- DL manuals
- Veilux
- Security Camera
- IR PTZ VP-60IR Series
- User Manual
Veilux IR PTZ VP-60IR Series User Manual
Summary of IR PTZ VP-60IR Series
Page 1
We do future veilux ir ptz vp-60ir series user manual ver. 1.2 ptz camera 0.009º dome system accuracy / 220 call position / external firmware upgrade (rs-485) / home position & recover / slip ring for long life time / proportion ptz control the art of surveillance ®.
Page 2
Contents ptz camera contents ··················································································································································· ································· 2 components ············································································...
Page 3
Components ptz camera ptz camera bottom case camera ir led top case bubble dip switch dip switch cover accessories l-wrench - 1ea screw m4×18 - 4ea wall mount braket - 1ea set anchor bolt w5/16 - 4ea 002 the art of surveillance ® the art of surveillance ®.
Page 4
Warnings & cautions ptz camera t if you fail to read this information and handle the product incorrectly, death or serious injury may occur. T the unit should be installed by trained personnel. T switch off immediately if the product emits smoke or abnormal heat. T never install the product in an ar...
Page 5
General features ir ptz camera indoor / outdoor applications t the domes small size and construction to ip 66 ingress protection rating make it ideal for internal or external applications. 0.009º dome system accuracy with 1/16 micro step t with 0.009º technical accuracy, camera provides excellent se...
Page 6
General features ptz camera various surveillance functions t auto scan repeats pan and tilt between two call positions with different speed and dwell time. T 8 group tour up to 8 programmable group tours available and each group is consisting up to 60 calls step with different speed and dwell time w...
Page 7
Installation ir ptz camera remove the protection of cover attached each component after picking the product out from box. Remove the protection of film from top case. Take the protection of film of camera lens out from bottom case. Remove the protection of cushion from bottom case 006.
Page 8
Installation ptz camera unite both top case and bottom case using + driver. (screw locking torque : 8.0 kgf.Cm) set up the bracket which is packed with product as option on the wall. Make a decision the place for camera angle in order not to be bothered. Just double - check the wir ing hole whether ...
Page 9
Installation ir ptz camera get wiring through to the back side of wall pushing to hole inside of bracket. Unite with product using screw m4×18 from top of bracket. (screw locking torque : 10.0 kgf.Cm) make the setting over after double - check both horizon and position of product. 008.
Page 10
Quick operating keys ptz camera the dome supports pelco-d/p, samsung and vicon i3dvr(sae) protocols. The dome may be used with any controller or dvr etc that supports the pelco d and pelco p protocols. The default setting of the dome is pelco d / p (auto detection) with 2400 bps (baud rate). [pelco ...
Page 11
Quick operating keys ir ptz camera t 65+ call : "call status" is displayed, to remove this screen, press focus near button. T 70 + call : this feature provides picture stabilization image. T 92 + call : this feature freezes the current live image during tour, auto scan or pattern operation. When you...
Page 12
Diagnostic ptz camera whenever the dome is powered on, a standard diagnostic is operated. Camera id : 001 baud rate : 2400bps waiting............ Pan origin test ok tilt origin test ok tx connection test ok camera comm test ok a. Pan origin test zero point of pan is located during the panning test. ...
Page 13
Osd menu setting ptz camera to enter osd menu, press the button 95+call than osd main menu is displayed main menu dome setup camera id : cam1 home pos : off manual speed : 150º/s auto flip : off zoom speed : fast alarm : disable language : english [next page] save and exit exit [next page] system lo...
Page 14
Osd menu setting ir ptz camera a. Main menu to enter osd menu, press the button 95+call then osd main menu is displayed. Main menu dome setup camera set call auto scan tour privacy pattern alarm sector exit b. Dome set it can be possible to enter into main menu by using menu key or 95+call of contro...
Page 15
Osd menu setting ptz camera b-2. Home pos this is ability of home position, basically include recover. If you have it on, number and relevant ability would be showed up. Time is for number, relevant ability is for operation. Possible to set up the time by using left/right of joystick, if you press t...
Page 16
Osd menu setting ir ptz camera b-7. Language this is for setting the language of osd menu and basically include english / italian / polish. Change into left / right of joystick. B-8. Next page you can get into the next page by using left / right of joystick. B-9. Save and exit it can be used to save...
Page 17
Osd menu setting ptz camera t password should be inputted 2 times using number, call key. T in case of same thing with password input of 2 times, "confirmed" will be showed up and back to the menu after 4 second. T basic value of password : 99 c-3. Osd display each part can be set up into on/off, on...
Page 18
Osd menu setting ir ptz camera c-5. Initialization this is for removing the information ’s of call/tour/sector/privacy/ pattern saved in memory, on choice for load optimized default, all of value should be initialized to factory default. Initialization [tour clear] [call clear] [sector clear] [priva...
Page 19
Osd menu setting ptz camera t camera set menu #1 camera set shutter full auto mirror off aperture 16 d zoom off wb mode atw mode blc off[blc] d/n mode auto mode [slow] [next page] exit t camera set menu #2 [next page] d-1. Shutter camera set sense up x2 agc mode middle ssnr mode middle color 050 dis...
Page 20
Osd menu setting ir ptz camera d-2. Mirror possible to set up on/off, image should be left side to right. D-3. Aperture sharpness can be controlled. - the value for default is 16, possible to adjust 00~31, higher the number, clear the sharpness. D-4. D zoom digital zoom can be set on/off. D-5. Wb mo...
Page 21
Osd menu setting ptz camera d-6-2. Hlc mode (high light compensation) blc set blc mode hlc level set high mask color 07 exit t level set : possible to set up into high/low. T mask color : higher the number, closer to black and feasible to set up 01~16 d-6-3. Ssdr mode (samsung super dynamic range) b...
Page 22
Osd menu setting ir ptz camera d-8. Sense up you can set up the digital slow shutter, not doing anything directly. In case on on sense up, shutter speed should be adjusted according to amount of lights. Then slow shutter is not working that the section set to sense up would be limited. - possible to...
Page 23
Osd menu setting ptz camera e. Call set you can insert to call menu using left/right of joystick after choice call set. Call set call no : 001 call id : call001 pan : 123.2 tilt : 89.2 freeze mode : off freeze all : off save exit e-1. Call no. Possible to set up the number of call to save using left...
Page 24
Osd menu setting ir ptz camera e-3. Pan/tilt if you press the focus far key after place cursor to menu, sign would be showed up on the left and can set up the position, zoom you want. And then get out of there pressing the focus far key after completing setting. That time, should be taken out. E-4. ...
Page 25
Osd menu setting ptz camera f-1. Start / end angle possible to set up the position of beginning and end of auto scan. - you can control the only position of pan from each menu of start angle/ end angle in basic screen. - in case you change the position of tilt or zoom, it'd be possible only with sta...
Page 26
Osd menu setting ir ptz camera g. Tour you can use this function using left/right of joystick after choice the tour in the main menu. Tour set tour no. : 01 tour title : tour01 tour step : 01 call no. : 001 dwell time : 03 speed : 300º/s save exit g-1. Tour no. This is for menu for choice the group ...
Page 27
Osd menu setting ptz camera g-6. Speed possible to set up the time moving to relevant call. - the v alue for setting is 10º/s~400º/s, can input it direc tly using [1-40]+call. (on inserting direct, you should input the value of shared into 10 from relevant speed value.) f-3. Tour step this is for tu...
Page 28
Osd menu setting ir ptz camera h-3. Action this is for set up the position, size of privacy mask, you can control with 2 adjust mode in order to set the move mode and size for set the position. - possible for setting move/adjust using left/right of joystick in action menu. » move : you can adjust th...
Page 29
Osd menu setting ptz camera i-2. Patt title on working pattern, the function for inputting the characters for title if showed up on the screen. - default is for "pattern01 " - the changing of character can be set up using the left/right/up or zoom in/out of joystick. I-3. Data fill this is for marki...
Page 30
Osd menu setting ir ptz camera j-2. Alarm input set up the sensing way of alarm or using ararm. - [off/no/nc] can be set up. - no's meaning is normal open and handle the close to normal of open. - nc's meaning is normal close and handle the open to normal of close. - it should be controlled by using...
Page 31
Osd menu setting ptz camera k. Sector this is for sign the title on the screen on sprecial section to get in using left/ right of joystick after choose the sector in the main menu. Sector set sector no. : 01 sector id : sector1 sector start : 334.7 -1.6 sectpr emd : 000.4 08.8 save exit k-1. Sector ...
Page 32
Dip switch setting ptz camera a. Id setting the camera has camera id to be controlled by controller or dvr. After opening, set id using dip sw1. T factory default : camera id = 1 id sw1-#1 sw1-#2 sw1-#3 sw1-#4 sw1-#5 sw1-#6 sw1-#7 sw1-#8 1 on off off off off off off off 2 off on off off off off off ...
Page 33
Dip switch setting ptz camera id sw1-#1 sw1-#2 sw1-#3 sw1-#4 sw1-#5 sw1-#6 sw1-#7 sw1-#8 35 on on off off off on off off 36 off off on off off on off off 37 on off on off off on off off 38 off on on off off on off off 39 on on on off off on off off 40 off off off on off on off off 41 on off off on o...
Page 34
Dip switch setting ptz camera id sw1-#1 sw1-#2 sw1-#3 sw1-#4 sw1-#5 sw1-#6 sw1-#7 sw1-#8 81 on off off off on off on off 82 off on off off on off on off 83 on on off off on off on off 84 off off on off on off on off 85 on off on off on off on off 86 off on on off on off on off 87 on on on off on off...
Page 35
Dip switch setting ptz camera id sw1-#1 sw1-#2 sw1-#3 sw1-#4 sw1-#5 sw1-#6 sw1-#7 sw1-#8 127 on on on on on on on off 128 off off off off off off off on 129 on off off off off off off on 130 off on off off off off off on 131 on on off off off off off on 132 off off on off off off off on 133 on off o...
Page 36
Dip switch setting ptz camera id sw1-#1 sw1-#2 sw1-#3 sw1-#4 sw1-#5 sw1-#6 sw1-#7 sw1-#8 173 on off on on off on off on 174 off on on on off on off on 175 on on on on off on off on 176 off off off off on on off on 177 on off off off on on off on 178 off on off off on on off on 179 on on off off on o...
Page 37
Dip switch setting ptz camera id sw1-#1 sw1-#2 sw1-#3 sw1-#4 sw1-#5 sw1-#6 sw1-#7 sw1-#8 219 on on off on on off on on 220 off off on on on off on on 221 on off on on on off on on 222 off on on on on off on on 223 on on on on on off on on 224 off off off off off on on on 225 on off off off off on on...
Page 38
Dip switch setting ptz camera dip s/w no. Definition detail 1 binary number protocol #1 321 : dip s/w number 000 : pelco-d/p 001 : vicon 010 : samsung 011 : sae 100 : x 101 : x 110 : x 111 : x 2 binary number protocol #2 3 binary number protocol #3 4 binary number baud rate #1 54 : dip s/w number 00...
Page 39
Trouble shooting ptz camera if you have trouble operating in your camera, refer to the following. No operating t check if the power supply is ac24v t check if rs-485 communication cable is connected correctly. T check camera id setting. T check the termination. No picture t check if all the cables a...
Page 40
Specification (with ir) ptz camera model vp-ir6027x vp-ir6033x vp-ir6037x vp-ir3036x pan/tilt pan rotation angle 360º endless pan speed manual : 0.5º ~ 200º /sec (64step) / call : max 400º/sec tilt rotation angle -2º ~ 90º tilt speed manual : 0.5º ~ 150º/sec (64step) / call : max 350º/sec system acc...
Page 41
40. 9 144. 3 217. 9 129.4 03.0 040