1. DL manuals
  2. Vecow
  3. Desktop
  4. ECS-9100-GTX1050
  5. User Manual

Vecow ECS-9100-GTX1050 User Manual

Manual is about: ECS-9200/9100 Series, Quad Core Intel Xeon / Core i7 Processor Embedded System with Intel C236 Chipset & NVIDIA GEFORCE GTX 1050 Ti / 1050 Graphics High Performance, Independent Graphics, EN50155

Summary of ECS-9100-GTX1050

  • Page 1

    User manual user manual 1.1.0 edition 20171103 ecs-9200/9100 gtx1050 quad core intel ® xeon ® / core ™ i7 processor embedded system with intel ® c236 chipset & nvidia geforce ® gtx 1050 ti/1050 graphics high performance, independent graphics, en50155.

  • Page 2: Record of Revision

    Ii version date page description remark 1.0 07/25/2017 all official release 1.1 11/03/2017 46-66 update record of revision.

  • Page 3: Fcc

    Iii this manual is released by vecow co., ltd. For reference purpose only. All product offerings and specifications are subject to change without prior notice. It does not represent commitment of vecow co., ltd. Vecow shall not be liable for direct, indirect, special, incidental, or consequential da...

  • Page 4: Order Information

    Iv part number description ecs-9240- gtx1050t ecs-9200, nvidia geforce ® gtx 1050 ti, 6 gige lan w/4 poe + , 2 ssd tray, 8 usb 3.0, 4 com, 1 m.2, 1 m2dom, 3 sim, 32 isolated dio ecs-9240- gtx1050 ecs-9200, nvidia geforce ® gtx 1050, 6 gige lan w/4 poe + , 2 ssd tray, 8 usb 3.0, 4 com, 1 m.2, 1 m2dom...

  • Page 5: Order Accessories

    V part number description e3-1275 v6 7th generation intel ® xeon ® e3-1275 v6 processor (8m cache, up to 4.20 ghz, 80w) e3-1275 v5 6th generation intel ® xeon ® e3-1275 v5 processor (8m cache, up to 4.00 ghz, 80w) e3-1225 v5 6th generation intel ® xeon ® e3-1225 v5 processor (6m cache, up to 3.70 gh...

  • Page 6: Table of Contents

    Vi table of contents chapter 1 general introduction 1 1.1 overview 1 1.2 features 2 1.3 product specification 2 1.3.1 specifications of ecs-9240 gtx1050 2 1.3.2 specifications of ecs-9100 gtx1050 5 1.4 supported cpu list 7 1.5 mechanical dimension 8 1.5.1 dimensions of ecs-9240 gtx1050 8 1.5.2 dimen...

  • Page 7: Chapter   4

    Vii 3.7 installing ssd/hdd 57 3.8 installing m.2 59 3.9 installing m2dom 60 3.10 mounting your ecs-9200/9100 gtx1050 62 chapter 4 bios setup 67 4.1 entering bios setup 67 4.2 main 68 4.3 advanced 68 4.4 chipset 77 4.5 security 82 4.6 boot 83 4.7 save & exit 84 appendix a : isolated dio guide 85 appe...

  • Page 8: General Introduction

    1 general introduction 1 general introduction 1.1 overview vecow ecs-9200/9100 gtx1050 series is a workstation-grade compact integrated embedded system. Flexible lga1151 socket supports the workstation- grade intel ® xeon ® /core™ i7 processor (kaby lake-s/skylake-s) running with advanced intel ® c2...

  • Page 9: 1.2   Features

    2 general introduction ©vecow ecs-9200/9100 gtx1050 user manual 1.2 features • lga 1151 socket supports workstation-grade intel ® xeon ® /core™ i7 processor (kaby lake/skylake) with c236 chipset • nvidia geforce ® gtx 1050 graphics engine supports nvidia pascal™ gpu architecture, up to 8k resolution...

  • Page 10

    3 general introduction expansion mini pcie 3 full-size for pcie/usb/external sim card/msata m.2 1 m.2 socket (key id : m) graphics processor • intel ® hd graphics 630/530 • nvidia ® geforce ® gtx 1050 ti/gtx 1050 interface 6 display interfaces : • 3 dvi : up to 1920 x1200 @ 60 hz • 1 displayport : u...

  • Page 11

    4 general introduction ©vecow ecs-9200/9100 gtx1050 user manual others tpm optional infineon slb9665 supports tpm 2.0, lpc interface watchdog timer reset : 1 to 255 sec./min. Per step smart management wake on lan, pxe supported hw monitor monitoring temperature, voltages. Auto throttling control whe...

  • Page 12

    5 general introduction 1.3.2 specifications of ecs-9100 gtx1050 system processor quad core 7th/6th generation intel ® xeon ® /core™ i7 processor (kaby lake-s/skylake-s) chipset intel ® c236 bios ami sio it8786e memory • ddr4 2133mhz • up to 32gb • 2 260-pin so-dimm socket (ecc/non-ecc) i/o interface...

  • Page 13

    6 general introduction ©vecow ecs-9200/9100 gtx1050 user manual lan 1 intel ® i219 gige lan supports iamt 11.0 lan 2 intel ® i210 gige lan power input voltage 10v to 36v, dc-in power interface 3-pin terminal block : v+, v-, frame ground ignition control 16 mode (internal) remote switch 3-pin termina...

  • Page 14: 1.4   Supported Cpu List

    7 general introduction 1.4 supported cpu list processor no. Tdp cache max. Frequency embedded xeon ® e3-1575m v5 45w 8m up to 3.00 ghz xeon ® e3-1545m v5 45w 8m up to 2.90 ghz xeon ® e3-1535m v5 45w 8m up to 2.80 ghz xeon ® e3-1515m v5 45w 8m up to 2.80 ghz xeon ® e3-1505m v5 45w 8m up to 2.80 ghz y...

  • Page 15: 1.5   Mechanical Dimension

    8 general introduction ©vecow ecs-9200/9100 gtx1050 user manual 1.5 mechanical dimension 1.5.1 dimensions of ecs-9240 gtx1050 260.0 (10.24”) 282.0 (11.10”) 297.0 (11.69”) 155.0 (6.10”) 215.0 (8.46”) 79.1 (3.1 1”) 99.1 (3.90”) unit: mm (inch) 1.5.2 dimensions of ecs-9100 gtx1050 260.0 (10.24”) 282.0 ...

  • Page 16: 2.1   Packing List

    9 getting to know your ecs-9200/9100 gtx1050 2 getting to know your ecs-9200/9100 gtx1050 2.1 packing list item description qty 1 ecs-9200/9100 gtx1050 embedded system (according to the configuration you order, ecs-9200/9100 gtx1050 series may contain ssd/hdd and ddr4 so-dimm. Please verify these it...

  • Page 17

    10 getting to know your ecs-9200/9100 gtx1050 ©vecow ecs-9200/9100 gtx1050 user manual 2.2 front panel i/o & functions in vecow ecs-9200/9100 gtx1050 series family, all i/o connectors are located on the front panel and the rear panel. Most of the general connections to computer device, such as usb, ...

  • Page 18

    11 getting to know your ecs-9200/9100 gtx1050 pin no. Description pin no. Description s1 gnd pc6 nc s2 sata_txp4 pc7 gnd s3 sata_txn4 pc8 cfast_led s4 gnd pc9 nc s5 sata_rxn4 pc10 nc s6 sata_rxp4 pc11 nc s7 gnd pc12 nc 2.2.3 cfast card there is a cfast socket on the front panel supporting type-i/ii ...

  • Page 19

    12 getting to know your ecs-9200/9100 gtx1050 ©vecow ecs-9200/9100 gtx1050 user manual pin no. Description pin no. Description pc1 gnd pc13 +3.3v pc2 gnd pc14 +3.3v pc3 nc pc15 gnd pc4 nc pc16 gnd pc5 nc pc17 nc 2.2.4 pwr and hdd led indicator hdd led/yellow : a hard disk/ cfast led. If the led is o...

  • Page 20

    13 getting to know your ecs-9200/9100 gtx1050 2.2.7 displayport onboard display port supports auxiliary channel dual mode and the connection supports up to 4096 x 2304 resolution at 60 hz. Multi-stream transport display resolutions table as follows: rst dp lan 1 lan 2 dvi-d dvi-i cfast sim 2 sim 3 s...

  • Page 21

    14 getting to know your ecs-9200/9100 gtx1050 ©vecow ecs-9200/9100 gtx1050 user manual multi-stream transport display max. Resolution one panel display 4096x2304@60hz two panel displays concurrently 2880x1800@60hz three panel displays concurrently 2304x1440@60hz 2.2.8 usb 3.0 there are 4 usb 3.0 con...

  • Page 22

    15 getting to know your ecs-9200/9100 gtx1050 2.2.10 audio jack there are 2 audio connectors, mic-in and line-out, in the front side of ecs- 9200/9100 gtx1050. Onboard realtek alc892 audio codec supports 5.1 channel hd audio and fully complies with intel high definition audio (azalia) specifications...

  • Page 23

    16 getting to know your ecs-9200/9100 gtx1050 ©vecow ecs-9200/9100 gtx1050 user manual 2.2.11 wlan led, mini pcie, sim card comparison rst dp lan 1 lan 2 dvi-d dvi-i cfast sim 2 sim 3 sim 1 1 2 3 wlan mini pcie sim led mini pcie 1 sim 1 (cn12) 1 mini pcie 2 sim 2 (cn13) 2 mini pcie 3 sim 3 (cn11) 3 ...

  • Page 24

    17 getting to know your ecs-9200/9100 gtx1050 2.2.12 ssd/hdd tray there are 2 front-access 2.5” ssd/hdd trays in the front side of ecs- 9200/9100 gtx1050. Just trigger to open the ssd/ hdd tray, up to 4tb is available. Rst dp lan 1 lan 2 dvi-d dvi-i cfast sim 2 sim 3 sim 1 1 2 3 wlan hdd 1 hdd 2 2.2...

  • Page 25

    18 getting to know your ecs-9200/9100 gtx1050 ©vecow ecs-9200/9100 gtx1050 user manual 2.3 rear panel i/o & functions 2.3.1 power terminal block it is a 3-pin power-on or power-off switch through phoenix contact terminal block. You could turn on or off the system power by using this contact. This te...

  • Page 26

    19 getting to know your ecs-9200/9100 gtx1050 serial port pin no. Rs-232 rs-422 (5-wire) rs-422 (9-wire) rs-485 (3-wire) 1 to 4 1 dcd txd- txd- data- 2 rxd txd+ txd+ data+ 3 txd rxd+ rxd+ ----------- 4 dtr rxd- rxd- ----------- 5 gnd gnd gnd gnd 6 dsr ----------- rts- ----------- 7 rts ----------- r...

  • Page 27

    20 getting to know your ecs-9200/9100 gtx1050 ©vecow ecs-9200/9100 gtx1050 user manual com 3 & com 4 mb connector table: com port mb connector com port mb connector com 3 cn9 com 4 cn10 cn pin no. Signal name cn9 (com3) cn10 (com4) 1 chassis gnd 2 gnd 3 ri 4 dtr 5 cts 6 txd 7 rts 8 rxd 9 dsr 10 dcd ...

  • Page 28

    21 getting to know your ecs-9200/9100 gtx1050 2.3.4 rear usb 3.0 there are 4 usb 3.0 connections available supporting up to 5gb per second data rate in the rear side of ecs-9200/9100 gtx1050. It is also compliant with the requirements of super speed (ss), high speed (hs), full speed (fs) and low spe...

  • Page 29

    22 getting to know your ecs-9200/9100 gtx1050 ©vecow ecs-9200/9100 gtx1050 user manual pin no. 10/ 100 mbps 1000 mbps poe 1 e_tx+ mdi0_p poe+ 2 e_tx- mdi0_n poe+ 3 e_rx+ mdi1_p poe- 4 ---- mdi2_p ---- 5 ----- mdi2_n ---- 6 e_rx- mdi1_n poe- 7 ----- mdi3_p ---- 8 ------ mdi3_n ---- each lan port is s...

  • Page 31

    24 getting to know your ecs-9200/9100 gtx1050 ©vecow ecs-9200/9100 gtx1050 user manual dio pin no. Definition function dio2 1 input 0 sio_gpi37 2 input 1 sio_gpi56 3 input 2 sio_gpi57 4 input 3 sio_gpi15 5 input 4 sio_gpi16 6 input 5 sio_gpi35 7 input 6 sio_gpi46 8 input 7 sio_gpi11 9 di2_com - 10 d...

  • Page 33

    26 getting to know your ecs-9200/9100 gtx1050 ©vecow ecs-9200/9100 gtx1050 user manual 2.4 main board expansion connectors 2.4.1 inside view of ecs-9200/9100 gtx1050 main board with connector location sata2 sata1 cn15 fan2 jp10 cn3 cn6 cn18 jp1 jp3 battery bios cn10 jp5 jp6 jp9 j4 j2 j9 j8 j7 j6 jp4...

  • Page 34

    27 getting to know your ecs-9200/9100 gtx1050 2.4.2 ups power connector for ups module optional, we use 4.2mm 2x2p power connector. This system has a ups power input connector for optional part ups module. Pin no. Definition pin no. Definition 1 ground 2 ground 3 +vdc_in (6~36v, max.8a) 4 +vdc_in (6...

  • Page 35

    28 getting to know your ecs-9200/9100 gtx1050 ©vecow ecs-9200/9100 gtx1050 user manual group pin no. Description hdd led 1 hdd_led_p 3 hdd_led_n reset button 5 fp_rst_btn_n 7 ground power led 2 pwr_led_p 4 pwr_led_n power button 6 fp_pwr_btn_in 8 ground 2.4.4 ddr4 slot there are 2 ddr4 channel onboa...

  • Page 36

    29 getting to know your ecs-9200/9100 gtx1050 2.4.5 bios socket if the bios needs to be changed, please contact the vecow rma service team. 2.4.6 sata connector standard 7 pin sata connector there are 2 onboard high performance serial ata iii. It supports higher storage capacity with less cabling ef...

  • Page 37

    30 getting to know your ecs-9200/9100 gtx1050 ©vecow ecs-9200/9100 gtx1050 user manual 2.4.7 sata power header standard, all form factor 1x4p power header there are 2 hdd power header on board and each power header supports two 2.5” sata hdd. Pin no. Description pin no. Description 1 +v5 (max. 4a) 2...

  • Page 38

    31 getting to know your ecs-9200/9100 gtx1050 pin no. Definition pin no. Definition 1 usb +vcc (+v5/max. 0.5a) 2 data- 3 data+ 4 ground 2.4.9 m2dom innodisk m2dom s20/s30 3me3 is a m.2 based disk module with vertical type form factor. Its mechanical design can help board maker to release up to 90% s...

  • Page 39

    32 getting to know your ecs-9200/9100 gtx1050 ©vecow ecs-9200/9100 gtx1050 user manual pin no. Function pin no. Function 75 gnd 73 gnd 74 +3.3v 71 gnd 72 +3.3v 69 pedet (nc-pcie/gnd- sata) 70 +3.3v 67 n/c 68 n/c mechanical key 57 gnd 58 n/c 55 refclkp 56 n/c 53 refclkn 54 wake# 51 gnd 52 clkreq# 49 ...

  • Page 40

    33 getting to know your ecs-9200/9100 gtx1050 31 perp1 32 n/c 29 pern1 30 n/c 27 gnd 28 n/c 25 petp2 26 n/c 23 petn2 24 n/c 21 gnd 22 n/c 19 perp2 20 n/c 17 pern2 18 +3.3v 15 gnd 16 +3.3v 13 petp3 14 +3.3v 11 petn3 12 +3.3v 9 gnd 10 das/dss# (i/o)/led1# (i)(0/3.3v) 7 perp3 8 n/c 5 pern3 6 n/c 3 gnd ...

  • Page 41

    34 getting to know your ecs-9200/9100 gtx1050 ©vecow ecs-9200/9100 gtx1050 user manual pin no. Function pin no. Function 51 reserved 52 +3.3vaux 49 reserved 50 gnd 47 reserved 48 +1.5v 45 reserved 46 reserved 43 gnd 44 reserved 41 +3.3vaux 42 reserved 39 +3.3vaux 40 gnd 37 gnd 38 usb_d+ 35 gnd 36 us...

  • Page 42

    35 getting to know your ecs-9200/9100 gtx1050 2.4.12 rtc battery the system’s real-time clock is powered by a lithium battery. It is equipped with panasonic br2032 190mah lithium battery. It is recommended that you do not have to get the lithium battery on your own. If the battery needs to be change...

  • Page 43

    36 getting to know your ecs-9200/9100 gtx1050 ©vecow ecs-9200/9100 gtx1050 user manual pin no. Function pin no. Function 1 serirq 7 lframe# 2 +3.3v 8 lad0 3 la3 9 n/c 4 reset# 10 ground 5 lad1 11 clock 6 lad2 12 ground pin out: 2.4.14 lpc port 80 header ecs-9200/9100 gtx1050 provides a lpc port 80 h...

  • Page 44

    37 getting to know your ecs-9200/9100 gtx1050 pin no. Function pin no. Function 1 spd0 2 spd1 3 spd2 4 spd3 5 ground 6 ground pin out: 2.4.16 com port header ecs-9200/9100 gtx1050 provides 4 com port headers for internal com port cable. Pin no. Description port 1 ground_frame com3 2 ground com3 3 ri...

  • Page 45

    38 getting to know your ecs-9200/9100 gtx1050 ©vecow ecs-9200/9100 gtx1050 user manual 2.5 main board jumper & deep switch settings 2.5.1 top view of ecs-9200/9100 gtx1050 main board with jumper and dip switch the figure below is the top view of ecs-9200/9100 gtx1050 main board which is the main boa...

  • Page 46

    39 getting to know your ecs-9200/9100 gtx1050 you may configure your card to match the needs of your application by dip switch. As below show the dip switch on and off. On 1 2 1 : off 2 : off on 1 2 1 : on 2 : off on 1 2 1 : on 2 : on 2.5.2 usb power jumper jumper setting function jp9 1:2 supported ...

  • Page 47

    40 getting to know your ecs-9200/9100 gtx1050 ©vecow ecs-9200/9100 gtx1050 user manual 2.5.3 com port ri pin select pin header pin no. Description com1 jp3 1-2 +5v (1a max.) 3-4 +12v (0.5a max.) 5-6 ri (default) pin header pin no. Description com2 jp4 1-2 +5v (1a max.) 3-4 +12v (0.5a max.) 5-6 ri (d...

  • Page 48

    41 getting to know your ecs-9200/9100 gtx1050 2.5.4 poe power on select jumper setting function jp10 1:2 poe power on at standby power ready jp10 2:3 poe power on after system power on (default) jp10 2.5.5 clear cmos/me switch jumper setting function jp1 1:2 *normal(default) jp1 2:3 clear cmos jumpe...

  • Page 49: 2.6   Ignition Control

    42 getting to know your ecs-9200/9100 gtx1050 ©vecow ecs-9200/9100 gtx1050 user manual 2.6 ignition control 2.6.1 adjust ignition control modes ecs-9200/9100 gtx1050 series provides ignition power control feature for in- vehicle applications. The built-in mcu monitors the ignition signal and turns o...

  • Page 50

    43 getting to know your ecs-9200/9100 gtx1050 the modes are listed in the following table: item power on delay power off delay switch position 0 atx mode 1 no delay no delay 2 no delay 5 seconds 3 no delay 10 seconds 4 no delay 20 seconds 5 5 seconds 30 seconds 6 5 seconds 60 seconds 7 5 seconds 90 ...

  • Page 51

    44 getting to know your ecs-9200/9100 gtx1050 ©vecow ecs-9200/9100 gtx1050 user manual 2.6.2 ignition control wiring to activate ignition control, you need to provide ign signal via the 3-pin pluggable terminal block located in the back panel. It is below the general wiring configuration. For testin...

  • Page 52

    45 getting to know your ecs-9200/9100 gtx1050 2.6.3 smart battery protection the system with “ignition control” can perform smart battery protection, namely low battery detection. When the system is running on a battery and its voltage drops below the threshold, the system will automatically shut do...

  • Page 53: System Setup

    46 hardware installation ©vecow ecs-9200/9100 gtx1050 user manual system setup 3.1 how to open your ecs-9200/9100 gtx1050 3 step 1 remove hole plugs. Step 2 remove two f#6-32 screws (circled in red) and two f-m3 screws (circled in yellow) on the bottom side..

  • Page 54

    47 hardware installation step 3 finish step1 and 2. Step 4 remove one khs#6-32x6 screw. Step 5 open the module..

  • Page 55

    48 hardware installation ©vecow ecs-9200/9100 gtx1050 user manual step 7 remove two f-#6-32 screws at the bottom side. Step 8 remove the cover. Remove one screw khs-#6-32 and ssd/ hdd tray at front panel. Step 6 finish..

  • Page 56

    49 hardware installation step 9 remove ssd/hdd module. Step 10 be careful pulling out sata(yellow), power sata(blue) and com cables(red). Step 11 remove four khs-#6-32 screws at the rear panel..

  • Page 57: 3.2   Installing Cpu

    50 hardware installation ©vecow ecs-9200/9100 gtx1050 user manual step 12 finish. 3.2 installing cpu step 1 remove one f #6-32 and pick up chock bracket. Step 2 remove eight ph-m3 and four m3x11 spring screws and pick up mother board..

  • Page 58

    51 hardware installation step 4 open the cpu socket. (be careful cpu pins) step 3 cpu socket..

  • Page 59

    52 hardware installation ©vecow ecs-9200/9100 gtx1050 user manual step 6 finish. Step 5 install cpu on the socket. Step 7 close cpu socket and finish..

  • Page 60

    53 hardware installation 3.3 installing ddr4 so-dimm modules step 1 ddr4 ram module into so-dimm slot. Step 2 make sure the ram module is locked by the memory slot..

  • Page 61

    54 hardware installation ©vecow ecs-9200/9100 gtx1050 user manual 3.4 installing mini pcie card step 1 install mini pcie card into the mini pcie socket. Step 2 fasten one m2.5 screw..

  • Page 62: 3.5   Installing Cfast Card

    55 hardware installation 3.5 installing cfast card step 1 remove 2 pcs f-m3x4 screws on cfast & sim cover. Step 2 before inserting cfast & sim cards, make sure the system power is not plugged. Step 3 insert cfast card and push to lock. Step 4 finish..

  • Page 63: 3.6   Installing Sim Card

    56 hardware installation ©vecow ecs-9200/9100 gtx1050 user manual 3.6 installing sim card step 2 before inserting cfast & sim cards, make sure the system power is not plugged. Step 4 finish. Step 1 remove 2 pcs f-m3x4 screws on cfast & sim cover. Step 3 insert sim card and push to lock..

  • Page 64: 3.7   Installing Ssd/hdd

    57 hardware installation 3.7 installing ssd/hdd step 1 trigger and open ssd/hdd tray. Step 2 insert 2.5” ssd/hdd in the tray and fasten two f-m3x4 screws..

  • Page 65

    58 hardware installation ©vecow ecs-9200/9100 gtx1050 user manual step 3 finish. Step 4 install ssd/hdd..

  • Page 66: 3.8   Installing M.2

    59 hardware installation 3.8 installing m.2 step 2 fasten one m3 screw. Step 1 m.2 slot..

  • Page 67: 3.9   Installing M2Dom

    60 hardware installation ©vecow ecs-9200/9100 gtx1050 user manual 3.9 installing m2dom step 2 m2dom module. Step 1 m2dom slot..

  • Page 68

    61 hardware installation step 4 lock two m2 screws with slot. Step 3 install m2dom module with slot..

  • Page 69

    62 hardware installation ©vecow ecs-9200/9100 gtx1050 user manual 3.10 mounting your ecs-9200/9100 gtx1050 step 1 ensure the screw holes on the right and left sides of the upper case match the ones on ecs-9200/9100 gtx1050 wall mount bracket. 3.10.1 wall mount bracket step 2 fasten 4pcs khs#6-32 scr...

  • Page 70

    63 hardware installation 3.10.2 vesa mount step 1 ecs-9200/9100 gtx1050 and vesa mount. Step 2 take ecs-9200/9100 gtx1050 and vesa mount with fasten 4pcs khs#6-32 screws..

  • Page 71

    64 hardware installation ©vecow ecs-9200/9100 gtx1050 user manual step 3 fasten four khs#6-32 screws and then finish. Step 4 finish. Step 5 there are two sizes of vesa, 75x75mm(red) and 100x100mm(yellow)..

  • Page 72

    65 hardware installation 3.10.3 din rail kit step 1 ecs-9200/9100 gtx1050 and din rail kit. Step 2 take ecs-9200/9100 gtx1050 and din rail kit and fasten four khs#6-32 screws in the four marked corners..

  • Page 73

    66 hardware installation ©vecow ecs-9200/9100 gtx1050 user manual step 3 fasten four khs#6-32 screws and then finish. Step 4 finish. Step 5 ecs-9200/9100 gtx1050 with din rail..

  • Page 74: Bios Setup

    67 bios and driver setting 4 bios setup 4.1 entering bios setup bios provides an interface for users to check and change system configuration. The bios setup program is accessed by pressing the key when post display output is shown. Figure 4-1: entering setup screen.

  • Page 75: 4.2   Main

    68 bios and driver setting ©vecow ecs-9200/9100 gtx1050 user manual 4.2 main the main menu displays bios version and system information. There are two options on main menu, system date and system time. System date set the date. Use to switch between date elements. System time set the time. Use to sw...

  • Page 76

    69 bios and driver setting 4.3.1 acpi settings enable hibernation enables or disables system's ability to hibernate (os/s4 sleep state). This option may not be effective with some os. Acpi sleep state selects the highest acpi sleep state the system will enter when the suspend button is pressed. S3 v...

  • Page 77

    70 bios and driver setting ©vecow ecs-9200/9100 gtx1050 user manual 4.3.3 pch-fw configuration me unconfig on rtc clear state disabling this option will cause me not to unconfigure on rtc clear. Me state set me to soft temporarily disabled. Figure 4 3-3: pch-fw settings 4.3.4 smart settings smart se...

  • Page 78

    71 bios and driver setting 4.3.7 serial port console redirection console redirection console redirection enable or disable. Console redirection settings the settings specify how the host computer and the remote computer (which the user is using) will exchange data. Both computers should have the sam...

  • Page 79

    72 bios and driver setting ©vecow ecs-9200/9100 gtx1050 user manual hyper-threading enabled for windows xp and linux (os optimized for hyper-threading technology) and disabled for other os (os not optimized for hyper-threading technology). When disabled, only one thread per core is enabled. Active p...

  • Page 80

    73 bios and driver setting 4.3.9 intel txt information display intel txt information. Figure 4 3-9: intel txt information 4.3.10 sata configuration figure 4 3-10: sata devices settings cpu c state enable or disable cpu c states. Enhanced c-states enable/disable c1e. When enabled, cpu will switch to ...

  • Page 81

    74 bios and driver setting ©vecow ecs-9200/9100 gtx1050 user manual sata controller(s) enable or disable sata device. Sata mode selection determines how sata controller(s) operate. Software feature mask configuration raid orom/rst driver will refer to the swfm configuration to enable or disable the ...

  • Page 82

    75 bios and driver setting 4.3.12 csm configuration csm support enable/disable csm support gatea20 active upon request - ga20 can be disabled using bios services. Always - do not allow ga20 to be disabled; this option is useful when any rt code is executed above 1mb. Option rom messages set display ...

  • Page 83

    76 bios and driver setting ©vecow ecs-9200/9100 gtx1050 user manual 4.3.13 usb configuration legacy usb support enables legacy usb support. Auto option disables legacy support if no usb devices are connected. Disable option will keep usb devices available only for efi applications. Xhci hand-off thi...

  • Page 84: 4.4   Chipset

    77 bios and driver setting vt-d vt-d capability. Gmm device (b0:d8:f0) enable/disable sa gmm device. Above 4gb mmio bios assignment enable/disable above 4gb memorymappedio bios assignment. This is disabled automatically when aperture size is set to 2048mb. 4.4.1 system agent (sa) configuration figur...

  • Page 85

    78 bios and driver setting ©vecow ecs-9200/9100 gtx1050 user manual 4.4.2 graphics configuration of system agent (sa) gtt size select the gtt size. Aperture size select the aperture size. Note: above 4gb mmio bios assignment is automatically enabled when selecting 2048mb aperture. To use this featur...

  • Page 86

    79 bios and driver setting 4.4.4 memory information of system agent (sa) displays memory information. Figure 4-4-4: memory information 4.4.5 pch-io configuration figure 4-4-5: pch-io settings pch lan controller enable or disable onboard nic. Wake on lan enable or disable integrated lan to wake the s...

  • Page 87

    80 bios and driver setting ©vecow ecs-9200/9100 gtx1050 user manual 4.4.6 pci express configuration of pch-io figure 4-4-6: pch-io settings dmi link aspm control enable/disable the control of active state power management on sa side of the dmi link. Native pcie enable pci express native support enab...

  • Page 88

    81 bios and driver setting 4.4.8 sb porting configuration of pch-io sata raid rom legacy rom: legacy option rom uefi driver: uefi raid driver both: run the legacy option rom and uefi driver. Figure 4-4-8: raid rom settings 4.4.9 gpio manager configuration vga enable enable: vga display output enable...

  • Page 89: 4.5   Security

    82 bios and driver setting ©vecow ecs-9200/9100 gtx1050 user manual set user password set hdd user password. *** advisable to power cycle system after setting hard disk passwords *** discard or save changes option in setup does not have any impact on hdd when password is set or removed. If the 'set ...

  • Page 90: 4.6   Boot

    83 bios and driver setting 4.6 boot figure 4-6: bios boot menu setup prompt timeout number of seconds to wait for setup activation key. 65535(0xffff) means indefinite waiting. Bootup numlock state select the keyboard numlock state. Quiet boot enables or disables quiet boot option. Boot option sets t...

  • Page 91: 4.7   Save & Exit

    84 bios and driver setting ©vecow ecs-9200/9100 gtx1050 user manual 4.7 save & exit figure 4-7: bios save and exit menu save changes and exit exit system setup after saving the changes. Discard changes and exit exit system setup without saving any changes. Save changes and reset reset the system aft...

  • Page 92: A.1   Function Description

    85 appendix a a appendix a : isolated dio guide a.1 function description ecs-9200 gtx1050 offers two 16-bit dio (isolated / non-isolated) 20-pin terminal block connector, a watchdog timer, and a 4-port poe. Isolated dio pins are fix by hardware design that cannot change in / out direction in runtime...

  • Page 93: Poe

    86 ©vecow ecs-9200/9100 gtx1050 user manual appendix a a.2 isolated dio signal circuit di reference circuit: sink mode (npn) v+ v- power supply 6-48v dc di_com (pin 9) di (pin1-8) dio connector source mode (pnp) v+ v- power supply 6-48v dc di_com (pin 9) di (pin1-8) dio connector do reference circui...

  • Page 94

    87 appendix a a.3 software package contain distribution folder include x32 and x64 versions, use batch file for installation. There are included as fallowed: win7_32.Bat: installation for 32-bit driver win7_64.Bat: windows update package which driver required (need to restart), and installation for ...

  • Page 95: A.4   Sample

    88 ©vecow ecs-9200/9100 gtx1050 user manual appendix b sample ecs9k2.Exe, shown as below: a.4 sample sample folder includes x32 and x64 versions, shown as below:.

  • Page 96

    89 appendix b dio1 / dio2 group: isolate check button: dio type of dio configuration, isolated / non-isolated, defined in ecs-9000 series user manual. Read button: set dio configuration to get di / dio input state. Do type check button: user setting, do type of dio configuration to setup 8 pins - so...

  • Page 97

    90 ©vecow ecs-9200/9100 gtx1050 user manual appendix b wdt setup text: user setting, wdt value, unit: second. Use for write button activate. Wdt counting text (read only): wdt counting by program timer after set wdt. Shown after write button action. Wdt setup day format texts (user setting): user se...

  • Page 98: B.1   Driver Api Guide

    91 appendix b b appendix b : software functions b.1 driver api guide in runtime folder, on ecs9k2.H: _dll_import_ definition is used on loadlibrary api for ecs9k2.Dll. Ecs9k_exports definition is used on ecs9k2.Dll building. Otherwise, that is used to compile with ecs9k2.Lib. Bool initial(byte isola...

  • Page 99

    92 ©vecow ecs-9200/9100 gtx1050 user manual appendix b bool setdio1config(byte *isolate_type, byte *di_npn, byte *do_npn, word *mask) bool setdio2config(byte *isolate_type, byte *di_npn, byte *do_npn, word *mask) set dio configuration isolate_type: dio type 1: isolated dio; 0: non-isolated dio di_np...

  • Page 100

    93 appendix b bool getdio1(word *di) bool getdio2(word *di) get non-isolated dio input (dio input) di ([15:0]): input state, pin setting by hexadecimal bitmask 1: high; 0: low return: true (1): success; false (0): fail (initial error, or call by pointer error, or hardware problem) bool setdio1(word ...

  • Page 101

    94 ©vecow ecs-9200/9100 gtx1050 user manual appendix c 1: enable; 0: disable return: true (1): success; false (0): fail (initial error, or call by pointer error, or hardware problem) bool setpoeconfig(byte auto, byte mask) set poe configuration auto ([3:0]): auto mode, pin setting by hexadecimal bit...

  • Page 102: C.1   Sata Mode For Raid

    95 appendix c c appendix c : raid installation guide c.1 sata mode for raid please select sata device to raid mode on bios menu. Advanced → sata configuration → sata mode selection c.2 os installation ecs-9200/9100 gtx1050 is featured with six sata, include two internal sata, three msata and one cfa...

  • Page 103: C.6   Create Raid Volume

    96 ©vecow ecs-9200/9100 gtx1050 user manual appendix c c.4 install “intel rapid storage technology” software you can get the software on ecs-9200/9100 gtx1050 driver cd. Also, you can find latest information and software directly from intel website. Http://www.Intel.Com/p/en_us/support/highlights/ch...

  • Page 104: C.8   Raid Hdd Fail

    97 appendix c then add “logical device” for windows access. C.7 disk management : partition the disk after raid 1 volume created, you can see the figure of sata device allocation. To start disk management tool, select "initialize disk." you will find “volume_0000” in sata device at bios menu. C.8 ra...

  • Page 105: C.10   New Hdd Recovery

    98 ©vecow ecs-9200/9100 gtx1050 user manual appendix c c.10 new hdd recovery there is a warning will pop-up to ask you if the disk is not a member of original raid volume. If you press “rebuild”, it will replace the broken sata hdd to the last one sata hdd of raid volume. C.9 original hdd recovery.

  • Page 106

    99 appendix d d appendix d : power consumption testing board ecs-9200 gtx1050 ram 8gb x 2 usb-1 usb keyboard logitech k120 usb-2 usb mouse microsoft 1113 usb-3 usb flash transecnd 3.0 8gb usb-4 usb flash transecnd 3.0 8gb cfast innodisk cfast 3me3 64gb sata 0 memxpro m3a 256gb sata 1 toshiba ssd thn...

  • Page 107

    100 ©vecow ecs-9200/9100 gtx1050 user manual appendix d d.1 intel® core™ i7-6700 (8m cache, up to 4.00 ghz) cpu power input sleep mode idle status : cpu usage less 3% max current max consumption max current max consumption core™ i7- 6700 15v 0.324a 04.86w 1.810a 27.15w core™ i7- 6700 24v 0.276a 06.6...

  • Page 108: Storage List

    101 appendix e e appendix e : supported memory & storage list testing board ecs-9200 gtx1050 memory test version: 5.1 burnintest v8.1 e.1 supported memory list channel memory test burn in flash bios remove battery *2 pass pass pass pass *1(socket 1) pass pass n/a pass *1(socket 2) pass pass n/a pass...

  • Page 109: E.3   Non-Ecc

    102 ©vecow ecs-9200/9100 gtx1050 user manual appendix e brand info note & s test temp. (celsius) kingston 16gb 2rx8 2gx64-bit pc4-2133 kvr21s15d8/16 bkmm1641607 25ºc bkmm1661618 25ºc memxpro 4gb ddr4-2133-15 wild temp. D4s4ghiofei 01611170040001 25ºc 01611170040002 25ºc memxpro 8gb ddr4-2133-15 wi...

  • Page 110

    103 appendix e type brand model capacity msata intel intel-310 ssdmaemc080g2 80gb silicon power sp128gimsa301sw0 128gb sata ssd transcend ssd370 ts64gssd370 64gb memxpro ssd m3a mi3ma1212802wn 128gb ssd m3a mi3ma1225604wn 256gb ssd m3a mi3ma1251208wn 512gb innodisk 3mr3-p drs25-64gd70bcaqc 64gb sili...

  • Page 111

    104 ©vecow ecs-9200/9100 gtx1050 user manual appendix f ** if more help is needed, please contact vecow technical support ** f appendix f : graphics performance test temperature (based on 95% humidity) 30ºc 35ºc 40ºc 45ºc 50ºc 55ºc 60ºc 3dmark 11 (v1.5.5.0) resolution 1920 x 1080 score x3074 x3056 x...

  • Page 112

    For further support information, please visit www.Vecow.Com this document is released for reference purpose only. All product offerings and specifications are subject to change without prior notice. No part of this publication may be reproduced in any form or by any means, electric, photocopying, or...