1. DL manuals
  2. Vecow
  3. Desktop
  4. ECS-9600-505M-GTX1050
  5. User Manual

Vecow ECS-9600-505M-GTX1050 User Manual

Manual is about: Quad Core Intel Xeon / Core i7 Processor Embedded System with Intel CM236 & NVIDIA GEFORCE GTX1050 Ti / GTX1050 Graphics, High Performance, Independent Graphics, all-in-one integrated

Summary of ECS-9600-505M-GTX1050

  • Page 1

    User manual user manual 1.1.0 edition 20171103 ecs-9700/9600 gtx1050 quad core intel ® xeon ® / core ™ i7 processor embedded system with intel ® cm236 & nvidia geforce ® gtx1050 ti/gtx1050 graphics, high performance, independent graphics, all-in-one integrated.

  • Page 2: Record of Revision

    Ii version date page description remark 1.0 07/25/2017 all official release 1.1 11/03/2017 49-62 update record of revision.

  • Page 3: Fcc

    Iii this manual is released by vecow co., ltd. For reference purpose only. All product offerings and specifications are subject to change without prior notice. It does not represent commitment of vecow co., ltd. Vecow shall not be liable for direct, indirect, special, incidental, or consequential da...

  • Page 4: Order Information

    Iv part number description ecs-9740-505m- gtx1050t ecs-9700, intel ® xeon ® e3-1505m v5, nvidia geforce ® gtx1050 ti, 6 gige lan w/4 poe + , 2 ssd, 6 usb 3.0, 4 com, 4 sim, 32 isolated dio (ecc supported) ecs-9740-505m- gtx1050 ecs-9700, intel ® xeon ® e3-1505m v5, nvidia geforce ® gtx1050, 6 gige l...

  • Page 5: Order Accessories

    V part number description ddr4 16g certified ddr4 16gb 2133mhz ram ddr4 8g certified ddr4 8gb 2133mhz ram ddr4 4g certified ddr4 4gb 2133mhz ram pwa-280wb-wt 280w, 24v, 85v ac to 264v ac power adapter with 3-pin terminal block (7.62mm pitch), wide temperature -30°c to +70°c pwa-160wb-wt 160w, 24v, 8...

  • Page 6: Table of Contents

    Vi table of contents chapter 1 general introduction 1 1.1 overview 1 1.2 features 2 1.3 product specification 2 1.3.1 specifications of ecs-9740 gtx1050 2 1.3.2 specifications of ecs-9600 gtx1050 4 1.4 supported cpu list 7 1.5 mechanical dimension 8 1.5.1 dimensions of ecs-9740 gtx1050 8 1.5.2 dimen...

  • Page 7: Chapter   4

    Vii chapter 4 bios setup 63 4.1 entering bios setup 63 4.2 main 64 4.3 advanced 64 4.4 chipset 74 4.5 security 79 4.6 boot 80 4.7 save & exit 81 appendix a : isolated dio guide 82 appendix b : software functions 89 appendix c : raid installation guide 93 appendix d : power consumption 97 appendix e ...

  • Page 8: General Introduction

    1 general introduction 1 general introduction vecow ecs-9700/9600 gtx1050 series is an all-in-one integrated, high- performance embedded system. Powered by workstation-grade intel ® xeon ® / core™ i7 processor (skylake-h) running with dual-channel ddr4 2133mhz ecc memory and independent nvidia gefor...

  • Page 9: 1.2   Features

    2 general introduction ©vecow ecs-9700/ 9600 gtx1050 user manual 1.2 features • quad core intel ® xeon ® /core™ i7 processor (skylake-h) with cm236 chipset supports up to 6 independent displays • nvidia geforce ® gtx 10 series graphics engine supports nvidia pascal™ gpu architecture, up to 8k resolu...

  • Page 10

    3 general introduction expansion mini pcie 4 mini pcie socket : • 3 full-size for pcie/usb/external sim card/msata • 1 full-size for pcie/internal sim card/msata sumit a, b 2 sumit slot (optional) graphics graphics processor • intel ® hd graphics p530/530 • nvidia ® geforce ® gtx1050 ti/gtx1050 inte...

  • Page 11

    4 general introduction ©vecow ecs-9700/ 9600 gtx1050 user manual others tpm optional infineon slb9665 supports tpm 2.0, lpc interface watchdog timer reset : 1 to 255 sec./min. Per step smart management wake on lan, pxe supported hw monitor monitoring temperature, voltages. Auto throttling control wh...

  • Page 12

    5 general introduction i/o interface serial 4 com rs-232/422/485 w/auto flow control (esd 8kv) usb • 6 usb 3.0 (external) • 1 usb 2.0 (internal) isolated dio 16 isolated dio (8 di, 8 do) led power, hdd, wireless sim card 4 sim card socket (3 external, 1 internal) expansion mini pcie 4 mini pcie sock...

  • Page 13

    6 general introduction ©vecow ecs-9700/ 9600 gtx1050 user manual power input voltage 10v to 36v, dc-in power interface 3-pin terminal block : v+, v-, frame ground ignition control 16 mode (internal) remote switch 3-pin terminal block : on, off, ign surge protection up to 80v/1ms transient power othe...

  • Page 14: 1.4   Supported Cpu List

    7 general introduction 1.4 supported cpu list processor no. Tdp cache max. Frequency embedded xeon ® e3-1575m v5 45w 8m up to 3.00 ghz xeon ® e3-1545m v5 45w 8m up to 2.90 ghz xeon ® e3-1535m v5 45w 8m up to 2.80 ghz xeon ® e3-1515m v5 45w 8m up to 2.80 ghz xeon ® e3-1505m v5 45w 8m up to 2.80 ghz y...

  • Page 15: 1.5   Mechanical Dimension

    8 general introduction ©vecow ecs-9700/ 9600 gtx1050 user manual 1.5 mechanical dimension 1.5.1 dimensions of ecs-9740 gtx1050 260.0 (10.24”) 282.0 (11.10”) 297.0 (11.69”) 155.0 (6.10”) 215.0 (8.46”) 79.1 (3.1 1”) 99.1 (3.90”) unit: mm (inch) 1.5.2 dimensions of ecs-9600 gtx1050 260.0 (10.24”) 282.0...

  • Page 16: 2.1   Packing List

    9 getting to know your ecs-9700/ 9600 gtx1050 2 getting to know your ecs-9700/9600 gtx1050 2.1 packing list item description qty 1 ecs-9740/9600 gtx1050 embedded system (according to the configuration you order, the ecs-9740/9600 gtx1050 series may contain ssd/hdd and ddr4 so-dimm. Please verify the...

  • Page 17

    10 getting to know your ecs-9700/ 9600 gtx1050 ©vecow ecs-9700/ 9600 gtx1050 user manual 2.2 front panel i/o & functions in vecow ecs-9700/9600 gtx1050 series family, all i/o connectors are located on the front panel and the rear panel. Most of the general connections to computer device, such as usb...

  • Page 18

    11 getting to know your ecs-9700/ 9600 gtx1050 pin no. Description pin no. Description s1 gnd pc6 nc s2 sata_txp5 pc7 gnd s3 sata_txn5 pc8 cfast_led s4 gnd pc9 nc s5 sata_rxn5 pc10 nc s6 sata_rxp5 pc11 nc s7 gnd pc12 nc 2.2.3 cfast card there is a cfast socket on the front panel supporting type-i/ii...

  • Page 19

    12 getting to know your ecs-9700/ 9600 gtx1050 ©vecow ecs-9700/ 9600 gtx1050 user manual pin no. Description pin no. Description pc1 gnd pc13 +3.3v pc2 gnd pc14 +3.3v pc3 nc pc15 gnd pc4 nc pc16 gnd pc5 nc pc17 nc 2.2.4 pwr and hdd led indicator hdd led/yellow : a hard disk/ cfast led. If the led is...

  • Page 20

    13 getting to know your ecs-9700/ 9600 gtx1050 the dvi-d connector on the front panel supports dvi display. This connector can output dvi signal. The dvi output mode supports up to 1920 x 1200 resolution and the dvi is automatically selected according to the display device connected. You will need a...

  • Page 21

    14 getting to know your ecs-9700/ 9600 gtx1050 ©vecow ecs-9700/ 9600 gtx1050 user manual 2.2.8 3 of 4 independent displays you could have 3 independent displays as your wish from these 4 display ports. Also, you could have two 4k resolution displays, the 2 displayport, from these 4 ports. Rst dp lan...

  • Page 22

    15 getting to know your ecs-9700/ 9600 gtx1050 2.2.11 audio jack there are 2 audio connectors, mic-in and line-out, in the front side of ecs-9700 /9600 gtx1050. Onboard realtek alc892 audio codec supports 5.1 channel hd audio and fully complies with intel ® high definition audio (azalia) specificati...

  • Page 23

    16 getting to know your ecs-9700/ 9600 gtx1050 ©vecow ecs-9700/ 9600 gtx1050 user manual 2.2.12 wlan led, mini pcie, sim card comparison rst dp lan 1 lan 2 dvi-d vga cfast sim 1 sim 3 sim 2 1 2 3 4 wlan mini pcie sim led mini pcie 1 / msata (cn12) sim 1 (cn13) 1 mini pcie 2 / msata (cn8) sim 2 (cn9)...

  • Page 24

    17 getting to know your ecs-9700/ 9600 gtx1050 hdd tray mb connector mb power connector hdd 1 sata1 power conn 1 hdd 2 sata2 power conn 1 sata3 power conn 2 sata4 (remark: by mb bom optional, default no signal link) power conn 2 2.2.13 ssd/hdd tray there are 2 front-access 2.5’’ ssd/hdd trays in the...

  • Page 25

    18 getting to know your ecs-9700/ 9600 gtx1050 ©vecow ecs-9700/ 9600 gtx1050 user manual 2.3 rear panel i/o & functions 2.3.1 power terminal block it is a 5-pin power-on or power-off switch through phoenix contact terminal block. You could turn on or off the system power by using this contact. This ...

  • Page 26

    19 getting to know your ecs-9700/ 9600 gtx1050 serial port pin no. Rs-232 rs-422 (5-wire) rs-422 (9-wire) rs-485 (3-wire) 1 to 4 1 dcd txd- txd- data- 2 rxd txd+ txd+ data+ 3 txd rxd+ rxd+ ----------- 4 dtr rxd- rxd- ----------- 5 gnd gnd gnd gnd 6 dsr ----------- rts- ----------- 7 rts ----------- ...

  • Page 27

    20 getting to know your ecs-9700/ 9600 gtx1050 ©vecow ecs-9700/ 9600 gtx1050 user manual com3 & com 4 mb connector table: com port mb connector com port mb connector com 3 cn27 com 4 cn28 cn pin no. Signal name cn27(com3) cn28(com4) 1 chassis gnd 2 gnd 3 ri 4 dtr 5 cts 6 txd 7 rts 8 rxd 9 dsr 10 dcd...

  • Page 28

    21 getting to know your ecs-9700/ 9600 gtx1050 2.3.5 poe (power over ethernet) ports there are quad 8-pin poe rj-45 jacks supporting 10/100/1000 mbps ethernet connections in the front side. Powered by intel i210 ethernet engine. When both lan 1 and lan 2 work in normal status, iamt 11.0 function is ...

  • Page 29

    22 getting to know your ecs-9700/ 9600 gtx1050 ©vecow ecs-9700/ 9600 gtx1050 user manual each lan port is supported by standard rj-45 connector with led indicators to present active/link/speed status of the connection & poe status led. The led indicator on the right bottom corner lightens in solid g...

  • Page 31

    24 getting to know your ecs-9700/ 9600 gtx1050 ©vecow ecs-9700/ 9600 gtx1050 user manual dio pin no. Definition function dio2 1 input 8 sio_gpi37 2 input 9 sio_gpi50 3 input 10 sio_gpi51 4 input 11 sio_gpi52 5 input 12 sio_gpi56 6 input 13 sio_gpi57 7 input 14 sio_gpi64 8 input 15 sio_gpi65 9 di2_co...

  • Page 33

    26 getting to know your ecs-9700/ 9600 gtx1050 ©vecow ecs-9700/ 9600 gtx1050 user manual 2.4 main board expansion connectors 2.4.1 inside view of ecs-9700/9600 gtx1050 main board with connector location fn1 sata1 sata2 cn27 cn5 cn28 jp2 j9 j8 sata3 sata4 cn1 sw2 jp7 jp10 jp8 cn2 j10 sw5 jp11 sw7 sw1...

  • Page 34

    27 getting to know your ecs-9700/ 9600 gtx1050 2.4.2 ups power connector for ups module optional, we use 4.2mm 2x2p power connector this system has a ups power input connector for optional part ups module. Pin no. Definition pin no. Definition 1 ground 2 ground 3 +vdc_in (10~36v, max.8a) 4 +vdc_in (...

  • Page 35

    28 getting to know your ecs-9700/ 9600 gtx1050 ©vecow ecs-9700/ 9600 gtx1050 user manual group pin no. Description hdd led 1 hdd_led_p 3 hdd_led_n reset button 5 fp_rst_btn_n 7 ground power led 2 pwr_led_p 4 pwr_led_n power button 6 fp_pwr_btn_in 8 ground 2.4.4 ddr4 slot there are 2 ddr4 channel onb...

  • Page 36

    29 getting to know your ecs-9700/ 9600 gtx1050 2.4.5 bios socket if the bios needs to be changed, please contact the vecow rma service team. Cn1 2.4.6 sata connector standard 7 pin sata connector there are 4 onboard high performance serial ata iii. It supports higher storage capacity with less cabli...

  • Page 37

    30 getting to know your ecs-9700/ 9600 gtx1050 ©vecow ecs-9700/ 9600 gtx1050 user manual 2.4.7 sata power header standard, all form factor 1x4p power header there are 2 hdd power headers on board and each power header supports two 2.5” sata hdd. Pin no. Description pin no. Description 1 +v5 (max. 4a...

  • Page 38

    31 getting to know your ecs-9700/ 9600 gtx1050 2.4.9 sumit a, sumit b (optional) this system has standard sumit a and sumit b for sumit type add on cards. Sumitb sumita pin no. Definition pin no. Definition 1 usb +vcc (+v5/max. 0.5a) 2 data- 3 data+ 4 ground cn20

  • Page 39

    32 getting to know your ecs-9700/ 9600 gtx1050 ©vecow ecs-9700/ 9600 gtx1050 user manual pin no. Function pin no. Function 1 +5v_aux 2 +12v 3 +3.3v 4 smb_data 5 +3.3v 6 xmb_clk 7 reserved 8 reserved 9 reserved 10 spi_miso 11 usb_oc# 12 spi_mosi 13 reserved 14 spi_clk 15 +5v 16 spi_cs10 17 usb_3+ 18 ...

  • Page 40

    33 getting to know your ecs-9700/ 9600 gtx1050 pin no. Function pin no. Function 1 gnd 2 gnd 3 b_pet_p0 4 b_per_p0 5 b_pet_n0 6 b_per_n0 7 gnd 8 gnd 9 c_clkp 10 b_clkp 11 c_clkn 12 b_clkn 13 cprsnt#/c_pe_clkreq# 14 gnd 15 c_pet_p0 16 c_per_p0 17 c_pet_n0 18 c_per_n0 19 gnd 20 gnd 21 c_pet_p1 22 c_pe...

  • Page 41

    34 getting to know your ecs-9700/ 9600 gtx1050 ©vecow ecs-9700/ 9600 gtx1050 user manual 2.4.10 mini pcie/ msata slot cn6 cn10 cn12 cn8 sw2 mini pcie and msata share the same form factor and have similar electrical pinout assignments on their connectors. There’s no clear mechanism to distinguish if ...

  • Page 42

    35 getting to know your ecs-9700/ 9600 gtx1050 pin no. Function pin no. Function 51 reserved 52 +3.3vaux 49 reserved 50 gnd 47 reserved 48 +1.5v 45 reserved 46 reserved 43 gnd 44 reserved 41 +3.3vaux 42 reserved 39 +3.3vaux 40 gnd 37 gnd 38 usb_d+ 35 gnd 36 usb_d- 33 petp0 34 gnd 31 petn0 32 smb_dat...

  • Page 43

    36 getting to know your ecs-9700/ 9600 gtx1050 ©vecow ecs-9700/ 9600 gtx1050 user manual 2.4.11 rtc battery ecs-9700/9600 gtx1050 real-time clock is powered by a lithium battery. It is equipped with panasonic br2032 190mah lithium battery. It is recommended that you do not have to get the lithium ba...

  • Page 44

    37 getting to know your ecs-9700/ 9600 gtx1050 pin no. Function pin no. Function 1 serirq 7 lframe# 2 +3.3v 8 lad0 3 la3 9 n/c 4 reset# 10 ground 5 lad1 11 clock 6 lad2 12 ground pin out: 2.4.13 lpc port 80 header ecs-9700/9600 gtx1050 provides a lpc port 80 header for debug card. Cn3 2.4.14 lan iee...

  • Page 45

    38 getting to know your ecs-9700/ 9600 gtx1050 ©vecow ecs-9700/ 9600 gtx1050 user manual j9 j8 j7 j6 jp3 pin no. Function pin no. Function 1 spd0 2 spd1 3 spd2 4 spd3 5 ground 6 ground pin out:.

  • Page 46

    39 getting to know your ecs-9700/ 9600 gtx1050 2.4.15 com port header ecs-9700/9600 gtx1050 provides 4 com port headers for internal com port cables. Cn27 cn28 pin no. Description port 1 ground_frame com3 2 ground com3 3 ri com3 4 dtr com3 5 cts com3 6 txd com3 7 rts com3 8 rxd com3 9 dsr com3 10 dc...

  • Page 47

    40 getting to know your ecs-9700/ 9600 gtx1050 ©vecow ecs-9700/ 9600 gtx1050 user manual 2.5 main board jumper & deep switch settings 2.5.1 top view of ecs-9700/9600 gtx1050 with jumper and deep switch the figure below is the top view of ecs-9700/9600 gtx1050 board, and it shows the location of the ...

  • Page 48

    41 getting to know your ecs-9700/ 9600 gtx1050 you may configure your card to match the needs of your application by dip switch as shown below (the deep switch on and off) on 1 2 1 : off 2 : off on 1 2 1 : on 2 : off on 1 2 1 : on 2 : on 2.5.2 usb power jumper jumper setting function usb port jp3 1:...

  • Page 49

    42 getting to know your ecs-9700/ 9600 gtx1050 ©vecow ecs-9700/ 9600 gtx1050 user manual 2.5.3 com port ri pin select pin header pin no. Description com1 jp5 1-2 +5v (1a max.) 3-4 +12v (0.5a max.) 5-6 ri (default) pin header pin no. Description com2 jp6 1-2 +5v (1a max.) 3-4 +12v (0.5a max.) 5-6 ri ...

  • Page 50

    43 getting to know your ecs-9700/ 9600 gtx1050 2.5.4 com port rs-422/rs-485 receiver terminator sw3 sw4 com / dip switch on / off com rs-422/485 receiver terminator com1 / sw3-1 on *enable off disable com / dip switch on / off com rs-422/485 receiver terminator com2 / sw3-2 on *enable off disable co...

  • Page 51

    44 getting to know your ecs-9700/ 9600 gtx1050 ©vecow ecs-9700/ 9600 gtx1050 user manual 2.5.5 poe power on select jumper setting function jp9 1:2 poe power on at standby power ready jp9 2:3 poe power on after system power on (default) jp9 2.5.6 clear cmos/me switch function dip switch description s...

  • Page 52: 2.6   Ignition Control

    45 getting to know your ecs-9700/ 9600 gtx1050 2.6 ignition control 2.6.1 adjust ignition control modes ecs-9700/9600 gtx1050 series provides ignition power control feature for in- vehicle applications. The built-in mcu monitors the ignition signal and turns on/ off the system according to pre-defin...

  • Page 53

    46 getting to know your ecs-9700/ 9600 gtx1050 ©vecow ecs-9700/ 9600 gtx1050 user manual the modes are listed in the following table: item power on delay power off delay switch position 0 atx mode 1 no delay no delay 2 no delay 5 seconds 3 no delay 10 seconds 4 no delay 20 seconds 5 5 seconds 30 sec...

  • Page 54

    47 getting to know your ecs-9700/ 9600 gtx1050 2.6.2 ignition control wiring to activate ignition control, you need to provide ign signal via the 3-pin pluggable terminal block located in the back panel. Please find below the general wiring configuration. For testing purpose, you can refer to the pi...

  • Page 55

    48 getting to know your ecs-9700/ 9600 gtx1050 ©vecow ecs-9700/ 9600 gtx1050 user manual 2.6.3 smart battery protection the system with “ignition control” can perform smart battery protection, namely low battery detection. When the system is running on a battery and its voltage drops below the thres...

  • Page 56: System Setup

    49 hardware installation system setup 3.1 how to open your ecs-9700/9600 gtx1050 3 step 1 remove hole plugs. Step 2 remove two f#6-32 screws (circled in red) and two f-m3 screws (circled in yellow) on the bottom side..

  • Page 57

    50 hardware installation ©vecow ecs-9700/ 9600 gtx1050 user manual step 3 finish step1 and 2. Step 4 remove one khs#6-32x6 screws..

  • Page 58

    51 hardware installation step 6 finish. Step 5 open the module..

  • Page 59

    52 hardware installation ©vecow ecs-9700/ 9600 gtx1050 user manual 3.2 installing ddr4 so-dimm modules step 1 ddr4 ram module into so-dimm slot. Step 2 make sure the ram module is locked by the memory slot..

  • Page 60

    53 hardware installation 3.3 installing mini pcie card step 1 install mini pcie card into the mini pcie socket. Step 2 fasten one m2.5 screw..

  • Page 61: 3.4   Installing Cfast Card

    54 hardware installation ©vecow ecs-9700/ 9600 gtx1050 user manual 3.4 installing cfast card step 1 remove 2 pcs f-m3x4 screws on cfast & sim card. Step 2 before inserting cfast & sim card, make sure ecs-9700/9600 gtx1050 power is not plugged. Step 3 insert cfast card and push to lock. Step 4 insert...

  • Page 62: 3.5   Installing Sim Card

    55 hardware installation 3.5 installing sim card step 1 remove 2 pcs f-m3x4 screws on cfast & sim card. Step 2 before inserting cfast & sim card, make sure ecs-9700/9600 gtx1050 power is not plugged. Step 3 insert cfast card and push to lock. Step 4 insert sim card and push to lock..

  • Page 63: 3.6   Installing Ssd/ Hdd

    56 hardware installation ©vecow ecs-9700/ 9600 gtx1050 user manual 3.6 installing ssd/ hdd step 1 trigger and open ssd/hdd tray. Step 2 insert 2.5” ssd/hdd in the tray and fasten two f-m3x4 screws..

  • Page 64

    57 hardware installation step 3 finish. Step 4 installing ssd/hdd..

  • Page 65

    58 hardware installation ©vecow ecs-9700/ 9600 gtx1050 user manual 3.7 mounting your ecs-9700/9600 gtx1050 step 1 ensure the screw holes on the right and left side of the upper case match the ones on ecs-9700/9600 gtx1050 wall mount bracket. 3.7.1 wall mount bracket step 2 fasten 4pcs khs#6-32 screw...

  • Page 66

    59 hardware installation 3.7.2 vesa mount step 1 ecs-9700/9600 gtx1050 and vesa mount. Step 2 take ecs-9700/9600 gtx1050 and vesa mount with fasten 4pcs khs#6-32 screws..

  • Page 67

    60 hardware installation ©vecow ecs-9700/ 9600 gtx1050 user manual step 3 fasten four khs#6-32 screws and then finish. Step 4 finish. Step 5 vesa size have 75x75mm(red) and 100x100mm(yellow)..

  • Page 68

    61 hardware installation 3.7.3 din rail kit step 1 ecs-9700/9600 gtx1050 and din rail kit. Step 2 take ecs-9700/9600 gtx1050 and din rail kit and fasten four khs#6-32 screws in the four marked corners..

  • Page 69

    62 hardware installation ©vecow ecs-9700/ 9600 gtx1050 user manual step 3 fasten four khs#6-32 screws and then finish. Step 4 finish. Step 5 ecs-9700/9600 gtx1050 with din rail..

  • Page 70: Bios Setup

    63 bios and driver setting 4 bios setup 4.1 entering bios setup bios provides an interface for users to check and change system configuration. The bios setup program is accessed by pressing the key when post display output is shown. Figure 4-1: entering setup screen.

  • Page 71: 4.2   Main

    64 bios and driver setting ©vecow ecs-9700/ 9600 gtx1050 user manual 4.2 main the main menu displays bios version and system information. There are two options on main menu. System date set the date. Use to switch between date elements. System time set the time. Use to switch between time elements. ...

  • Page 72

    65 bios and driver setting 4.3.1 trusted computing control the tpm device status and display related information if tpm chip is present. Figure 4 3-1: trusted computing 4.3.2 acpi settings enable hibernation enables or disables system's ability to hibernate (os/s4 sleep state). This option may not b...

  • Page 73

    66 bios and driver setting ©vecow ecs-9700/ 9600 gtx1050 user manual 4.3.4 pch-fw configuration me unconfig on rtc clear state disabling this option will cause me not to unconfigure on rtc clear. Me state set me to soft temporarily disabled. Figure 4 3-4: pch-fw settings 4.3.5 smart settings smart s...

  • Page 74

    67 bios and driver setting 4.3.6 it8786 super io configuration figure 4-3-6-1: super io settings set the direction of the gpio pins creates bios options for end user to change internal gpio pin direction. Figure 4 3-6-3: gpio pin input/output settings of sio it8786 figure 4-3-6-2: serial port settin...

  • Page 75

    68 bios and driver setting ©vecow ecs-9700/ 9600 gtx1050 user manual 4.3.8 serial port console redirection console redirection console redirection enable or disable. Console redirection settings these settings specify how the host computer and the remote computer (which the user is using) will excha...

  • Page 76

    69 bios and driver setting hyper-threading enabled for windows xp and linux (os optimized for hyper-threading technology) and disabled for other os (os not optimized for hyper-threading technology). When disabled only one thread per core is enabled. Active processor cores number of cores to enable i...

  • Page 77

    70 bios and driver setting ©vecow ecs-9700/ 9600 gtx1050 user manual 4.3.10 intel txt information display intel txt information. Figure 4 3-10: intel txt information 4.3.11 sata configuration figure 4 3-11: sata devices settings cpu c state enable or disable cpu c states. Enhanced c-states enable/di...

  • Page 78

    71 bios and driver setting sata controller(s) enable or disable sata device. Sata mode selection determines how sata controller(s) operate. Software feature mask configuration raid orom/rst driver will refer to the swfm configuration to enable or disable the storage features. Aggressive lpm support ...

  • Page 79

    72 bios and driver setting ©vecow ecs-9700/ 9600 gtx1050 user manual 4.3.13 csm configuration csm support enable/disable csm support gatea20 active upon request - ga20 can be disabled using bios services. Always - do not allow ga20 to be disabled; this option is useful when any rt code is executed a...

  • Page 80

    73 bios and driver setting 4.3.14 usb configuration legacy usb support enables legacy usb support. Auto option disables legacy support if no usb devices are connected. Disable option will keep usb devices available only for efi applications. Xhci hand-off this is a workaround for os-es without xhci ...

  • Page 81: 4.4   Chipset

    74 bios and driver setting ©vecow ecs-9700/ 9600 gtx1050 user manual vt-d vt-d capability. Gmm device (b0:d8:f0) enable/disable sa gmm device. Above 4gb mmio bios assignment enable/disable above 4gb memorymappedio bios assignment. This is disabled automatically when aperture size is set to 2048mb. 4...

  • Page 82

    75 bios and driver setting 4.4.2 graphics configuration of system agent (sa) graphics turbo imon current graphics turbo imon current values supported (14-31). Skip scaning of external gfx card if enable, it will not scan for external gfx card on peg and pch pcie ports. Primary display select which o...

  • Page 83

    76 bios and driver setting ©vecow ecs-9700/ 9600 gtx1050 user manual 4.4.3 peg port configuration (sa) peg port options for pcie device. Figure 4-4-3: peg port configuration 4.4.4 memory information of system agent (sa) displays memory information. Figure 4-4-4: memory information 4.4.5 pch-io confi...

  • Page 84

    77 bios and driver setting pch lan controller enable or disable onboard nic. Wake on lan enable or disable integrated lan to wake the system. (the wake on lan cannot be disabled if me is on at sx state.) serial irq mode configure serial irq mode. State after g3 specify what state to go to when power...

  • Page 85

    78 bios and driver setting ©vecow ecs-9700/ 9600 gtx1050 user manual 4.4.7 bios security configuration of pch-io bios lock enable/disable the pch bios lock enable (ble bit) feature. Figure 4-4-7: bios security settings 4.4.8 sb porting configuration of pch-io sata raid rom legacy rom: legacy option ...

  • Page 86: 4.5   Security

    79 bios and driver setting set user password set hdd user password. *** advisable to power cycle system after setting hard disk passwords *** discard or save changes option in setup does not have any impact on hdd when password is set or removed. If the 'set hdd user password' option is gray, do pow...

  • Page 87: 4.6   Boot

    80 bios and driver setting ©vecow ecs-9700/ 9600 gtx1050 user manual 4.6 boot figure 4-6: bios boot menu setup prompt timeout number of seconds to wait for setup activation key. 65535(0xffff) means indefinite waiting. Bootup numlock state select the keyboard numlock state. Quiet boot enables or disa...

  • Page 88: 4.7   Save & Exit

    81 bios and driver setting 4.7 save & exit figure 4-7: bios save and exit menu save changes and exit exit system setup after saving the changes. Discard changes and exit exit system setup without saving any changes. Save changes and reset reset the system after saving the changes. Discard changes an...

  • Page 89: A.1   Function Description

    82 ©vecow ecs-9700/ 9600 gtx1050 user manual appendix a a appendix a : isolated dio guide pin no. Definition description pin no. Definition description 1 ext_in0 di0 11 ext_out0 do0 2 ext_in1 di1 12 ext_out1 do1 3 ext_in2 di2 13 ext_out2 do2 4 ext_in3 di3 14 ext_out3 do3 5 ext_in4 di4 15 ext_out4 do...

  • Page 90: Poe

    83 appendix a port no. Definition port no. Definition lan 3 poe 0 lan 5 poe 2 lan 4 poe 1 lan 6 poe 3 poe definition is shown below: do not use these functions in below: 1. Pe-2000: dio1 (id = 0), poe 2. Se-1000: poe 3. Ue-1000: usb (id = 0) lan6 poe lan5 poe lan4 poe lan3 poe isolated dio jumper se...

  • Page 91

    84 ©vecow ecs-9700/ 9600 gtx1050 user manual appendix a a.2 isolated dio signal circuit di reference circuit: sink mode (npn) v+ v- power supply 6-48v dc di_com (pin 9) di (pin1-8) dio connector source mode (pnp) v+ v- power supply 6-48v dc di_com (pin 9) di (pin1-8) dio connector do reference circu...

  • Page 92

    85 appendix a a.3 software package contain distribution folder include x32 and x64 versions, use batch file for installation. There are included as fallowed: win7_32.Bat: installation for 32-bit driver win7_64.Bat: windows update package which driver required (need to restart), and installation for ...

  • Page 93: A.4   Sample

    86 ©vecow ecs-9700/ 9600 gtx1050 user manual appendix a sample ecs9k7.Exe, as shown below: a.4 sample sample folder includes x32 and x64 versions, shown as below:.

  • Page 94

    87 appendix a dio1 / dio2 group: isolate check button: dio type of dio configuration, isolated / non-isolated, defined in ecs-9000 series user manual. Read button: set dio configuration to get di / dio input state. Do type check button: user setting, do type of dio configuration to setup 8 pins - so...

  • Page 95

    88 ©vecow ecs-9700/ 9600 gtx1050 user manual appendix a wdt setup text: user setting, wdt value, unit: second. Use for write button activate. Wdt counting text (read only): wdt counting by program timer after set wdt. Shown after write button action. Wdt setup day format texts (user setting): user s...

  • Page 96: B.1   Driver Api Guide

    89 appendix b b appendix b : software functions b.1 driver api guide in runtime folder, on ecs9k7.H: _dll_import_ definition is used on loadlibrary api for ecs9k7.Dll. Ecs9k_exports definition is used on ecs9k7.Dll building. Otherwise, that is used to compile with ecs9k7.Lib. Bool initial(byte isola...

  • Page 97

    90 ©vecow ecs-9700/ 9600 gtx1050 user manual appendix b bool setdio1config(byte *isolate_type, byte *di_npn, byte *do_npn, word *mask) bool setdio2config(byte *isolate_type, byte *di_npn, byte *do_npn, word *mask) set dio configuration isolate_type: dio type 1: isolated dio; 0: non-isolated dio di_n...

  • Page 98

    91 appendix b bool getdio1(word *di) bool getdio2(word *di) get non-isolated dio input (dio input) di ([15:0]): input state, pin setting by hexadecimal bitmask 1: high; 0: low return: true (1): success; false (0): fail (initial error, or call by pointer error, or hardware problem) bool setdio1(word ...

  • Page 99

    92 ©vecow ecs-9700/ 9600 gtx1050 user manual appendix b 1: enable; 0: disable return: true (1): success; false (0): fail (initial error, or call by pointer error, or hardware problem) bool setpoeconfig(byte auto, byte mask) set poe configuration auto ([3:0]): auto mode, pin setting by hexadecimal bi...

  • Page 100: C.1   Sata Mode For Raid

    93 appendix c c appendix c : raid installation guide c.1 sata mode for raid please select sata device to raid mode on bios menu. Advanced → sata configuration → sata mode selection c.2 os installation ecs-9700/9600 gtx1050 is featured with eight sata, option 1: include four internal sata, three msat...

  • Page 101: Technology” Software

    94 ©vecow ecs-9700/ 9600 gtx1050 user manual appendix c c.4 install “intel rapid storage technology” software you can get the software on ecs-9700/9600 gtx1050 driver cd. Also, you can find latest information and software directly from intel website. Http://www.Intel.Com/p/en_us/support/highlights/c...

  • Page 102

    95 appendix c then add “logical device” for windows access. C.7 disk management : partition the disk after raid 1 volume created, you can see the figure of sata device allocation. To start disk management tool, select "initialize disk." you will find “volume_0000” in sata device at bios menu. C.8 if...

  • Page 103: Different

    96 ©vecow ecs-9700/ 9600 gtx1050 user manual appendix c c.10 recovery and auto re-build when using different raid hdd there is a warning will pop-up to ask you if the disk is not a member of original raid volume. If you press “rebuild”, it will replace the broken sata hdd to the last one sata hdd of...

  • Page 104

    97 appendix d d appendix d : power consumption testing board ecs-9700 gtx1050 ram 8gb x 2 usb-1 usb keyboard logitech m105 usb-2 usb mouse microsoft 1113 usb-3 usb flash transecnd 3.0 8gb usb-4 usb flash transecnd 3.0 8gb cfast innodisk cfast 3me 32gb sata 0 memxpro sata m3a 256gb lan 1 (i219) 1.0 g...

  • Page 105

    98 ©vecow ecs-9700/ 9600 gtx1050 user manual appendix d d.1 intel® e3-1505m v5 (8m cache, 2.80 ghz) cpu power input standby mode sleep mode idle status : cpu usage less 3% max current max consumption max current max consumption max current max consumption intel ® e3- 1505m v5 10v 0.384a 03.84w 0.436...

  • Page 106: Storage List

    99 appendix e e appendix e : supported memory & storage list testing board ecs-9700 gtx1050 memory test version: 5.1 burnintest v8.1 e.1 supported memory list channel memory test burn in flash bios remove battery *2 pass pass pass pass *1(socket 1) pass pass n/a pass *1(socket 2) pass pass n/a pass ...

  • Page 107: E.3  Non-Ecc

    100 ©vecow ecs-9700/ 9600 gtx1050 user manual appendix e brand info channel note & s test temp. (celsius) transcend 8g 2rx8 ddr4 2400 so *2 ts9cbsese0000 25ºc *1(socket 1) c96645-0001 25ºc *1(socket 2) c96645-0002 25ºc transcend 16g 2rx8 ddr4 2133 so *2 ts0casgsb0000 25ºc *1(socket 1) d20478-0004 ...

  • Page 108: E.4  Ecc

    101 appendix e e.4 ecc brand info channel note & s test temp. (celsius) transcend 16gb ecc wild temp. *2 85ºc *1(socket 1) c94147-0001 85ºc *1(socket 2) c94147-0002 85ºc transcend 16g 2rx8 ddr4 2133 eccso *2 25ºc *1(socket 1) c69768-0063 25ºc *1(socket 2) c69768-0064 25ºc transcend 4g 1rx8 ddr4 21...

  • Page 109

    102 ©vecow ecs-9700/ 9600 gtx1050 user manual appendix e type brand model capacity msata intel intel-310 ssdmaemc080g2 80gb innodisk msata 3me3 demsr- 64gd09bw2dc 64gb msata 3me3 demsr- a28d09bw2dc 128gb msata 3me3 demsr- b56d08bwbqc 256gb sata ssd transcend ssd420 ts128gssd420i 128gb ssd420 ts256gs...

  • Page 110

    103 appendix f ** if more help is needed, please contact vecow technical support ** f appendix f : graphics performance test temperature (based on 95% humidity) 30ºc 35ºc 40ºc 45ºc 50ºc 55ºc 60ºc 3dmark 11 (v1.5.5.0) score x3390 x3378 x3352 x3205 x2997 x2878 x2853 resolution 1920 x 1080 highest temp...

  • Page 111

    For further support information, please visit www.Vecow.Com this document is released for reference purpose only. All product offerings and specifications are subject to change without prior notice. No part of this publication may be reproduced in any form or by any means, electric, photocopying, or...