1. DL manuals
  2. Vecow
  3. Computer Hardware
  4. ECS-9600
  5. User manual

Vecow ECS-9600 User manual

Manual is about: Quad Core Intel Xeon / Core i7/ i5/ i3 Fanless Embedded System High Performance, Rugged, Expandable, Extended Temperature

Summary of ECS-9600

  • Page 1

    User manual user manual 1.1.0 edition 20161114 ecs-9700/9600 quad core intel ® xeon ® / core ™ i7/ i5/ i3 fanless embedded system high performance, rugged, expandable, extended temperature.

  • Page 2: Record of Revision

    Ii version date page description remark 1.0 11/14/2016 all official release record of revision.

  • Page 3: Fcc

    Iii this manual is released by vecow co., ltd. For reference purpose only. All product offerings and specifications are subject to change without prior notice. It does not represent commitment of vecow co., ltd. Vecow shall not be liable for direct, indirect, special, incidental, or consequential da...

  • Page 4: Order Information

    Iv part number description ecs-9710-505m ecs-9700, quad core intel ® xeon ® e3-1505m v5, 6 gige lan w/ 4 poe + , 2 ssd tray, 1 pcie x16, 6 usb 3.0, 4 com, 4 sim, 32 isolated dio ecs-9710-820q ecs-9700, quad core intel ® core™ i7-6820eq, 6 gige lan w/ 4 poe + , 2 ssd tray, 1 pcie x16, 6 usb 3.0, 4 co...

  • Page 5: Order Accessories

    V part number description ddr4 16g certified ddr4 16gb 2133mhz ram ddr4 8g certified ddr4 8gb 2133mhz ram ddr4 4g certified ddr4 4gb 2133mhz ram pwa-280wb-wt 280w, 24v, 85v ac to 264v ac power adaptor with 3-pin terminal block (7.62mm pitch), wide temperature -30°c to +70°c pwa-160wb-wt 160w, 24v, 8...

  • Page 6: Table of Contents

    Vi table of contents chapter 1 general introduction 1 1.1 overview 1 1.2 features 2 1.3 product specification 2 1.3.1 specifications of ecs-9710 2 1.3.2 specifications of ecs-9701 4 1.3.3 specifications of ecs-9610 7 1.3.4 specifications of ecs-9601 9 1.4 supported cpu list 11 1.5 mechanical dimensi...

  • Page 7: Chapter   4

    Vii 3.5 installing sim card 58 3.6 installing pci/ pcie card 59 3.7 installing ssd/ hdd 61 3.8 mounting your ecs-9700/9600 63 chapter 4 bios setup 69 4.1 entering bios setup 69 4.2 main 70 4.3 advanced 70 4.4 chipset 80 4.5 security 85 4.6 boot 86 4.7 save & exit 87 appendix a : isolated dio guide 8...

  • Page 8: General Introduction

    1 general introduction 1 general introduction vecow ecs-9700/9600 series is a high-performance, all-in-one integrated, expandable fanless embedded system. Powered by 6th generation quad core intel ® xeon ® / core™ processor (skylake-h) running with advanced intel ® cm236 chipset, dual channel ddr4 2...

  • Page 9: 1.2   Features

    2 general introduction ©vecow ecs-9700/ 9600 user manual 1.2 features • quad core intel ® xeon ® / core™ i7/ i5/ i3 processor (skylake-h) with cm236 chipset supports up to 4k display • 2 ddr4 2133mhz memory, up to 32gb • fanless, -25°c to 70°c operating temperature • 6 gige lan with 4 ieee 802.3at p...

  • Page 10

    3 general introduction pci/ pcie 1 pcie x16 slot sumit a, b 2 sumit slot (optional) graphics graphics processor intel ® hd graphics p530/ 530 interface • vga : up to 1920 x 1200 @ 60hz • dvi-d : up to 1920 x 1200 @ 60hz • displayport 1 : up to 4096 x 2304 @ 60hz • displayport 2 : up to 4096 x 2304 @...

  • Page 11

    4 general introduction ©vecow ecs-9700/ 9600 user manual smart management wake on lan, pxe supported hw monitor monitoring temperature, voltages. Auto throttling control when cpu overheats. Software support os windows 10, windows 8.1, windows 7, linux mechanical dimensions (wxdxh) 260mm x 215mm x 79...

  • Page 12

    5 general introduction i/o interface serial 4 com rs-232/ 422/ 485 w/ auto flow control usb • 6 usb 3.0 (external) • 1 usb 2.0 (internal) isolated dio 32 isolated dio (16 di, 16 do) led power, hdd, wireless, poe sim card 4 sim card socket (3 external, 1 internal) expansion mini pcie 4 mini pcie sock...

  • Page 13

    6 general introduction ©vecow ecs-9700/ 9600 user manual lan 5 gige ieee 802.3at (25.5w/48v) poe + by intel ® i210 lan 6 gige ieee 802.3at (25.5w/48v) poe + by intel ® i210 power input voltage 6v to 36v, dc-in power interface 3-pin terminal block : v+, v-, frame ground ignition control 16 mode (inte...

  • Page 14

    7 general introduction 1.3.3 specifications of ecs-9610 system processor quad core intel ® xeon ® e3-1505m v5/ core™ i7-6820eq/ i5-6440eq processor (skylake-h) chipset intel ® cm236 bios ami sio it8786e memory • ddr4 2133mhz • up to 32gb • 2 260-pin so-dimm socket i/o interface serial 4 com rs-232/ ...

  • Page 15

    8 general introduction ©vecow ecs-9700/ 9600 user manual audio audio codec realtek alc892, 5.1 channel hd audio audio interface 1 mic-in, 1 line-out ethernet lan 1 intel ® i219lm gige lan supports iamt 11.0 lan 2 intel ® i210 gige lan power input voltage 6v to 36v, dc-in power interface 3-pin termin...

  • Page 16

    9 general introduction 1.3.4 specifications of ecs-9601 system processor quad core intel ® xeon ® e3-1505m v5/ core™ i7-6820eq/ i5-6440eq processor (skylake-h) chipset intel ® cm236 bios ami sio it8786e memory • ddr4 2133mhz • up to 32gb • 2 260-pin so-dimm socket i/o interface serial 4 com rs-232/ ...

  • Page 17

    10 general introduction ©vecow ecs-9700/ 9600 user manual audio audio codec realtek alc892, 5.1 channel hd audio audio interface 1 mic-in, 1 line-out ethernet lan 1 intel ® i219lm gige lan supports iamt 11.0 lan 2 intel ® i210 gige lan power input voltage 6v to 36v, dc-in power interface 3-pin termi...

  • Page 18: 1.4   Supported Cpu List

    11 general introduction 1.4 supported cpu list processor no. Tdp cache max. Frequency embedded xeon ® e3-1575m v5 45w 8m up to 3.00 ghz xeon ® e3-1545m v5 45w 8m up to 2.90 ghz xeon ® e3-1535m v5 45w 8m up to 2.80 ghz xeon ® e3-1515m v5 45w 8m up to 2.80 ghz xeon ® e3-1505m v5 45w 8m up to 2.80 ghz ...

  • Page 19: 1.5   Mechanical Dimension

    12 general introduction ©vecow ecs-9700/ 9600 user manual 1.5 mechanical dimension 1.5.1 dimensions of ecs-9710/9701 260.0 (10.24”) 282.0 (11.10”) 297.0 (11.69”) 155.0 (6.10”) 215.0 (8.46”) 79.1 (3.1 1”) unit: mm (inch) 1.5.2 dimensions of ecs-9610/9601 260.0 (10.24”) 282.0 (11.10”) 297.0 (11.69”) 1...

  • Page 20: 2.1   Packing List

    13 getting to know your ecs-9700/ 9600 2 getting to know your ecs-9700/9600 2.1 packing list item description qty 1 ecs-9700/9600 expandable fanless embedded system (according to the configuration you order, the ecs-9700/9600 series may contain ssd/hdd and ddr4 so-dimm. Please verify these items if ...

  • Page 21

    14 getting to know your ecs-9700/ 9600 ©vecow ecs-9700/ 9600 user manual 2.2 front panel i/o & functions in vecow ecs-9700/9600 series family, all i/o connectors are located on front panel and rear panel. Most of the general connections to computer device, such as usb, lan jack, audio, vga, display,...

  • Page 22

    15 getting to know your ecs-9700/ 9600 pin no. Description pin no. Description s1 gnd pc6 nc s2 sata_txp5 pc7 gnd s3 sata_txn5 pc8 cfast_led s4 gnd pc9 nc s5 sata_rxn5 pc10 nc s6 sata_rxp5 pc11 nc s7 gnd pc12 nc 2.2.3 cfast card there is a cfast socket on the front panel supporting type-i/ii compact...

  • Page 23

    16 getting to know your ecs-9700/ 9600 ©vecow ecs-9700/ 9600 user manual pin no. Description pin no. Description pc1 gnd pc13 +3.3v pc2 gnd pc14 +3.3v pc3 nc pc15 gnd pc4 nc pc16 gnd pc5 nc pc17 nc 2.2.4 pwr and hdd led indicator hdd led/ yellow: a hard disk/ cfast led. If the led is on, it indicate...

  • Page 24

    17 getting to know your ecs-9700/ 9600 the dvi-d connector on the front panel supports dvi display. This connector can output dvi signal. The dvi output mode supports up to 1920 x 1200 resolution and the dvi is automatically selected according to the display device connected. You will need a dvi-d c...

  • Page 25

    18 getting to know your ecs-9700/ 9600 ©vecow ecs-9700/ 9600 user manual 2.2.8 usb 3.0 there are 4 usb 3.0 connections available supporting up to 5gb per second data rate in the front side of ecs-9700/9600. It is also compliant with the requirements of super speed (ss), high speed (hs), full speed (...

  • Page 26

    19 getting to know your ecs-9700/ 9600 each lan port is supported by standard rj-45 connector with led indicators to present active/ link/ speed status of the connection. The led indicator on the right bottom corner lightens in solid green when the cable is properly connected to a 100 mbps ethernet ...

  • Page 27

    20 getting to know your ecs-9700/ 9600 ©vecow ecs-9700/ 9600 user manual 2.2.11 wlan led, mini pcie, sim card comparison rst dp lan 1 lan 2 dvi-d vga cfast sim 1 sim 3 sim 2 1 2 3 4 wlan mini pcie sim led mini pcie 1 / msata (cn12) sim 1 (cn13) 1 mini pcie 2 / msata (cn8) sim 2 (cn9) 2 mini pcie 3 /...

  • Page 28

    21 getting to know your ecs-9700/ 9600 hdd tray mb connector mb power connector hdd 1 sata1 power conn 1 hdd 2 sata2 power conn 1 sata3 power conn 2 sata4 (remark: by mb bom optional, default no signal link) power conn 2 2.2.12 ssd/ hdd tray there are 2 front-access 2.5” ssd/ hdd trays in the front ...

  • Page 30

    23 getting to know your ecs-9700/ 9600 serial port pin no. Rs-232 rs-422 (5-wire) rs-422 (9-wire) rs-485 (3-wire) 1 to 4 1 dcd txd- txd- data- 2 rxd txd+ txd+ data+ 3 txd rxd+ rxd+ ----------- 4 dtr rxd- rxd- ----------- 5 gnd gnd gnd gnd 6 dsr ----------- rts- ----------- 7 rts ----------- rts+ ---...

  • Page 31

    24 getting to know your ecs-9700/ 9600 ©vecow ecs-9700/ 9600 user manual com3 & com 4 mb connector table: com port mb connector com port mb connector com 3 cn27 com 4 cn28 cn pin no. Signal name cn27(com3) cn28(com4) 1 chassis gnd 2 gnd 3 ri 4 dtr 5 cts 6 txd 7 rts 8 rxd 9 dsr 10 dcd com 3 & com 4 m...

  • Page 32

    25 getting to know your ecs-9700/ 9600 2.3.5 poe (power over ethernet) ports there are 4 8-pin poe rj-45 jacks supporting 10/100/1000 mbps ethernet connections in the front side powered by intel i210 ethernet engine. When both lan 1 and lan 2 work in normal status, iamt 11.0 function is enabled. Eac...

  • Page 33

    26 getting to know your ecs-9700/ 9600 ©vecow ecs-9700/ 9600 user manual each lan port is supported by standard rj-45 connector with led indicators to present active/ link/ speed status of the connection. The led indicator on the right bottom corner lightens in solid green when the cable is properly...

  • Page 35

    28 getting to know your ecs-9700/ 9600 ©vecow ecs-9700/ 9600 user manual dio pin no. Definition function dio2 1 input 8 sio_gpi37 2 input 9 sio_gpi50 3 input 10 sio_gpi51 4 input 11 sio_gpi52 5 input 12 sio_gpi56 6 input 13 sio_gpi57 7 input 14 sio_gpi64 8 input 15 sio_gpi65 9 di2_com - 10 dio2_gnd ...

  • Page 37

    30 getting to know your ecs-9700/ 9600 ©vecow ecs-9700/ 9600 user manual 2.4 main board expansion connectors 2.4.1 inside view of ecs-9700 main board with connector location fn1 sata1 sata2 cn27 cn5 cn28 jp2 j9 j8 sata3 sata4 cn1 sw2 jp7 jp10 jp8 cn2 j10 sw5 jp11 sw7 sw11 cn20 cn3 jp1 jp3 bat j11 su...

  • Page 38

    31 getting to know your ecs-9700/ 9600 2.4.2 ups power connector for ups module optional, we use 4.2mm 2x2p power connector. This system has a ups power input connector for optional part ups module. Pin no. Definition pin no. Definition 1 ground 2 ground 3 +vdc_in (6~36v, max.8a) 4 +vdc_in (6~36v, m...

  • Page 39

    32 getting to know your ecs-9700/ 9600 ©vecow ecs-9700/ 9600 user manual group pin no. Description hdd led 1 hdd_led_p 3 hdd_led_n reset button 5 fp_rst_btn_n 7 ground power led 2 pwr_led_p 4 pwr_led_n power button 6 fp_pwr_btn_in 8 ground 2.4.4 ddr4 slot there are 2 ddr4 channel onboard and support...

  • Page 40

    33 getting to know your ecs-9700/ 9600 2.4.5 bios socket if the bios needs to be changed, please contact the vecow rma service team. Cn1 2.4.6 sata connector standard 7 pin sata connector there are 4 onboard high performance serial ata iii. It supports higher storage capacity with less cabling effor...

  • Page 41

    34 getting to know your ecs-9700/ 9600 ©vecow ecs-9700/ 9600 user manual 2.4.7 sata power header standard, all form factor 1x4p power header there are 2 hdd power header on board and each power header supports two 2.5” sata hdd. Pin no. Description pin no. Description 1 +v5 (max. 4a) 2 ground 3 grou...

  • Page 42

    35 getting to know your ecs-9700/ 9600 2.4.9 sumit a, sumit b this system has standard sumit a and sumit b for sumit type add on cards. Sumitb sumita pin no. Definition pin no. Definition 1 usb +vcc (+v5/max. 0.5a) 2 data- 3 data+ 4 ground cn20

  • Page 43

    36 getting to know your ecs-9700/ 9600 ©vecow ecs-9700/ 9600 user manual pin no. Function pin no. Function 1 +5v_aux 2 +12v 3 +3.3v 4 smb_data 5 +3.3v 6 xmb_clk 7 reserved 8 reserved 9 reserved 10 spi_miso 11 usb_oc# 12 spi_mosi 13 reserved 14 spi_clk 15 +5v 16 spi_cs10 17 usb_3+ 18 spi_cs1# 19 usb_...

  • Page 44

    37 getting to know your ecs-9700/ 9600 pin no. Function pin no. Function 1 gnd 2 gnd 3 b_pet_p0 4 b_per_p0 5 b_pet_n0 6 b_per_n0 7 gnd 8 gnd 9 c_clkp 10 b_clkp 11 c_clkn 12 b_clkn 13 cprsnt#/c_pe_clkreq# 14 gnd 15 c_pet_p0 16 c_per_p0 17 c_pet_n0 18 c_per_n0 19 gnd 20 gnd 21 c_pet_p1 22 c_per_p1 23 ...

  • Page 45

    38 getting to know your ecs-9700/ 9600 ©vecow ecs-9700/ 9600 user manual 2.4.10 mini pcie/ msata slot cn6 cn10 cn12 cn8 sw2 mini pcie and msata share the same form factor and similar electrical pinout assignments on their connectors. There is no clear mechanism to distinguish if a msata drive or a m...

  • Page 46

    39 getting to know your ecs-9700/ 9600 pin no. Function pin no. Function 51 reserved 52 +3.3vaux 49 reserved 50 gnd 47 reserved 48 +1.5v 45 reserved 46 reserved 43 gnd 44 reserved 41 +3.3vaux 42 reserved 39 +3.3vaux 40 gnd 37 gnd 38 usb_d+ 35 gnd 36 usb_d- 33 petp0 34 gnd 31 petn0 32 smb_data 29 gnd...

  • Page 47

    40 getting to know your ecs-9700/ 9600 ©vecow ecs-9700/ 9600 user manual 2.4.11 rtc battery the system’s real-time clock is powered by a lithium battery. It is equipped with panasonic br2032 190mah lithium battery. It is recommended that you do not have to get the lithium battery on your own. If the...

  • Page 48

    41 getting to know your ecs-9700/ 9600 pin no. Function pin no. Function 1 serirq 7 lframe# 2 +3.3v 8 lad0 3 la3 9 n/c 4 reset# 10 ground 5 lad1 11 clock 6 lad2 12 ground pin out: 2.4.13 lpc port 80 header ecs-9700 provides a lpc port 80 header for debug card. Cn3 2.4.14 lan ieee 1588 header ecs-970...

  • Page 49

    42 getting to know your ecs-9700/ 9600 ©vecow ecs-9700/ 9600 user manual j9 j8 j7 j6 jp3 pin no. Function pin no. Function 1 spd0 2 spd1 3 spd2 4 spd3 5 ground 6 ground pin out:.

  • Page 50

    43 getting to know your ecs-9700/ 9600 2.4.15 com port header ecs-9700 provides 4 com port headers for internal com port cable. Pin no. Description port 1 ground_frame com3 2 ground com3 3 ri com3 4 dtr com3 5 cts com3 6 txd com3 7 rts com3 8 rxd com3 9 dsr com3 10 dcd com3 cn27: pin no. Description...

  • Page 51

    44 getting to know your ecs-9700/ 9600 ©vecow ecs-9700/ 9600 user manual 2.5 main board jumper & deep switch settings 2.5.1 top view of ecs-9700 with jumper and deep switch the figure below is the top view of ecs-9700 board, and it shows the location of the jumpers and the switches. You may configur...

  • Page 52

    45 getting to know your ecs-9700/ 9600 you may configure your card to match the needs of your application by dip switch as shown below (the deep switch on and off) on 1 2 1 : off 2 : off on 1 2 1 : on 2 : off on 1 2 1 : on 2 : on 2.5.2 usb power jumper jumper setting function usb port jp3 1:2 non wa...

  • Page 53

    46 getting to know your ecs-9700/ 9600 ©vecow ecs-9700/ 9600 user manual 2.5.3 com port ri pin select pin header pin no. Description com1 jp5 1-2 +5v (1a max.) 3-4 +12v (0.5a max.) 5-6 ri (default) pin header pin no. Description com2 jp6 1-2 +5v (1a max.) 3-4 +12v (0.5a max.) 5-6 ri (default) pin he...

  • Page 54

    47 getting to know your ecs-9700/ 9600 2.5.4 com port rs-422/rs-485 receiver terminator sw3 sw4 com / dip switch on / off com rs-422/485 receiver terminator com1 / sw3-1 on *enable off disable com / dip switch on / off com rs-422/485 receiver terminator com2 / sw3-2 on *enable off disable com / dip ...

  • Page 55

    48 getting to know your ecs-9700/ 9600 ©vecow ecs-9700/ 9600 user manual 2.5.5 poe power on select jumper setting function jp9 1:2 poe power on at standby power ready jp9 2:3 poe power on after system power on (default) jp9 2.5.6 cmos & me clear function dip switch description sw 1-1 cmos clear sett...

  • Page 56: 2.6   Ignition Control

    49 getting to know your ecs-9700/ 9600 2.6 ignition control 2.6.1 adjust ignition control modes ecs-9700 series provides ignition power control feature for in-vehicle applications. The built-in mcu monitors the ignition signal and turns on/off the system according to pre-defined on/off delay periods...

  • Page 57

    50 getting to know your ecs-9700/ 9600 ©vecow ecs-9700/ 9600 user manual the modes are listed in the following table: item power on delay power off delay switch position 0 atx mode 1 no delay no delay 2 no delay 5 seconds 3 no delay 10 seconds 4 no delay 20 seconds 5 5 seconds 30 seconds 6 5 seconds...

  • Page 58

    51 getting to know your ecs-9700/ 9600 2.6.2 ignition control wiring to activate ignition control, you need to provide ign signal via the 3-pin pluggable terminal block located in the back panel. It is below the general wiring configuration. For testing purpose, you can refer to the picture above to...

  • Page 59: System Setup

    52 hardware installation ©vecow ecs-9700/ 9600 user manual system setup 3.1 how to open your ecs-9700/9600 3 step 1 remove hole plugs. Step 2 remove two f#6-32 screws (circled in red) and two f-m3 screws (circled in yellow) on the bottom side..

  • Page 60

    53 hardware installation step 3 finish step1 and 2. Step 4 remove one khs#6-32x6 screws(red) and cover(yellow)..

  • Page 61

    54 hardware installation ©vecow ecs-9700/ 9600 user manual step 6 finish. Step 5 open the module..

  • Page 62

    55 hardware installation 3.2 installing ddr4 so-dimm modules step 1 ddr4 ram module into so-dimm slot. Step 2 make sure the ram module is locked by the memory slot..

  • Page 63

    56 hardware installation ©vecow ecs-9700/ 9600 user manual 3.3 installing mini pcie card step 1 install mini pcie card into the mini pcie socket. Step 2 fasten one m2.5 screw..

  • Page 64: 3.4   Installing Cfast Card

    57 hardware installation 3.4 installing cfast card step 1 remove 2 pcs f-m3x4 screws on cfast & sim card. Step 2 before inserting cfast & sim card, make sure ecs-9700 power is not plugged. Step 3 insert cfast card and push to lock. Step 4 insert cf card and push to lock..

  • Page 65: 3.5   Installing Sim Card

    58 hardware installation ©vecow ecs-9700/ 9600 user manual 3.5 installing sim card step 1 remove 2 pcs f-m3x4 screws on cfast & sim card. Step 2 before inserting cfast & sim card, make sure ecs-9700 power is not plugged. Step 3 insert cfast card and push to lock. Step 4 insert sim card and push to l...

  • Page 66

    59 hardware installation 3.6 installing pci/ pcie card step 2 remove the bracket. Step 1 remove the m3 screw..

  • Page 67

    60 hardware installation ©vecow ecs-9700/ 9600 user manual step 4 fasten m3 screw. Step 3 installing pci/pcie card..

  • Page 68: 3.7   Installing Ssd/ Hdd

    61 hardware installation 3.7 installing ssd/ hdd step 1 trigger and open ssd/hdd tray. Step 2 insert 2.5” ssd/hdd in the tray and fasten two f-m3x4 screws..

  • Page 69

    62 hardware installation ©vecow ecs-9700/ 9600 user manual step 3 finish. Step 4 installing ssd/hdd..

  • Page 70

    63 hardware installation 3.8 mounting your ecs-9700/9600 step 1 ensure the screw holes on the right and left side of the upper case match the ones on ecs-9700/9600 wall mount bracket. 3.8.1 wall mount bracket.

  • Page 71

    64 hardware installation ©vecow ecs-9700/ 9600 user manual step 2 fasten 4pcs khs#6-32 screws then finish..

  • Page 72

    65 hardware installation 3.8.2 vesa mount step 1 ecs-9700/9600 and vesa mount. Step 2 take ecs-9700/9600 and vesa mount with fasten 4pcs khs#6-32 screws..

  • Page 73

    66 hardware installation ©vecow ecs-9700/ 9600 user manual step 3 fasten four khs#6-32 screws and then finish. Step 4 finish. Step 5 vesa size have 75x75mm(red) and 100x100mm(yellow)..

  • Page 74

    67 hardware installation 3.8.3 din rail kit step 1 ecs-9700/9600 and din rail kit. Step 2 take ecs-9700/9600 and din rail kit and fasten four khs#6-32 screws in the four marked corners..

  • Page 75

    68 hardware installation ©vecow ecs-9700/ 9600 user manual step 3 fasten four khs#6-32 screws and then finish. Step 4 finish. Step 5 ecs-9700/9600 with din rail..

  • Page 76: Bios Setup

    69 bios and driver setting 4 bios setup 4.1 entering bios setup bios provides an interface for users to check and change system configuration. The bios setup program is accessed by pressing the key when post display output is shown. Figure 4-1: entering setup screen.

  • Page 77: 4.2   Main

    70 bios and driver setting ©vecow ecs-9700/ 9600 user manual 4.2 main the main menu displays bios version and system information. There are two options on main menu. System date set the date. Use to switch between date elements. System time set the time. Use to switch between time elements. Figure 4...

  • Page 78

    71 bios and driver setting 4.3.1 trusted computing control the tpm device status and display related information if tpm chip is present. Figure 4 3-1: trusted computing 4.3.2 acpi settings enable hibernation enables or disables system's ability to hibernate (os/s4 sleep state). This option may not b...

  • Page 79

    72 bios and driver setting ©vecow ecs-9700/ 9600 user manual 4.3.4 pch-fw configuration me unconfig on rtc clear state disabling this option will cause me not to unconfigure on rtc clear. Me state set me to soft temporarily disabled. Figure 4 3-4: pch-fw settings 4.3.5 smart settings smart self test...

  • Page 80

    73 bios and driver setting 4.3.6 it8786 super io configuration figure 4-3-6-1: super io settings set the direction of the gpio pins creates bios options for end user to change internal gpio pin direction. Figure 4 3-6-3: gpio pin input/output settings of sio it8786 figure 4-3-6-2: serial port settin...

  • Page 81

    74 bios and driver setting ©vecow ecs-9700/ 9600 user manual 4.3.8 serial port console redirection console redirection console redirection enable or disable. Console redirection settings these settings specify how the host computer and the remote computer (which the user is using) will exchange data...

  • Page 82

    75 bios and driver setting hyper-threading enabled for windows xp and linux (os optimized for hyper-threading technology) and disabled for other os (os not optimized for hyper-threading technology). When disabled only one thread per core is enabled. Active processor cores number of cores to enable i...

  • Page 83

    76 bios and driver setting ©vecow ecs-9700/ 9600 user manual 4.3.10 intel txt information display intel txt information. Figure 4 3-10: intel txt information 4.3.11 sata configuration figure 4 3-11: sata devices settings cpu c state enable or disable cpu c states. Enhanced c-states enable/disable c1...

  • Page 84

    77 bios and driver setting sata controller(s) enable or disable sata device. Sata mode selection determines how sata controller(s) operate. Software feature mask configuration raid orom/rst driver will refer to the swfm configuration to enable or disable the storage features. Aggressive lpm support ...

  • Page 85

    78 bios and driver setting ©vecow ecs-9700/ 9600 user manual 4.3.13 csm configuration csm support enable/disable csm support gatea20 active upon request - ga20 can be disabled using bios services. Always - do not allow ga20 to be disabled; this option is useful when any rt code is executed above 1mb...

  • Page 86

    79 bios and driver setting 4.3.14 usb configuration legacy usb support enables legacy usb support. Auto option disables legacy support if no usb devices are connected. Disable option will keep usb devices available only for efi applications. Xhci hand-off this is a workaround for os-es without xhci ...

  • Page 87: 4.4   Chipset

    80 bios and driver setting ©vecow ecs-9700/ 9600 user manual vt-d vt-d capability. Gmm device (b0:d8:f0) enable/disable sa gmm device. Above 4gb mmio bios assignment enable/disable above 4gb memorymappedio bios assignment. This is disabled automatically when aperture size is set to 2048mb. 4.4.1 sys...

  • Page 88

    81 bios and driver setting 4.4.2 graphics configuration of system agent (sa) graphics turbo imon current graphics turbo imon current values supported (14-31). Skip scaning of external gfx card if enable, it will not scan for external gfx card on peg and pch pcie ports. Primary display select which o...

  • Page 89

    82 bios and driver setting ©vecow ecs-9700/ 9600 user manual 4.4.3 peg port configuration (sa) peg port options for pcie device. Figure 4-4-3: peg port configuration 4.4.4 memory information of system agent (sa) displays memory information. Figure 4-4-4: memory information 4.4.5 pch-io configuration...

  • Page 90

    83 bios and driver setting pch lan controller enable or disable onboard nic. Wake on lan enable or disable integrated lan to wake the system. (the wake on lan cannot be disabled if me is on at sx state.) serial irq mode configure serial irq mode. State after g3 specify what state to go to when power...

  • Page 91

    84 bios and driver setting ©vecow ecs-9700/ 9600 user manual 4.4.7 bios security configuration of pch-io bios lock enable/disable the pch bios lock enable (ble bit) feature. Figure 4-4-7: bios security settings 4.4.8 sb porting configuration of pch-io sata raid rom legacy rom: legacy option rom uefi...

  • Page 92: 4.5   Security

    85 bios and driver setting set user password set hdd user password. *** advisable to power cycle system after setting hard disk passwords *** discard or save changes option in setup does not have any impact on hdd when password is set or removed. If the 'set hdd user password' option is gray, do pow...

  • Page 93: 4.6   Boot

    86 bios and driver setting ©vecow ecs-9700/ 9600 user manual 4.6 boot figure 4-6: bios boot menu setup prompt timeout number of seconds to wait for setup activation key. 65535(0xffff) means indefinite waiting. Bootup numlock state select the keyboard numlock state. Quiet boot enables or disables qui...

  • Page 94: 4.7   Save & Exit

    87 bios and driver setting 4.7 save & exit figure 4-7: bios save and exit menu save changes and exit exit system setup after saving the changes. Discard changes and exit exit system setup without saving any changes. Save changes and reset reset the system after saving the changes. Discard changes an...

  • Page 95: A.1  I/o Pin Definition

    88 ©vecow ecs-9700/ 9600 user manual appendix a a a.1 i/o pin definition gpio pin base address usage 10, 13, 14, 17 0xa00 ----------- 11, 12, 15, 16 cn16-gpio 20 ~ 27 0xa01 ----------- 30, 31, 34 0xa02 ----------- 32, 33, 35 ~ 37 cn16-gpio 40 ~ 47 0xa03 ----------- 50 ~ 52, 56, 57 0xa04 cn16-gpio 53...

  • Page 96: A.2   Function Description

    89 appendix a pin no. Definition description pin no. Definition description 1 ext_in0 di0 11 ext_out0 do0 2 ext_in1 di1 12 ext_out1 do1 3 ext_in2 di2 13 ext_out2 do2 4 ext_in3 di3 14 ext_out3 do3 5 ext_in4 di4 15 ext_out4 do4 6 ext_in5 di5 16 ext_out5 do5 7 ext_in6 di6 17 ext_out6 do6 8 ext_in7 di7 ...

  • Page 97: A.3   Dio Signal Circuit

    90 ©vecow ecs-9700/ 9600 user manual appendix a a.3 dio signal circuit di reference circuit: sink mode (npn) v+ v- power supply 6-48v dc di_com (pin 9) di (pin1-8) dio connector source mode (pnp) v+ v- power supply 6-48v dc di_com (pin 9) di (pin1-8) dio connector do reference circuit: v+ io v- devi...

  • Page 98: A.5   Driver Install

    91 appendix a a.4 software package contain there are two folders with the following inside: ● driver folder includes x32 & x64 versions ● runtime folder includes dll and header file for software developer or system integration ● sample folder includes sample program a.5 driver install in driver fold...

  • Page 99

    92 ©vecow ecs-9700/ 9600 user manual appendix a on device manager, “vecow embedded io access” will be added. Please press any key to restart..

  • Page 100: A.6   Dio Demo Tool

    93 appendix a a.6 dio demo tool execute dio demo tool (ecs9k7.Exe). Operation on dio demo tool utility. Operation on dio / wdt / poe demo tool utility. Click “read” button to get value; input any number in write and write mask textbox, and click “write” button to set value. On dio panel, check the d...

  • Page 101: B.1   Iomem.Dll Api

    94 ©vecow ecs-9700/ 9600 user manual appendix b b appendix b : software functions b.1 iomem.Dll api kernel access for gpio, wdt & poe. Int outp(unsigned long port, unsigned char value); description: set byte-data to port. Return: if success return 1; else return 0. Unsigned char inp(unsigned int por...

  • Page 102

    95 appendix b return: if success return 1; else return 0. Int set_wdt(unsigned long time); description: set wdt time for wdt. Return: if success return 1; else return 0. Int get_poe(unsigned short *poei, unsigned short *func); description: get poe data. Return: if success return 1; else return 0. Ma...

  • Page 103: C.1   Sata Mode For Raid

    96 ©vecow ecs-9700/ 9600 user manual appendix c c appendix c : raid installation guide c.1 sata mode for raid please select sata device to raid mode on bios menu. Advanced → sata configuration → sata mode selection c.2 os installation ecs-9700/9600 is featured with eight sata, option 1: include four...

  • Page 104: Technology” Software

    97 appendix c c.4 install “intel rapid storage technology” software you can get the software on ecs-9700 driver cd. Also, you can find latest information and software directly from intel website. Http://www.Intel.Com/p/en_us/support/highlights/chpsts/imsm the raid environment has been done if you co...

  • Page 105

    98 ©vecow ecs-9700/ 9600 user manual appendix c then add “logical device” for windows access. C.7 disk management : partition the disk after raid 1 volume created, you can see the figure of sata device allocation. To start disk management tool, select "initialize disk." you will find “volume_0000” i...

  • Page 106: Different

    99 appendix c c.10 recovery and auto re-build when use different raid hdd there is a warning will pop-up to ask you if the disk is not a member of original raid volume. If you press “rebuild”, it will replace the broken sata hdd to the last one sata hdd of raid volume. C.9 recovery and auto re-build...

  • Page 107

    100 ©vecow ecs-9700/ 9600 user manual appendix d d appendix d : power consumption testing board ecs-9700 ram 16gb x 2 usb-1 usb keyboard logitech k120 usb-2 usb mouse microsoft 1113 usb-3 usb flash transecnd 3.0 8gb usb-4 usb flash transecnd 3.0 8gb cfast transcend cfast cfx600 64gb sata 0 transcedn...

  • Page 108

    101 appendix d d.1 intel® xeon® e3-1505m v5 (8m cache, 2.80 ghz) cpu power input standby mode sleep mode idle status : cpu usage less 3% max current max consumption max current max consumption max current max consumption xeon ® e3- 1505m v5 06v 0.650a 03.90w 0.770a 04.62w 3.800a 22.80w xeon ® e3- 15...

  • Page 109

    102 ©vecow ecs-9700/ 9600 user manual appendix d d.2 intel® core™ i7-6820eq (8m cache, 2.80 ghz) cpu power input standby mode sleep mode idle status : cpu usage less 3% max current max consumption max current max consumption max current max consumption core™ i7- 6820eq 06v 0.640a 03.84w 0.790a 04.74...

  • Page 110

    103 appendix d d.3 intel® core™ i5-6440eq (6m cache, 2.70 ghz) cpu power input standby mode sleep mode idle status : cpu usage less 3% max current max consumption max current max consumption max current max consumption core™ i5- 6440eq 06v 0.630a 03.78w 0.800a 04.80w 3.730a 22.38w core™ i5- 6440eq 0...

  • Page 111: Storage List

    104 ©vecow ecs-9700/ 9600 user manual appendix e e appendix e : supported memory & storage list testing board ecs-9700/9600 memory test version: 5.1 burnintest v8.1 e.1 supported memory list channel memtest bunin flash bios remove battery *2 pass pass pass pass *1(socket 1) pass pass n/a pass *1(soc...

  • Page 112: E.3  Non-Ecc

    105 appendix e brand info note & s test temp. (celsius) transcend 8gb 8g 2rx8 ddr4 2400 so ts9cbsese0000 25ºc c96645-0001 25ºc c96645-0002 25ºc transcend 16gb 16g 2rx8 ddr4 2133 so ts0casgsb0000 25ºc d20478-0004 25ºc d20478-0004 25ºc dsl ddr4 2133 4gb cl15 d4ss12081 sh21a-a 1614-35909 25ºc 1614-35...

  • Page 113: E.4  Ecc

    106 ©vecow ecs-9700/ 9600 user manual appendix e brand info note & s test temp. (celsius) transcend 16gb ecc wild temp. 16g 2rx8 ddr4 2133 eccso c94147-0001 85ºc c94147-0002 85ºc transcend 16gb ecc 16g 2rx8 ddr4 2133 eccso c69768-0063 25ºc c69768-0064 25ºc transcend 4gb ecc 4g 1rx8 ddr4 2133 eccso...

  • Page 114

    107 appendix e type brand model capacity msata intel intel-310 ssdmaemc080g2 80gb innodisk msata 3me3 demsr- 64gd09bw2dc 64gb msata 3me3 demsr- a28d09bw2dc 128gb msata 3me3 demsr- b56d08bwbqc 256gb sata ssd transcend ssd420 ts128gssd420i 128gb ssd420 ts256gssd420i 256gb ssd370 ts64gssd370 64gb intel...

  • Page 115

    For further support information, please visit www.Vecow.Com this document is released for reference purpose only. All product offerings and specifications are subject to change without prior notice. No part of this publication may be reproduced in any form or by any means, electric, photocopying, or...