1. DL manuals
  2. Velleman
  3. Car Alarm
  4. K3511
  5. Illustrated Assembly Manual

Velleman K3511 Illustrated Assembly Manual

Other manuals for K3511: User Manual
Manual is about: Remote controlled

Summary of K3511

  • Page 1

    Total solder points: 88 + 68 + 367 difficulty level: beginner 1 2 3 4 5 ⌧ advanced remote controlled car alarm illustrated assembly manual h3511ip-2 k3511 k3511.

  • Page 2

    2 features : microprocessor technology. Multi-functional remote control operation. Audio and visual on/off indicators. Multifunction dashboard mounted led. Automatic reset after alarm. Adjustable voltage drop (reaction to interior lighting). Voltage drop detection active immediately, or after 5 minu...

  • Page 3

    3 assembly hints 1. Assembly (skipping this can lead to troubles ! ) ok, so we have your attention. These hints will help you to make this project successful. Read them carefully. 1.1 make sure you have the right tools: • a good quality soldering iron (25-40w) with a small tip. • wipe it often on a ...

  • Page 4

    4 1.3 soldering hints : 1- mount the component against the pcb surface and carefully solder the leads 2- make sure the solder joints are cone-shaped and shiny 3- trim excess leads as close as possible to the solder joint remove them from the tape one at a time ! Axial components are taped in the cor...

  • Page 5

    5 before mounting the components to the pcb it must first be checked that the pcb fits in the housing. Be careful of the small notch next to ld1. Should it not fit the edge of the pcb can be sanded down with fine sandpaper. The car alarm consist of three pcb’s, 1 for the remote control transmitter, ...

  • Page 6

    6 ld1 : 3mm red 11. Led (check the polarity) cv : 1,5 - 5pf 7. Capacitive trimmer cv... Ic1 : 18p 8. Ic socket (watch the position of the notch) ic... 1 c1 : 2pf (2,2) c2 : 2pf (2,2) c3 : 330pf (331) 9. Capacitors c... T1 : bf199 10. Transistor 7mm 11mm + - 12. Led (check the polarity) ic1 : um3758 ...

  • Page 7

    7 the code can be set for a transmitter/receiver combination. There is a row of 9 coding islands for setting the code. The closest is near the ic legs. The code can be set by connecting one or more of these coding islands to a neighbouring - island or a neighbouring + island using a jumper, or by no...

  • Page 8

    8 (b) construction of the remote control receiver p3511r zd1 : 4v3 zd2 : 5v1 zd3 : 5v1 1. Zener diode (check the polarity) cathode zd... R1 : 270 (2 - 7 - 1 - b) r2 : 2k2 (2 - 2 - 2 - b) r3 : 18k (1 - 8 - 3 - b) r4 : 18k (1 - 8 - 3 - b) r5 : 33k (3 - 3 - 3 - b) r6 : 5k6 (5 - 6 - 2 - b) r7 : 2k7 (2 -...

  • Page 9

    9 solder side fig.8 cv1 : 5pf 8. Capacitive trimmer cv... Solder side ld1 : 3mm red 9. Led (check the polarity) 8mm ic1 : rv4558, lm258, lm2904 10. Ic (watch the position of the notch !) construction.

  • Page 10

    10 (c) construction of the main pcb 3511 j 1. Jumperwire zd1 : 2v4 zd2 : 5v1 zd3 : 18v zd4 : 18v zd5 : 18v 3. Zener diode. Check the polarity! D1 : 1n4148 d2 : 1n4148 d3 : 1n4148 d4 : 1n4148 d5 : 1n4148 d6 : 1n4148 d7 : 1n4000 … 1n4007 d8 : 1n4000 … 1n4007 d9 : 1n4000 … 1n4007 d10 : 1n4000 … 1n4007 ...

  • Page 11

    11 l1 : 100µh (1 - 0 - 1 - a) 5. Axial coil l2 ic1 : 8p ic2 : 18p ic3 : 18p 6. Ic sockets (watch the position of the notch) ic... 1 l... Rv1 : 4k7 / 5k 7. Potentiometer rv1 ld1 : 3mm red 8. Led (check the polarity) ld1 cathode c1 : 100pf (101) c2 : 330pf (331) c3 : 100nf (µ1 - 104) c4 : 100nf (µ1 - ...

  • Page 12

    12 13. Pin contacts 18mm cut c11 : 1µf c12 : 1µf c13 : 1µf c14 : 1µf c15 : 1µf c17 : 1µf c18 : 1µf c19 : 22µf c20 : 220µ f c21 : 1000µf 14. Electrolytic capacitors. Watch the polarity ! C... D13 : 6a2, 6a6 or eq. D14 : 6a2, 6a6 or eq. 15. Diodes (check the polarity) cathode d... Jp1 : 3p jp2 : 3p jp...

  • Page 13

    13 mount the receiver pcb “p3511r” on the main pcb “p3511” using the 20mm treaded rod. Check that the components of the main pcb and the receiver pcb do not touch each other. 21. Final assembly see point 15 in transmitter construction “p6706”. (pag. 7) 20. Create your code important: • to tune the r...

  • Page 14

    14 23. Pcb p6706 pcb 24. Pcb p3511r.

  • Page 15

    15 25. Main pcb p3511 pcb.

  • Page 16

    16 26. Diagram remote transmitter diagram d1 4 b attery 12v - + a11 a12 sw1 sw2 d2 um3758-120a nc a10 10 a9 a8 9 8 a6 a7 7 6 a5 5 17 14 12 11 vss tx 13 ic1 osc a4 a3 3 a2 a1 2 1 mode vdd 16 18 15 rx nc r1 l2 c1 t1 r3 r2 c3 c2 r4 cv ld1 r5 zd1 l1.

  • Page 17

    17 27. Diagram remote receiver r9 a1 l2 r5 r6 l1 c1 r7 t1 c5 a1,a2 = ic1 c4 r4 cv1 r3 c3 r1 r8 c6 c7 r2 a2 gnd rx out zd2 zd1 r13 zd3 ld1 +9v r11 3 1 2 c2 r10 5 6 4 8 7 r12 diagram.

  • Page 18

    18 28. Main diagram diagram warning out direction lights vdd c9 d11 ry2 ra0 rtcc +v +v3 r28 r22 d4 t3 codelock r29 r40 r24 +v codelock in fan sens in c8 r26 d6 c18 r8 r25 r34 d5 r15 +v3 c17 t2 +v r16 r14 contact1 contact2 warning sensors in direct sensors in c14 d10 t12 ry1 d9 zd3 d8 c15 zd2 r32 d2 ...

  • Page 19

    19.

  • Page 20

    20 velleman kit nv legen heirweg 33 9890 gavere belgium europe info ?: http://www.Velleman.Be modifications and typographical errors reserved © velleman kit nv h3511ip - 2003 - ed2 5 4 1 0 3 2 9 2 9 1 5 1 8.