Summary of K4700
Page 1
Speaker protection kit k4700 illustrated assembly manual h4700ip-1 total solder points: 163 difficulty level: beginner 1 2 3 4 5 advanced protect s your preciou s speak ers aga inst switch- on click s and d c curre nt..
Page 3
3 features this stereo loudspeaker protection will protect the loudspeakers against the switch-impulsions and the direct current component on the output of the connected amplifier. Suitable for: * amplifiers with symmetrical power supply * amplifiers with asymmetrical power supply. Specifications : ...
Page 4
4 assembly hints 1. Assembly (skipping this can lead to troubles ! ) ok, so we have your attention. These hints will help you to make this project successful. Read them carefully. 1.1 make sure you have the right tools: • a good quality soldering iron (25-40w) with a small tip. • wipe it often on a ...
Page 5
5 assembly hints 1.3 soldering hints : 1- mount the component against the pcb surface and carefully solder the leads 2- make sure the solder joints are cone-shaped and shiny 3- trim excess leads as close as possible to the solder joint remove them from the tape one at a time ! Axial components are t...
Page 6
6 r1 : 3k3 (3 - 3 - 2 - b) r2 : 3k3 (3 - 3 - 2 - b) r3 : 8k2 (8 - 2 - 2 - b) r4 : 8k2 (8 - 2 - 2 - b) r5 : 8k2 (8 - 2 - 2 - b) r6 : 8k2 (8 - 2 - 2 - b) r7 : 8k2 (8 - 2 - 2 - b) 4. Resistor r... Construction d1 : 1n4148 d2 : 1n4148 d3 : 1n4148 d4 : 1n4148 d5 : 1n4148 d6 : 1n4148 d7 : 1n4148 d8 : 1n41...
Page 7
7 mains (n - l) +v man -v gnd pa ls pa ls 8. Pcb tabs. Construction ic1 : 14p t1 : bc547b t2 : bc547b t3 : bc547b t4 : bc517 7. Transistors left right 6. Ic socket, watch the position of the notch ! Ld1 cathode ld1 : red (error) ld2 : yellow (wait) 9. Leds. Watch the polarity! C1 : 1µ f c2 : 1µ f c3...
Page 8
8 construction ry1 : vr15m121c (12vdc - 15a - 1c) ry2 : vr15m121c (12vdc - 15a - 1c) cover the wide connecting broad leads with solder. 12. Relays ry... Transfo (1,2va - 2 x 6v / 2 x 0,1a) 13. Transformer transformer 6 0 6 n l ic1 : lm324 14. Ic. Watch the position of the notch! Check the entire mod...
Page 9
9 testing connect a net-cord to the mains, connect the module to the net and check if after approx.+/-6 sec. The yellow led 'wait' extinguishes; at the very same moment the led is extinguishing, one should hear the clack of the relais switching. Testing the left channel : connect the point pa of the...
Page 10
10 testing the right channel : connect the point pa of the right channel to the point -v (figure 3.0); the red led 'error' should now be lightening together with the yellow led 'wait'. When the connection is interrupted again (figure 4.0), the red led should extinguish and after approx. +/- 6 sec. T...
Page 11
11 first find a proper place to install the protection module (f.I. Against the back-side of the housing). Realise the following connections: mains: this connection has to be linked to the net-connection of the transformer in the amplifier, i.E. After the net-switch! Pa: connect this point to the sp...
Page 12
12 fig. 5.0 on/off input right mains output right output left input left power supply pa ls pa ls left right mains p4700 stereo power amplifier on/off input mains output + output - power supply pa ls pa ls left right mains p4700 bridge power amplifier fig. 6.0 connection.
Page 13
13 17. Pcb layout. Pcb.
Page 14
14 diagram 18. Diagram.
Page 16
Modifications and typographical errors reserved © velleman components nv. H4700ip - 2004 - ed1 (rev 1.0) velleman components nv legen heirweg 33 9890 gavere belgium europe www.Velleman.Be www.Velleman-kit.Com 5 4 1 0 3 2 9 3 1 0 1 6 5.