1. DL manuals
  2. Velodyne
  3. Wireless Router
  4. WiConnect System
  5. Manual

Velodyne WiConnect System Manual - Enjoy.

Other manuals for WiConnect System: Specification, User Manual, User Manual

Summary of WiConnect System

  • Page 1

    Set up u s e r ’ s m a n u a l wiconnect wireless subwoofer.

  • Page 2: Enjoy.

    Enjoy. We here at velodyne want to thank you for selecting our product. Get ready to experience the highest quality and amazing low-distortion bass that velodyne is world famous for. Relax as you enhance your home entertainment experience with our easy setup instructions. Welcome . . . Enjoy your ne...

  • Page 3

    S a f e t y n o t i c e s e t u p place subwoofer subwoofer placement guidelines subwoofer placement cautions box contents connect wireless transmitter to receiver select receiver options optimal subwoofer performance connect subwoofer select wireless broadcast channel — wireless broadcast considera...

  • Page 4

    Safety notice caution: to reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer servicing to qualified service personnel. The lightning flash with arrowhead symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” wit...

  • Page 5

    12. Power-cord protection — power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point at which they exit from the product. 13. Cleaning — the p...

  • Page 6

    Set up place subwoofer [ 3 ] w iconnect user’s manual set up.

  • Page 7

    The seating positions shown in the diagram above are general guidelines for most room types and aren’t dependent on the subwoofer placement. Sitting closer to the front in a “boomy bass” room may sound better. Sitting closer to the back of a “bass shy” room may sound better. Subwoofer placement guid...

  • Page 8

    Box contents now that you’ve unpacked the subwoofer, make sure you have the components and velodyne supplied accessories shown below. Also, acquire the necessary user supplied accessories. If any components or velodyne supplied accessories are missing or damaged, contact the retailer where you purch...

  • Page 9

    Subwoofer cabinet back [ 6 ] w iconnect user’s manual set up a. Channel: select broadcast frequency. This channel selection must match channel selection on the transmitter. B. Lfe input: optional wired connection to receiver, if not using the wireless connection. C. Phase: invert the phase of the su...

  • Page 10

    Connect wireless transmitter to receiver use one of the following two setups to connect the wireless transmitter to receiver: setup #1: most common (receiver has lfe/sub output) [ 7 ] w iconnect user’s manual set up setup #1: most common (receiver lfe/sub output) this setup requires one rca cable. S...

  • Page 11

    Setup #2: less common (receiver has no lfe/sub output) [ 8 ] w iconnect user’s manual set up 1. Use the two rca cables supplied by you to connect the wireless transmitter’s r and l inputs to your receiver’s r and l outputs. 2. Plug the wireless transmitter’s 5v dc power adaptor into the back of the ...

  • Page 12

    Select receiver options optimal subwoofer performance it is important that the audio system’s existing receiver is set up correctly to work in concert with the subwoofer. To set up the receiver refer to its instruction manual and use one of the following three options: r e c e i v e r o p t i o n s ...

  • Page 13

    Connect subwoofer 1. Use the included power cord to connect the subwoofer to a power outlet. 2. Turn the power switch to the on position. The active light should be yellow. After 12 minutes without receiving a signal, the active light turns red to indicate stand by mode. The subwoofer will automatic...

  • Page 14

    Adjust subwoofer controls for listening preferences now it’s time to adjust the subwoofer controls to match your listening environment and preferences. 1. Play some music through your receiver. 2. Turn the subwoofer’s volume to a level that balances with the output volume of your satellite speakers ...

  • Page 15

    Connect multiple wireless subwoofers in a single audio system if you are using more than one wireless subwoofer in a single audio system, the following two setup options exist. Option #1 : all subwoofers receive the same audio signal. This is the most common setup. For this setup: 1. Connect only on...

  • Page 16

    Use the subwoofer’s lfe input (optional) in case you misplace the wireless transmitter or the wireless transmitter malfunctions, you can also connect the subwoofer to your receiver with an rca cable. [ 13 ] w iconnect user’s manual set up 1. Use the rca cable, supplied by you, to connect one end of ...

  • Page 17

    Mount wireless transmitter on wall (optional) optionally, you can mount the wireless transmitter on the wall or place in a location that better organizes your audio components. The transmitter doesn’t have to be visually in view in the room to function properly wireless transmitter mounting template...

  • Page 18

    Maintain protect subwoofer from damage do not put heavy objects on top of the subwoofer cabinet or wireless transmitter that could scratch or dent the cabinet or case. Do not allow objects to fall into or liquids to spill on the subwoofer enclosure. Do not expose subwoofer to dripping or splashing f...

  • Page 19

    Troubleshoot if the subwoofer’s active light isn’t yellow or red: 1. Verify that the subwoofer is plugged into a live power outlet. 2. Verify that the subwoofer’s power switch is in the on position. 3. Verify that the power cord is not damaged. If damaged, replace the cord. If the subwoofer isn’t pr...

  • Page 20

    Resources specifications model wic-10 woofer 10” downward firing (7.65” piston diameter) amplifier (class d) 200 watts dynamic, 125 watts rms power magnet structure 2 lbs. (0.9 kg) frequency response 33 hz – 140 hz (+/- 3 db) voice coil 1.6” copper wound cone coated fiber speaker-level pass-through ...

  • Page 21

    [ 19 ] w iconnect user’s manual resources regulatory information fcc compliance statement this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference recei...

  • Page 22

    [ 20 ] w iconnect user’s manual warranty for your records. . . Date purchased _____________________________________________________________________________________ dealer ______________________________________________________________________________________________ serial # _________________________...

  • Page 23

    Velodyne acoustics, inc. 345 digital drive morgan hill, ca 95037 408.465.2800 voice 408.779.9227 fax 408.779.9208 service fax www.Velodyne.Com service e-mail: service@velodyne.Com general e-mail: help@velodyne.Com 63-wic-10 rev b oct10