2 channel rf codelock transmitter k8059 illustrated assembly manual h8059ip-1 total solder points: 63 difficulty level: beginner 1 2 3 4 5 advanced for use with k8 057/vm 109 2 chan nel rf receive r.
3 features: for use with the k8057/vm109 2-channel rf receivers. Generates unique 32-bit code. More than 1,000,000,000 unique codes. Code can easily be changed for safety purposes. Choose continuous or 'burst' transmission. Led indicator. Limited compatibility with k6706 - k6706a - k6706b/g specific...
4 assembly hints 1. Assembly (skipping this can lead to troubles ! ) ok, so we have your attention. These hints will help you to make this project successful. Read them carefully. 1.1 make sure you have the right tools: • a good quality soldering iron (25-40w) with a small tip. • wipe it often on a ...
5 assembly hints 1.3 soldering hints : 1- mount the component against the pcb surface and carefully solder the leads 2- make sure the solderjoints are cone-shaped and shiny 3- trim excess leads as close as possible to the solder joint remove them from the tape one at a time ! Axial components are ta...
6 construction sw1 : krs0611 sw2 : krs0611 sw3 : krs0611 5. Push buttons x1 : saw433 4. Saw resonator x... D1 : bat85 d2 : bat85 1. Diodes. Watch the polarity! D... Cathode zd1 : 5v1 / 500mw 2. Zenerdiode. Watch the polarity! Zd... Cathode r1 : 33k (3 - 3 - 3 - b) r2 : 33k (3 - 3 - 3 - b) r3 : 33k (...
7 construction t1 : mpsh10 10. Transistor + - check for good attachment of the solder to the contacts 7. Battery contacts c1 : 1pf (1) c2 : 4p7 (4.7) c3 : 100pf (101) bend c3 away from the led c4 : 100pf (101) c5 : 100pf (101) c6 : 100nf (104) 9. Capacitors ic1 : vk8059 vk8059=(programmed pic12f629)...
8 the transmitter comes with a factory set default code. However, for security reasons, it might be wise not to use the default code. 1. To program your unique code : hold sw1(*) (left button). Briefly press the 'program'-button (sw3) 3 times. The led will flash 3 times. Release sw1. Your unique 32-...
9 3. Compatibility with previous transmitters (k6706 - k6706a - k6706b - k6706g) : 3 different codes can be generated, solder a bridge as indicated below. Modify excisting transmitters and receivers : - + - + - + um3758 no code um3758 pin1with - um3758 pin1with + new old.
10 14. Schematic diagram. Schematic diagram c3 100p c1 1p c2 4p7 t1 mpsh10 r5 220-1/8w r4 47-1/8w ld1 led3rl x1 saw433 r1 33k-1/8w c4 100p sw1 sw krs0611 sw2 sw krs0611 gp4/t1g/osc2/clkout 3 vdd 1 gp5/t1cki/osc1/clkin 2 gp3/mclr/vpp 4 gp2/t0ckl/int/cout 5 gp0/cin+/icspdat 7 gp1/cin-/icspclk 6 vss 8 ...
11 pcb 15. Pcb.
Modifications and typographical errors reserved © velleman components nv. H8059ip - 2004 - ed1 (rev. 1.0) velleman components nv legen heirweg 33 9890 gavere belgium europe www.Velleman.Be www.Velleman-kit.Com 5 4 1 0 3 2 9 3 1 2 0 7 7.
