1. DL manuals
  2. Vector
  3. Control Unit
  4. VX1000
  5. System Manual

Vector VX1000 System Manual

Manual is about: Measurement and Calibration Interface

Summary of VX1000

  • Page 2

    Imprint vector informatik gmbh ingersheimer straße 24 d-70499 stuttgart the information and data given in this user manual can be changed without prior notice. No part of this manual may be reproduced in any form or by any means without the written permission of the publisher, regardless of which me...

  • Page 3

    Contents vx1000 system manual version 3.3.0 3 contents 1 introduction 5 1.1 about this user manual 6 1.1.1 certification 7 1.1.2 warranty 7 1.1.3 support 7 1.1.4 registered trademarks 7 2 system overview 8 2.1 overview 9 2.2 vx1000 system components 10 2.3 supported microcontrollers 11 2.4 features ...

  • Page 4

    Contents vx1000 system manual version 3.3.0 4 3.4.4 status bar 30 3.4.5 message window 30 3.5 howto 32 3.5.1 vxtools installation 32 3.5.2 vx1000 system installation 32 3.5.3 vx1000 system ip configuration 33 3.5.3.1 change ip address 34 3.5.3.2 force ip address 35 3.5.4 fpga and firmware update 35 ...

  • Page 5: 1 Introduction

    1 introduction vx1000 system manual version 3.3.0 5 1 introduction in this chapter you find the following information: 1.1 about this user manual 6 1.1.1 certification 7 1.1.2 warranty 7 1.1.3 support 7 1.1.4 registered trademarks 7.

  • Page 6

    1 introduction vx1000 system manual version 3.3.0 6 1.1 about this user manual conventions in the two following charts you will find the conventions used in the user manual regarding utilized spellings and symbols. Style utilization bold blocks, surface elements, window- and dialog names of the soft...

  • Page 7: 1.1.1 Certification

    1 introduction vx1000 system manual version 3.3.0 7 1.1.1 certification certified quality management system vector informatik gmbh has iso 9001:2008 certification. The iso standard is a glob- ally recognized standard. 1.1.2 warranty restriction of warranty we reserve the right to change the contents...

  • Page 8: 2 System Overview

    2 system overview vx1000 system manual version 3.3.0 8 2 system overview in this chapter you find the following information: 2.1 overview 9 2.2 vx1000 system components 10 2.3 supported microcontrollers 11 2.4 features 12 2.5 vx1000 application driver and vx1000if 13.

  • Page 9: 2.1 Overview

    2 system overview vx1000 system manual version 3.3.0 9 2.1 overview at a glance the vx1000 system is a scalable solution with top performance for your meas- urement and calibration tasks. It can be used in the vehicle – both in the interior and in the engine compartment – on test benches and in the ...

  • Page 10

    2 system overview vx1000 system manual version 3.3.0 10 2.2 vx1000 system components base modules > vx1060 serial base module > vx1132 base module plug-on devices (pods) > vx1451 generic hssl pod (rtp/dmm, nexus aux) > vx1453 generic hssl pod (nexus aurora) > vx1543a serial pod (infineon, dap, jtag)...

  • Page 11

    2 system overview vx1000 system manual version 3.3.0 11 2.3 supported microcontrollers supported micro- controllers this section contains a list of all currently supported microcontroller families. Note please contact vector vx support (vxsupport@vector.Com) for further information about supported m...

  • Page 12: 2.4 Features

    2 system overview vx1000 system manual version 3.3.0 12 2.4 features overview > very high measurement data throughput of up to 50 mbyte/s with the data trace measurement method and up to 3 mbyte/s with the copying method > measurement of fast signal cycles (>10 µs for data trace, >40 µs for copying ...

  • Page 13

    2 system overview vx1000 system manual version 3.3.0 13 2.5 vx1000 application driver and vx1000if for the vx1000 measurement and calibration system, the vx1000 application driver must be integrated into the ecu application. The vx1000 application driver contains highly configurable, platform- and d...

  • Page 14: 3 Vxtools

    3 vxtools vx1000 system manual version 3.3.0 14 3 vxtools in this chapter you find the following information: 3.1 vxtools setup 15 3.1.1 overview 15 3.1.2 minimum requirements 15 3.1.3 installations instructions 15 3.2 vxconfig 16 3.2.1 general information 16 3.2.2 menu bar 17 3.2.3 toolbar 20 3.2.4...

  • Page 15: 3.1 Vxtools Setup

    3 vxtools vx1000 system manual version 3.3.0 15 3.1 vxtools setup 3.1.1 overview general information vxtoolssetup_.Exe is the setup program for the vector vxtools con- taining > vxconfig (configuration tool for the vx1000 system) > vxupdate (firmware and fpga update tool for the vx1000 system) > can...

  • Page 16: 3.2 Vxconfig

    3 vxtools vx1000 system manual version 3.3.0 16 3.2 vxconfig 3.2.1 general information configuration tool vxconfig is the configuration tool for the vx1000 system. This tool provides access to all vxparameters which control the behavior of the vx device. It also performs firmware and fpga updates us...

  • Page 17: 3.2.2 Menu Bar

    3 vxtools vx1000 system manual version 3.3.0 17 3.2.2 menu bar file menu > new virtual vx device… inserts a new virtual vx device into the device list, either by using vxparameter defaults or by importing vxparameters from a vxparameter file. > remove virtual vx device from device list the selected ...

  • Page 18

    3 vxtools vx1000 system manual version 3.3.0 18 commands menu > scan for vx devices scans the network for vx devices. Found devices are shown in the device list view. > reboot vx device restarts the selected vx device. > vx device info… shows details of the selected vx device. > identify vx device f...

  • Page 19

    3 vxtools vx1000 system manual version 3.3.0 19 > force ip address… sets the ip address of a vx device even if it cannot be found by a scan e.G. Due to a firewall problem. The vx device must be specified by base module type, serial number, and config xcp port. > open vxconsole … opens vxconsole to d...

  • Page 20: 3.2.3 Toolbar

    3 vxtools vx1000 system manual version 3.3.0 20 3.2.3 toolbar toolbar > scan scans the network for vx devices. Found devices are shown in the device list view. > broadcast sets the broadcast address for vx device scans. This parameter limits the scan to a subnet (e.G. To a single network adapter) or...

  • Page 22

    3 vxtools vx1000 system manual version 3.3.0 22 status description / possible problems > xcp slave is already in use by another xcp master (measurement tool). > check the vx device status. > base module type the base module type (e.G. Vx1132) is printed next to the device state symbol. > serial numb...

  • Page 24

    Vx1000 system manual version 3.3.0 24 note valid vximage file types for the vx1000 system are: .Vxp vxconfigurationset with a set of vxconfigurations consisting of vximage and vxparameter files. .Vxc vxcontainer with a set of vximage files for the vx1000 system. .Vxi vximage file for the vx1000 syst...

  • Page 27

    Vx1000 system manual version 3.3.0 27 ecu info > ecu µc displays the detected microcontroller type of the ecu connected to the selected vx device. > ecu id displays the ecu-id string defined in the vx1000 appdriver of the ecu con- nected to the selected vx device. 3.3.6 vx configuration selector con...

  • Page 28: 3.3.7 Image List View

    Vx1000 system manual version 3.3.0 28 3.3.7 image list view general information the image list view displays the vximages of the selected vx device which can be selected and flashed. List view > image this column shows the compatible images and parameters of the loaded vxcon- figurationset, vxcontai...

  • Page 30: 3.4.3 Command Bar

    Vx1000 system manual version 3.3.0 30 > insert marker inserts a text line marker showing the current time. > scan scans the network for vx devices to determine the ip address of a specific vx device. > connect opens a telnet connection to the vx device with the given ip address. > disconnect disconn...

  • Page 31

    Vx1000 system manual version 3.3.0 31 following meaning: blue text telnet status messages or markers generated by vxconsole black text standard/normal messages of the vx1000 system orange text warning messages of the vx1000 system red text error/critical messages of the vx1000 system message window.

  • Page 32: 3.5 Howto

    Vx1000 system manual version 3.3.0 32 3.5 howto the following subsections contain step-by-step installation instructions and system procedures when working with the vx1000 system. Note further details on vxconfig can be found in section vxconfig. Further details on vxconsole can be found in section ...

  • Page 33

    Vx1000 system manual version 3.3.0 33 step by step procedure please follow these steps: 1. Connect an ethernet cable to the vx device. 2. Connect this cable directly to a pc or to a network switch. 3. Connect the power supply to the connector labeled with “power”. The power led should now be on. 4. ...

  • Page 34

    Vx1000 system manual version 3.3.0 34 3.5.3.1 change ip address change ip address this procedure describes how to change the ip address of a vx device that was found during a scan with vxconfig. Step by step procedure please follow these steps: 1. Ensure that the vx device is correctly installed, co...

  • Page 35

    Vx1000 system manual version 3.3.0 35 3.5.3.2 force ip address this procedure describes how to change the ip address of a vx device that was not found during a scan with vxconfig. Caution! An unused ip address, which matches your local subnet, has to be provided by your network administrator. Step b...

  • Page 38

    Vx1000 system manual version 3.3.0 38 vxupdate procedure the vxupdate tool allows downloading of a prepared and valid vxparameter file into an available vx device. Step by step procedure please follow these steps: 1. Ensure that the vx device is connected to the pc and running. 2. Run vxupdate from ...

  • Page 39: 4 Xcp Slaves

    4 xcp slaves vx1000 system manual version 3.3.0 39 4 xcp slaves in this chapter you find the following information: 4.1 general information 40 4.2 xcp protocol parameters 40 4.3 xcp command matrix 41.

  • Page 40: 4.1 General Information

    4 xcp slaves vx1000 system manual version 3.3.0 40 4.1 general information xcp slaves the vx1000 system provides 3 xcp slaves on configurable tcp/udp ports. The config xcp slave is used to configure the vx1000 system and is used by the vx1000 system configuration tools, only. This slave is available...

  • Page 41: 4.3 Xcp Command Matrix

    4 xcp slaves vx1000 system manual version 3.3.0 41 priority threshold this is not exactly a xcp protocol parameter but rather a parameter to either reduce ethernet network load or enable low network latencies. The dtos of all daq lists bound to xcp events with a priority greater than the pri- ority ...

  • Page 42

    4 xcp slaves vx1000 system manual version 3.3.0 42 std cal daq pgm pag remark download ● download_max irrelevant for xcp on ethernet download_next irrelevant for xcp on ethernet short_download + modify_bits std cal daq pgm pag remark set_cal_page + page 0 = flash, page 1 = ram get_cal_page + std cal...

  • Page 43

    4 xcp slaves vx1000 system manual version 3.3.0 43 std cal daq pgm pag remark get_pgm_ processor_info program_prepare used for some controllers program_format + program_next irrelevant for xcp on ethernet program_max irrelevant for xcp on ethernet program_verify.

  • Page 44: Get More Information

    Get more information visit our website for: > news > products > demo software > support > training classes > addresses www.Vector.Com.