Vector VEC1086B Owner's Manual & Warranty

Page of 8

Download

Print this page

Bookmark us

SMART AUTOMATIC

BATTERY CHARGER

OWNER’S MANUAL & WARRANTY INFORMATION

12 VOLT 2/4/6 AMPERE CHARGE RATES WITH

• IMPORTANT SAFETY INSTRUCTIONS •

WARNING – RISK OF EXPLOSIVE GASES

WARNING - RISK OF EXPLOSIVE GASES

1. WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES

GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS

REASON, IT IS OF UTMOST IMPORTANCE THAT EACH TIME BEFORE USING YOUR

CHARGER, YOU READ THIS MANUAL AND FOLLOW THE INSTRUCTIONS EXACTLY.

2. To reduce risk of battery explosion, follow these instructions and those published by the battery manufacturer

and manufacturer of any equipment you intend to use in vicinity of battery. Review cautionary markings on

these products and on engine.

GENERAL SAFETY

1. Use this charger for charging a LEAD-ACID battery only. It is not intended to supply power to a low voltage electrical

system other than in a starter-motor application. DO not use this battery charger for dry-cell batteries that are

commonly used with home appliances. These batteries may burst and cause injury to persons and damage to

property.

2. Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire,

electric shock, or injury to persons.

3. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger.

4. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in

a risk of fire and electric shock.

If extension cord must be used, make sure:

a. Pins on plug of extension cord are the same number, size, and shape as those of plug on charger.

b. Extension cord is properly wired and in good electrical condition; and

c. Wire size is AWG#14 (14 gauge) to 100 feet and AWG#12 for distances over 100 feet.

5. Do not operate charger with damaged cord or plug - take to a qualified service technician for replacement of the

cord or plug immediately.

6. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in anyway; take it to

a qualified service technician.

7. Do not disassemble charger; contact a qualified service technician when service or repair is required. Incorrect

reassembly may result in risk of electric shock or fire.

8. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning

off charger controls will not reduce this risk.

9. Do not operate charger in rain or snow or use when wet.

10. Never charge a frozen battery.

SAVE THESE INSTRUCTIONS:

This manual contains important safety and operating instructions for battery charger Model VEC1086B

4140 SW 28TH WAY, FT. LAUDERDALE, FL 33312 • TEL: 954-584-4446 • FAX: 954-584-5556 • TOLL-FREE 866-584-5504

VEC1086B

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

1 2 3 4 5 6 7 Next › »

Summary of VEC1086B

Page 1
Smart automatic battery charger owner’s manual & warranty information 12 volt 2/4/6 ampere charge rates with • important safety instructions • warning – risk of explosive gases warning - risk of explosive gases 1. Working in vicinity of a lead-acid battery is dangerous. Batteries generate explosive ...
Page 2: Power Cord Connection
2 personal precautions and safety 1. Another person should be close enough to come to your aid when you work near a lead-acid battery. 2. Fresh water and soap should be nearby in case battery acid contacts skin, clothing, or eyes. 3. Wear eye protection and protective clothing. Avoid touching eyes o...
Page 3
3 follow these steps when battery is installed in vehicle. A spark near battery may cause battery explosion. To reduce risk of a spark near battery: 1. Position ac and dc cords/cables to reduce risk of damage by hood, door, or other moving engine parts. 2. Stay clear of fan blades, belts, pulleys, a...
Page 4: Introduction and Features
4 introduction and features thank you for selecting the vector model vec1086b 2/4/6 amp 12 volt smart battery charger. With proper care and use, it will give you years of dependable service. This battery charger has a high charge rate of up to 6 amps, and low charge rate of up to 2 amps. It is desig...
Page 5: Controls and Indicators
5 figure 3 front view warnings: there are no user-serviceable parts in this charger. Do not open the unit! It must be returned to vector for professional testing and repair. Opening the unit will void the manufacturer's warranty. Contact the vector technical support department at (954) 584-4446 or t...
Page 6: Charge Rate Selection
Charge rate selection after charger clamps are correctly connected, plug in the charger to an ac outlet and the power indicator lights. Select proper charge current rate based on battery size. Press the 2/4/6 amp push button and the charger will begin charging at 2 amps. Pressing the 2/4/6 amp push ...
Page 7: Charging Times
7 internal short cell battery • if the battery being charged has an internal shorted cell, the fault led will light. • if fault led light comes on, vector recommends you take your battery to a certified automotive service center for evaluation. Battery not accepting a charge • make sure that the cha...
Page 8: Warranty
8 warranty this limited warranty program is the only one that applies to this product, and it sets forth all the responsibilities of vector manufacturing, ltd., regarding this product. There is no other warranty, other than described herein. This vector manufacturing, ltd. Product is warranted, to t...