1. DL manuals
  2. Vega
  3. Modem
  4. VEGACOM 557
  5. Operating Instructions Manual

Vega VEGACOM 557 Operating Instructions Manual

Summary of VEGACOM 557

  • Page 1

    In in out out level and pressure operating instructions vegacom 557 pc/modem - interface on 557 ba pc.

  • Page 2

    2 vegacom 557 - without protocol contents safety information the described module must only be installed and operated as described in these operating instructions. Please note that other action can cause damage for which vega does not take responsibility. Note ex-area please note the approval docume...

  • Page 3

    Vegacom 557 - without protocol 3 contents 5 mounting and installation 5.1 mounting and connection instructions ............................. 12 5.2 mounting in carrier and housing ....................................... 13 6 electrical connection 6.1 connection instructions ............................

  • Page 4: 1 Product Description

    4 vegacom 557 - without protocol product description 1 product description with vegacom 557 an efficient interface converter is available. It is used for conver- sion of the vega-specific disbus and log- bus-interface to a rs232c-standard interface. Due to this, measured data and status informa- tio...

  • Page 5

    Vegacom 557 - without protocol 5 product description 1.2 functional principle the gateway vegacom 557 can be inte- grated in two ways in level or pressure meas- uring systems: - as disbus-participant - as logbus-participant. In both cases it is a passive participant. Vegacom 557 as disbus-participan...

  • Page 6: 2 Adjustment

    6 vegacom 557 - without protocol adjustment on 557 ba pc ! Voltage supply fault signal 2 adjustment the indicating elements of vegacom 557 are located in the front plate of the compo- nent. Leds are used as indicating elements signalling the operating condition (see page 9). 1.3 function the data of...

  • Page 7

    Vegacom 557 - without protocol 7 adjustment 2.2 visualisation with the visual vega (vv) visualisation program measured values of vega- processing systems can be shown graphi- cally or in tabular form. Measured value and status information are transmitted via the interface of vegacom 557 or the vegal...

  • Page 8: Communication

    8 vegacom 557 - without protocol measuring system explanation: 1 vega visual operating (vvo) adjustment software for the pc for conven- ient configuration and parameter adjust- ment of vega-instruments - vegalog 571 directly via rs 232- connection cable to cpu-card or vega- com 557 - several vegamet...

  • Page 9: 4 Technical Data

    Vegacom 557 - without protocol 9 technical data 4 technical data power supply operating voltage u nom = 24 v ac (20 … 53 v), 50/60 hz or = 24 v dc (20 … 72 v) power consumption approx. 6 va fuse 1 a, slow-blow electrical connection component multiple plug acc. To din 41 612, series f 48-pole (d, b, ...

  • Page 10

    10 vegacom 557 - without protocol technical data electrical protective measures protection: not mounted ip 00 in carrier bgt 596 or bgt log 571 - front side completely equipped ip 40 - upper and lower side bgt 596 ip 00 bgt log 571 ip 20 - wiring side ip 00 in housing type 505 - front side ip 40 - o...

  • Page 11

    Vegacom 557 - without protocol 11 162 5,5 15 100 on 557 ba 128,4 25,4 5 te technical data multipoint connector 100 x 160 x 1,5 european size multiple plug logbus- plug front rs232c interface.

  • Page 12: 5 Mounting and Installation

    12 vegacom 557 - without protocol mounting and installation d b z o 31 o o 29 o o 27 o o 25 o o 23 o o 21 o o 19 o o 15 o o 11 o o 7 o o 3 o o 1 o o 5 o o 9 o o 13 o o 17 o a c a27 c11 c3 vegalog- card interface card vegacom 557 5 mounting and installation 5.1 mounting and connection in- structions ...

  • Page 13

    Vegacom 557 - without protocol 13 mounting and installation 5.2 mounting in carrier and housing bgt 596 or bgt log 571 for mounting you just have to place a module in the requested position. A module consists of: - a multipoint connector acc. To din 41 612, series f, 33-pole (d, b, z) - two screws -...

  • Page 14: 6 Electrical Connection

    14 vegacom 557 - without protocol electrical connection 6 electrical connection 6.1 connection instructions you should please note the following instruc- tions for electrical connection: - the connection must be made according to the appropriate national installation stand- ards (e.G. In germany acc...

  • Page 15

    Vegacom 557 - without protocol 15 automatic modem-initialisation on off parameter adjustment of the interface 7 parameter adjustment of the interface component laterally basic board additional board dil-switch on basic board dil-switch basic board data format parity can be switched over from even ev...

  • Page 16: 9 Set-Up

    16 vegacom 557 - without protocol 8 vvo or vv in conjunction with vegacom 557 the configuration, parameter adjustment and adjustment of vega processing systems can be made with vega visual operating (vvo). For the visualisation of measured values the visual vega (vv) software is available. For the u...

  • Page 17: 10  Connection Examples

    Vegacom 557 - without protocol 17 connection examples 10 connection examples the following connections between pc and vegacom 557 are possible to enable ac- cess to a vega processing system from a pc with vvo or vv via a vegacom 557. • pc on the front interface • modem on the front interface 10.1 pc...

  • Page 18

    18 vegacom 557 - without protocol notes.

  • Page 19

    Vegacom 557 - without protocol 19 notes.

  • Page 20

    Iso 9001 the statements on types, application, use and operating conditions of the sensors and processing systems correspond to the actual knowl- edge at the date of printing. Technical data subject to alteration. 23290-en-021119 vega grieshaber kg am hohenstein 113 77761 schiltach/germany phone +49...