K8048 illustrated assembly manual h8048ip-1 total solder points: 274 difficulty level: beginner 1 2 3 4 5 advanced pic® programmer and experiment board suitable for programm ing microch ip ® flash pic tm microcontro llers. Basic prog ramming k nowledge is required specifications suitable for program...
Fr vous trouverez la traduction de cette notice sur le cd, avec d'autres informations nl vertaling van deze handleiding, als ook meer gegevens kan men terugvinden op de cd. Uk the translation of this manual and all other information can be found on the cd. D dieübersetzung dieser anleitung und alle ...
3 features: suitable for programming microchip® flash pic(tm) microcontrollers supports 4 different 300 mil. Pics: 8p, 14p, 18p and 28p test buttons and led indicators to carry out educational experiments, such as the enclosed programming examples easy connection to a pc through the serial port encl...
4 assembly hints 1. Assembly (skipping this can lead to troubles ! ) ok, so we have your attention. These hints will help you to make this project successful. Read them carefully. 1.1 make sure you have the right tools: • a good quality soldering iron (25-40w) with a small tip. • wipe it often on a ...
5 assembly hints 1.3 soldering hints : 1- mount the component against the pcb surface and carefully solder the leads 2- make sure the solder joints are cone-shaped and shiny 3- trim excess leads as close as possible to the solder joint remove them from the tape one at a time ! Do not blindly follow ...
6 r1 : 15k (1 - 5 - 3 - b) r2 : 220k (2 - 2 - 4 - b) r3 : 4k7 (4 - 7 - 2 - b) r4 : 1k (1 - 0 - 2 - b) r5 : 15k (1 - 5 - 3 - b) r6 : 220k (2 - 2 - 4 - b) r7 : 4k7 (4 - 7 - 2 - b) r8 : 1k (1 - 0 - 2 - b) r9 : 4k7 (4 - 7 - 2 - b) r10 : 3k3 (3 - 3 - 2 - b) r11 : 4k7 (4 - 7 - 2 - b) r12 : 330 (3 - 3 - 1 ...
7 t1 : bc547 t2 : bc547 t3 : bc557 t4 : bc547 t5 : bc547 construction 8. Transistors. Ic1 : 8p ic2 : 14p ic3 : 18p ic4 : 28p 6. Ic sockets, watch the position of the notch! Ld1 : 3mm ld2 : 3mm ld3 : 3mm ld4 : 3mm red ld5: 3mm ld6 : 3mm ld8 : 3mm ld7 : 3mm green 7. Leds. Watch the polarity ! Color= 2...
8 sk3 : 5p c1 : 220µf 15. Electrolytic capacitor. Watch the polarity ! C... Construction ld9 : blinking red (5mm) ld1 cathode 11. Blinking led. Watch the polarity! Sk1 : 15vdc (power) 12. Dc - jack sk2 : rs232 (9p female) 13. Sub d - connector x1 : 4mhz x... 14. Quartz crystal sw5 : 3 pos. / 2 pole ...
9 mount the rubber feet on the solder side of the pcb, see fig 1.0. 17. Rubber feet construction • place the velleman® software cd in your cd-rom player. • select ‘browse through this cd for other velleman software’ (this message will not be displayed on your screen if ‘autorun’ is not activated. • ...
10 20. Schematic diagram. Schematic diagram.
11 pcb 21. Pcb.
5 4 1 0 3 2 9 2 9 1 9 5 2 modifications and typographical errors reserved - © velleman nv. H8048ip - 2004 - ed1 (rev. 5.0).
