1. DL manuals
  2. Velleman
  3. Battery Charger
  4. K8019
  5. Manual

Velleman K8019 Manual

Manual is about: PROXIMITY CARDREADER WITH USB INTERFACE

Summary of K8019

  • Page 1

    Illustrated assembly manual h8019ip’1 illu llu llu llu l illu stra stra stra ra ra ted ted ted t d d ted ted as ass ass asse asse asse as as e mbly mbly mbly bly bly ly y y m m m ma man man ual ual ual al al h801 h801 h801 1 1 h80 9ip’ 9ip 9ip’ 9ip’ p 9 9ip’ 9 9ip 1 1 1 k8019 k8019 proximity card pr...

  • Page 2

    Forum forum participate our velleman projects forum subscribing our newsletter?, visit www.Vellemanprojects.Eu.

  • Page 3: Velleman N.V.

    Velleman n.V. Legen heirweg 33 9890 gavere (belgië).

  • Page 4

    Assembly hints 1. Assembly (skipping this can lead to troubles ! ) ok, so we have your attention. These hints will help you to make this project successful. Read them carefully. 1.1 make sure you have the right tools: • a good quality soldering iron (25-40w) with a small tip. • wipe it often on a we...

  • Page 5

    - 5 - do not blindly follow the order of the components onto the tape. Always check their value on the parts list!.

  • Page 6

    - 6 -  r1: 470 (4 - 7 - 1 - b)  r2: 470 (4 - 7 - 1 - b)  r3: 470 (4 - 7 - 1 - b)  r4: 100k (1 - 0 - 4 - b)  r5: 100k (1 - 0 - 4 - b)  r6: 10k (1 - 0 - 3 - b)  r7: 10k (1 - 0 - 3 - b)  r8: 10k (1 - 0 - 3 - b)  r9: 220k (2 - 2 - 4 - b)  r10: 220k (2 - 2 - 4 - b)  r11: 4k7 (4 - 7 - 2 - b)  ...

  • Page 7

    - 7 - 7 ceramic capacitors  c1: 10nf (103)  c2: 10nf (103)  c3: 10nf (103)  c4: 4.7nf (472)  c5: 4.7nf (472)  c6: 4.7nf (472)  c12: 100pf (101)  c13: 100pf (101)  c14: 470pf (471)  c16: 22pf (22)  c17: 22pf (22)  c18: 470nf (474) c... 8 transistors 9 buzzer 10 terminal block 13 electroly...

  • Page 8

    - 8 - 16 voltage regulator 1 led’s. Watch the polarity!  vr1: ua7805 17 relay 18 ic’s  ry1: vr15121c watch the position watch the position of the notch! Of the notch!  ic1: lm358  ic2: vk8019 (programmed pic18f14k50-i/p) rfid reader pcb r bend the leads bend the leads  ld1 (red)  ld2 (blue)  ...

  • Page 9

    - 9 - 2 board to wire (female) connect to main board construction.

  • Page 10

    - 10 - assembly ii m3 nut m3 x 25mm allen screw spacer m3 nut assembly.

  • Page 11: III

    - 11 - hook-up example iii hook-up example.

  • Page 12: IV. Software Installation

    - 12 - iv. Software installation step 1: download the software on our website. Step 2: open the fi le en select the software. Step 3: select “next” to begin the installation. Step 4: select the destination on your pc. Step 5: select the “start folder” menu where program shortcuts should be placed. R...

  • Page 13: V. Driver

    - 13 - step 6: select additional tasks you would like to be performed. Step 7: select “install” for installing the software. Step 8 : click “fi nish” to exit setup. V. Driver installation connect the usb connector of the k8019 to your pc using an usb cable. With the fi rst connection, you should ins...

  • Page 14: VI. Indications

    - 14 - vi. Indications the card reader has three colored leds: green, blue and red. A. Leds b. Sound enter / leave learn mode valid card / card stored (learning mode) ld3 ld2 ld1 led status ld1 on relay off ld2 on power on blinking learning mode enabled ld3 on relay energized invalid card indication...

  • Page 15: Vii. Set-Up

    - 15 - vii. Set-up learning mode relay when a valid card is presented the relay is energized. The relay has three confi gurations (the confi guration is done via the pc): • toggle: swipe= on, swipe= off. • momentary: on while card is present. • timer/delayed: swipe= on for n seconds. Learning mode o...

  • Page 16

    - 16 - an rfid tag sleeps in normal mode: it does not perform any activities and does not use any power. This will change as soon as the tag moves through the reader’s fi eld. An rfid reader emits radio waves at a frequency similar to those of the tag. The tag antenna retrieves enough energy from th...

  • Page 17

    - 17 - d1 1n4148 d2 1n4148 d3 1n4148 c1 10n r1 470 r4 100k gnd c4 4n7 c7 100n r6 10k c5 4n7 r2 470 r7 10k 3 2 8 4 1 ic1a lm358 5 6 7 ic1b lm358 c12 100p r9 220k r10 220k r3 470 c2 10n c8 100n gnd r14 39k c6 4n7 gnd r11 4k7 r15 1m r5 100k c13 100p r8 10k r16 10 t1 bc547 t4 bc557 gnd r17 330 c14 470p ...

  • Page 18

    - 18 - pcb.

  • Page 19

    Supply voltage (v) - led voltage (v) required current (a) = series resistance (ohms) required current (a) = series resistance (ohms) required resistor power handling= voltage over resistor x current passed trough resistor 9v - 1.7v 0.005a = 1460 ohm 9v - (3 x1.7v) 0.005a = 780 ohm (9v - 1.7v) x 0.00...

  • Page 20

    The new velleman projects catalogue is now available. Download your copy here: www.Vellemanprojects.Eu modifi cations and typographical errors reserved - © velleman nv. H8019ip’1 (rev.1) velleman nv, legen heirweg 33 - 9890 gavere..