data ...

  • Page 47

    40 getting to know your ecs-9200/9100 gtx950 ©vecow ecs-9200/9100 gtx950 user manual 2.4.12 rtc battery the system’s real-time clock is powered by a lithium battery. It is equipped with panasonic br2032 190mah lithium battery. It is recommended that you do not have to get the lithium battery on your...

  • Page 48

    41 getting to know your ecs-9200/9100 gtx950 pin no. Function pin no. Function 1 serirq 7 lframe# 2 +3.3v 8 lad0 3 la3 9 n/c 4 reset# 10 ground 5 lad1 11 clock 6 lad2 12 ground pin out: 2.4.14 lpc port 80 header ecs-9200/9100 gtx950 provides a lpc port 80 header for debug card. Cn3 2.4.15 lan ieee 1...

  • Page 49

    42 getting to know your ecs-9200/9100 gtx950 ©vecow ecs-9200/9100 gtx950 user manual pin no. Function pin no. Function 1 spd0 2 spd1 3 spd2 4 spd3 5 ground 6 ground pin out: 2.4.16 com port header ecs-9200/9100 gtx950 provides 4 com port headers for internal com port cable. Pin no. Description port ...

  • Page 50

    43 getting to know your ecs-9200/9100 gtx950 2.5 main board jumper & deep switch settings 2.5.1 top view of ecs-9200/9100 gtx950 main board with jumper and dip switch the figure below is the top view of ecs-9200/9100 gtx950 main board which is the main board. It shows the location of the jumpers and...

  • Page 51

    44 getting to know your ecs-9200/9100 gtx950 ©vecow ecs-9200/9100 gtx950 user manual you may configure your card to match the needs of your application by dip switch. As below show the dip switch on and off. On 1 2 1 : off 2 : off on 1 2 1 : on 2 : off on 1 2 1 : on 2 : on 2.5.2 usb power jumper jum...

  • Page 52

    45 getting to know your ecs-9200/9100 gtx950 2.5.3 com port ri pin select pin header pin no. Description com1 jp3 1-2 +5v (1a max.) 3-4 +12v (0.5a max.) 5-6 ri (default) pin header pin no. Description com2 jp4 1-2 +5v (1a max.) 3-4 +12v (0.5a max.) 5-6 ri (default) pin header pin no. Description com...

  • Page 53

    46 getting to know your ecs-9200/9100 gtx950 ©vecow ecs-9200/9100 gtx950 user manual 2.5.4 poe power on select jumper setting function jp10 1:2 poe power on at standby power ready jp10 2:3 poe power on after system power on (default) jp10 2.5.5 clear cmos/me switch jumper setting function jp1 1:2 *n...

  • Page 54: 2.6   Ignition Control

    47 getting to know your ecs-9200/9100 gtx950 2.6 ignition control 2.6.1 adjust ignition control modes ecs-9200/9100 gtx950 series provides ignition power control feature for in- vehicle applications. The built-in mcu monitors the ignition signal and turns on/ off the system according to pre-defined ...

  • Page 55

    48 getting to know your ecs-9200/9100 gtx950 ©vecow ecs-9200/9100 gtx950 user manual the modes are listed in the following table: item power on delay power off delay switch position 0 atx mode 1 no delay no delay 2 no delay 5 seconds 3 no delay 10 seconds 4 no delay 20 seconds 5 5 seconds 30 seconds...

  • Page 56

    49 getting to know your ecs-9200/9100 gtx950 2.6.2 ignition control wiring to activate ignition control, you need to provide ign signal via the 3-pin pluggable terminal block located in the back panel. It is below the general wiring configuration. For testing purpose, you can refer to the picture bl...

  • Page 57

    50 getting to know your ecs-9200/9100 gtx950 ©vecow ecs-9200/9100 gtx950 user manual 2.6.3 smart battery protection the system with “ignition control” can perform smart battery protection, namely low battery detection. When the system is running on a battery and its voltage drops below the threshold...

  • Page 58: System Setup

    51 hardware installation system setup 3.1 how to open your ecs-9200/9100 gtx950 3 step 1 remove hole plugs. Step 2 remove two f#6-32 screws (circled in red) and two f-m3 screws (circled in yellow) on the bottom side..

  • Page 59

    52 hardware installation ©vecow ecs-9200/9100 gtx950 user manual step 3 finish step1 and 2. Step 4 remove one khs#6-32x6 screw. Step 5 open the module..

  • Page 60

    53 hardware installation step 7 remove two f-#6-32 screws at the bottom side. Step 8 remove the cover. Remove one screw khs-#6-32 and ssd/ hdd tray at front panel. Step 6 finish..

  • Page 61

    54 hardware installation ©vecow ecs-9200/9100 gtx950 user manual step 9 remove ssd/hdd module. Step 10 be careful pulling out sata(yellow), power sata(blue) and com cables(red) . Step 11 remove four khs-#6-32 screws at the rear panel..

  • Page 62: 3.2   Installing Cpu

    55 hardware installation step 12 finish. 3.2 installing cpu step 1 remove one f #6-32 and pick up chock bracket. Step 2 remove eight ph-m3 and four m3x11 spring screws and pick up mother board..

  • Page 63

    56 hardware installation ©vecow ecs-9200/9100 gtx950 user manual step 4 open the cpu socket. (be careful cpu pins) step 3 cpu socket..

  • Page 64

    57 hardware installation step 6 finish. Step 5 install cpu on the socket. Step 7 close cpu socket and finish..

  • Page 65

    58 hardware installation ©vecow ecs-9200/9100 gtx950 user manual 3.3 installing ddr4 so-dimm modules step 1 ddr4 ram module into so-dimm slot. Step 2 make sure the ram module is locked by the memory slot..

  • Page 66

    59 hardware installation 3.4 installing mini pcie card step 1 install mini pcie card into the mini pcie socket. Step 2 fasten one m2.5 screw..

  • Page 67: 3.5   Installing Cfast Card

    60 hardware installation ©vecow ecs-9200/9100 gtx950 user manual 3.5 installing cfast card step 1 remove 2 pcs f-m3x4 screws on cfast & sim cards. Step 2 before inserting cfast & sim cards, make sure the system power is not plugged. Step 3 insert cfast card and push to lock. Step 4 insert cfast card...

  • Page 68: 3.6   Installing Sim Card

    61 hardware installation 3.6 installing sim card step 2 before inserting cfast & sim cards, make sure the system power is not plugged. Step 4 insert sim card and push to lock. Step 1 remove 2 pcs f-m3x4 screws on cfast & sim cards. Step 3 insert sim card and push to lock..

  • Page 69: 3.7   Installing Ssd/hdd

    62 hardware installation ©vecow ecs-9200/9100 gtx950 user manual 3.7 installing ssd/hdd step 1 trigger and open ssd/hdd tray. Step 2 insert 2.5” ssd/hdd in the tray and fasten two f-m3x4 screws..

  • Page 70

    63 hardware installation step 3 finish. Step 4 installing ssd/hdd..

  • Page 71: 3.8   Installing M.2

    64 hardware installation ©vecow ecs-9200/9100 gtx950 user manual 3.8 installing m.2 step 2 fasten one m3 screw. Step 1 m.2 slot..

  • Page 72: 3.9   Installing M2Dom

    65 hardware installation 3.9 installing m2dom step 2 m2dom module. Step 1 m2dom slot..

  • Page 73

    66 hardware installation ©vecow ecs-9200/9100 gtx950 user manual step 4 lock two m2 screws with slot. Step 3 install m2dom module with slot..

  • Page 74

    67 hardware installation 3.10 mounting your ecs-9200/9100 gtx950 step 1 ensure the screw holes on the right and left side of the upper case match the ones on ecs-9200/9100 gtx950 wall mount bracket. 3.10.1 wall mount bracket.

  • Page 75

    68 hardware installation ©vecow ecs-9200/9100 gtx950 user manual step 2 fasten 4pcs khs#6-32 screws and then finish. 3.10.2 vesa mount step 1 ecs-9200/9100 gtx950 and vesa mount..

  • Page 76

    69 hardware installation step 2 take ecs-9200/9100 gtx950 and vesa mount with fasten 4pcs khs#6-32 screws. Step 3 fasten four khs#6-32 screws and then finish..

  • Page 77

    70 hardware installation ©vecow ecs-9200/9100 gtx950 user manual step 4 finish. Step 5 there are two sizes of vesa, 75x75mm(red) and 100x100mm(yellow)..

  • Page 78

    71 hardware installation 3.10.3 din rail kit step 1 ecs-9200/9100 gtx950 and din rail kit. Step 2 take ecs-9200/9100 gtx950 and din rail kit and fasten four khs#6-32 screws in the four marked corners..

  • Page 79

    72 hardware installation ©vecow ecs-9200/9100 gtx950 user manual step 3 fasten four khs#6-32 screws and then finish. Step 4 finish. Step 5 ecs-9200/9100 gtx950 with din rail..

  • Page 80: Bios Setup

    73 bios and driver setting 4 bios setup 4.1 entering bios setup bios provides an interface for users to check and change system configuration. The bios setup program is accessed by pressing the key when post display output is shown. Figure 4-1: entering setup screen.

  • Page 81: 4.2   Main

    74 bios and driver setting ©vecow ecs-9200/9100 gtx950 user manual 4.2 main the main menu displays bios version and system information. There are two options on main menu, system date and system time. System date set the date. Use to switch between date elements. System time set the time. Use to swi...

  • Page 82

    75 bios and driver setting 4.3.1 acpi settings enable hibernation enables or disables system's ability to hibernate (os/s4 sleep state). This option may not be effective with some os. Acpi sleep state selects the highest acpi sleep state the system will enter when the suspend button is pressed. S3 v...

  • Page 83

    76 bios and driver setting ©vecow ecs-9200/9100 gtx950 user manual 4.3.3 pch-fw configuration me unconfig on rtc clear state disabling this option will cause me not to unconfigure on rtc clear. Me state set me to soft temporarily disabled. Figure 4 3-3: pch-fw settings 4.3.4 smart settings smart sel...

  • Page 84

    77 bios and driver setting serial port 3 configuration set parameters of serial port 3 (com 3). Serial port 4 configuration set parameters of serial port 4 (com 4). 4.3.7 serial port console redirection console redirection console redirection enable or disable. Console redirection settings the setti...

  • Page 85

    78 bios and driver setting ©vecow ecs-9200/9100 gtx950 user manual hyper-threading enabled for windows xp and linux (os optimized for hyper-threading technology) and disabled for other os (os not optimized for hyper-threading technology). When disabled, only one thread per core is enabled. Active pr...

  • Page 86

    79 bios and driver setting 4.3.9 intel txt information display intel txt information. Figure 4 3-9: intel txt information 4.3.10 sata configuration figure 4 3-10: sata devices settings cpu c state enable or disable cpu c states. Enhanced c-states enable/disable c1e. When enabled, cpu will switch to ...

  • Page 87

    80 bios and driver setting ©vecow ecs-9200/9100 gtx950 user manual sata controller(s) enable or disable sata device. Sata mode selection determines how sata controller(s) operate. Software feature mask configuration raid orom/rst driver will refer to the swfm configuration to enable or disable the s...

  • Page 88

    81 bios and driver setting 4.3.12 csm configuration csm support enable/disable csm support gatea20 active upon request - ga20 can be disabled using bios services. Always - do not allow ga20 to be disabled; this option is useful when any rt code is executed above 1mb. Option rom messages set display ...

  • Page 89

    82 bios and driver setting ©vecow ecs-9200/9100 gtx950 user manual 4.3.13 usb configuration legacy usb support enables legacy usb support. Auto option disables legacy support if no usb devices are connected. Disable option will keep usb devices available only for efi applications. Xhci hand-off this...

  • Page 90: 4.4   Chipset

    83 bios and driver setting vt-d vt-d capability. Gmm device (b0:d8:f0) enable/disable sa gmm device. Above 4gb mmio bios assignment enable/disable above 4gb memorymappedio bios assignment. This is disabled automatically when aperture size is set to 2048mb. 4.4.1 system agent (sa) configuration figur...

  • Page 91

    84 bios and driver setting ©vecow ecs-9200/9100 gtx950 user manual 4.4.2 graphics configuration of system agent (sa) gtt size select the gtt size. Aperture size select the aperture size. Note: above 4gb mmio bios assignment is automatically enabled when selecting 2048mb aperture. To use this feature...

  • Page 92

    85 bios and driver setting 4.4.4 memory information of system agent (sa) displays memory information. Figure 4-4-4: memory information 4.4.5 pch-io configuration figure 4-4-5: pch-io settings pch lan controller enable or disable onboard nic. Wake on lan enable or disable integrated lan to wake the s...

  • Page 93

    86 bios and driver setting ©vecow ecs-9200/9100 gtx950 user manual 4.4.6 pci express configuration of pch-io figure 4-4-6: pch-io settings dmi link aspm control enable/disable the control of active state power management on sa side of the dmi link. Native pcie enable pci express native support enabl...

  • Page 94

    87 bios and driver setting 4.4.8 sb porting configuration of pch-io sata raid rom legacy rom: legacy option rom uefi driver: uefi raid driver both: run the legacy option rom and uefi driver. Figure 4-4-8: raid rom settings 4.4.9 gpio manager configuration vga enable enable: vga display output enable...

  • Page 95: 4.5   Security

    88 bios and driver setting ©vecow ecs-9200/9100 gtx950 user manual set user password set hdd user password. *** advisable to power cycle system after setting hard disk passwords *** discard or save changes option in setup does not have any impact on hdd when password is set or removed. If the 'set h...

  • Page 96: 4.6   Boot

    89 bios and driver setting 4.6 boot figure 4-6: bios boot menu setup prompt timeout number of seconds to wait for setup activation key. 65535(0xffff) means indefinite waiting. Bootup numlock state select the keyboard numlock state. Quiet boot enables or disables quiet boot option. Boot option sets t...

  • Page 97: 4.7   Save & Exit

    90 bios and driver setting ©vecow ecs-9200/9100 gtx950 user manual 4.7 save & exit figure 4-7: bios save and exit menu save changes and exit exit system setup after saving the changes. Discard changes and exit exit system setup without saving any changes. Save changes and reset reset the system afte...

  • Page 98: A.1   Function Description

    91 appendix a a appendix a : isolated dio guide pin no. Definition description pin no. Definition description 1 ext_in0 di0 11 ext_out0 do0 2 ext_in1 di1 12 ext_out1 do1 3 ext_in2 di2 13 ext_out2 do2 4 ext_in3 di3 14 ext_out3 do3 5 ext_in4 di4 15 ext_out4 do4 6 ext_in5 di5 16 ext_out5 do5 7 ext_in6 ...

  • Page 99: A.2   Dio Signal Circuit

    92 ©vecow ecs-9200/9100 gtx950 user manual appendix a a.2 dio signal circuit di reference circuit: sink mode (npn) v+ v- power supply 6-48v dc di_com (pin 9) di (pin1-8) dio connector source mode (pnp) v+ v- power supply 6-48v dc di_com (pin 9) di (pin1-8) dio connector do reference circuit: v+ io v...

  • Page 100: A.4   Dio Demo Tool

    93 appendix a this driver support to 32bit and 64bit version that are windows 7 above. Please make sure you os before you install it. A.4 dio demo tool execute dio demo tool (ecs9k2.Exe). Operation on dio / wdt / poe demo tool utility. Click “isolate” checked button for isolate / non-isolated dio se...

  • Page 101: B.1   Ecs9K2.Dll Api

    94 ©vecow ecs-9200/9100 gtx950 user manual appendix b b appendix b : software functions b.1 ecs9k2.Dll api in runtime folder, on ecs9k2.H: bool initial(byte isolate_type, byte dio_npn); install driver and initial machine for dio access isolate_type: dio isolate type 1: isolated dio; 0: non-isolated ...

  • Page 102

    95 appendix b bool setdo2(byte do); set dio2 output do: dio2 output (do[7:0]) return: true (1): success; false (0): fail (driver not work, or hardware problem) bool getdo2(byte *do); get dio2 output do: dio2 output (do[7:0]) return: true (1): success; false (0): fail (driver not work, or hardware pr...

  • Page 103

    96 ©vecow ecs-9200/9100 gtx950 user manual appendix b bool setpoe(byte poe); set poe on/off setup poe: poe switch (poe[7:0]) return: true (1): success; false (0): fail (driver not work, or hardware problem) bool getdio1config(byte *isolate_type, byte *di_npn, byte *do_ npn); get dio1 configuration i...

  • Page 104

    97 appendix c bool set dio2config(byte isolate_type, byte di_npn, byte do_npn); set dio2 configuration isolate_type: dio2 isolate type 1: isolated dio; 0: non-isolated dio di_npn: dio2 input npn mode (di_npn[7:0]) 1: pnp (source) mode for european rule; 0: npn (sink) mode for japanese rule do_npn: d...

  • Page 105: C.1   Sata Mode For Raid

    98 ©vecow ecs-9200/9100 gtx950 user manual appendix c c appendix c : raid installation guide c.1 sata mode for raid please select sata device to raid mode on bios menu. Advanced → sata configuration → sata mode selection c.2 os installation ecs-9200/9100 gtx950 is featured with six sata, include two...

  • Page 106: Technology” Software

    99 appendix c c.4 install “intel rapid storage technology” software you can get the software on ecs-9200/9100 gtx950 driver cd. Also, you can find latest information and software directly from intel website. Http://www.Intel.Com/p/en_us/support/highlights/chpsts/imsm the raid environment has been do...

  • Page 107

    100 ©vecow ecs-9200/9100 gtx950 user manual appendix c then add “logical device” for windows access. C.7 disk management : partition the disk after raid 1 volume created, you can see the figure of sata device allocation. To start disk management tool, select "initialize disk." you will find “volume_...

  • Page 108: Different

    101 appendix c c.10 recovery and auto re-build when using different raid hdd there is a warning will pop-up to ask you if the disk is not a member of original raid volume. If you press “rebuild”, it will replace the broken sata hdd to the last one sata hdd of raid volume. C.9 recovery and auto re-bu...

  • Page 109

    102 ©vecow ecs-9200/9100 gtx950 user manual appendix d d appendix d : power consumption testing board ecs-9200 gtx950 ram 8gb x 2 usb-1 usb keyboard logitech k120 usb-2 usb mouse microsoft 1113 usb-3 usb flash transecnd 3.0 8gb usb-4 usb flash transecnd 3.0 8gb cfast innodisk cfast 3me3 64gb sata 0 ...

  • Page 110

    103 appendix d d.1 intel® core™ i7-6700 (8m cache, up to 4.00 ghz) cpu power input sleep mode idle status : cpu usage less 3% max current max consumption max current max consumption core™ i7- 6700 15v 0.296a 04.44w 1.794a 26.91w core™ i7- 6700 24v 0.214a 05.14w 1.183a 28.39w core™ i7- 6700 36v 0.239...

  • Page 111: Storage List

    104 ©vecow ecs-9200/9100 gtx950 user manual appendix e e appendix e : supported memory & storage list testing board ecs-9200 gtx950 memory test version: 5.1 burnintest v8.1 e.1 supported memory list channel memory test burn in flash bios remove battery *2 pass pass pass pass *1(socket 1) pass pass n...

  • Page 112: E.3   Non-Ecc

    105 appendix e brand info note & s test temp. (celsius) kingston 16gb 2rx8 2gx64-bit pc4-2133 kvr21s15d8/16 bkmm1641607 25ºc bkmm1661618 25ºc memxpro 4gb ddr4-2133-15 wild temp. D4s4ghiofei 01611170040001 25ºc 01611170040002 25ºc memxpro 8gb ddr4-2133-15 wild temp. D4s8ghioffi 01611150020001 25ºc ...

  • Page 113

    106 ©vecow ecs-9200/9100 gtx950 user manual appendix e type brand model capacity msata intel intel-310 ssdmaemc080g2 80gb silicon power sp128gimsa301sw0 128gb sata ssd transcend ssd370 ts64gssd370 64gb memxpro ssd m3a mi3ma1212802wn 128gb ssd m3a mi3ma1225604wn 256gb ssd m3a mi3ma1251208wn 512gb inn...

  • Page 114

    107 appendix f ** if more help is needed, please contact vecow technical support ** f appendix f : graphics performance test temperature (based on 95% humidity) 30ºc 35ºc 40ºc 45ºc 50ºc 55ºc 60ºc 3dmark 11 (v1.5.5.0) score x2689 x2686 x2653 x2525 x2381 x2324 x2314 resolution 1920 x 1080 highest temp...

  • Page 115

    For further support information, please visit www.Vecow.Com this document is released for reference purpose only. All product offerings and specifications are subject to change without prior notice. No part of this publication may be reproduced in any form or by any means, electric, photocopying, or...