- DL manuals
- Venmar
- Ventilation Hood
- VBLDF1
- Installation Use And Care Manual
Venmar VBLDF1 Installation Use And Care Manual
Summary of VBLDF1
Page 1
Www.Venmar.Ca serial number: 99045653-002a range hood series: vbldf1 and vblsh1 installation, use and care manual.
Page 2: Table of Contents
Inst alla tion manual table of contents 2 safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 cleaning and maintenance . . . . . . . . . . . . . . . . . 6 motor grease filter non-ducted recirculation f...
Page 3: Safety
Inst alla tion manual safety 3 read and save these instructions ! Intended for domestic cooking only ! Installer: leave this manual with homeowner. Register your range hood online at www.Venmar.Ca ! Warning to reduce the risk of fire, electric shock, or injury to persons, observe the following: • us...
Page 4: Safety
Inst alla tion manual safety 4 ! Warning to reduce the risk of a range top grease fire: a) never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. B) always turn hood on when cooking at high hea...
Page 5: Opera
Inst alla tion manual opera tion 5 operation always turn your hood on before you begin cooking to establish an air flow in the kitchen. Let the blower run for a few minutes to clear the air after you turn off the range. This will help keep the whole kitchen cleaner and fresher. Operate the hood as f...
Page 6: Cleaning and Maintenance
Inst alla tion manual cleaning and maintenance 6 cleaning and maintenance proper maintenance of the range hood will assure proper performance of the unit. Motor the motor is permanently lubricated and never needs oiling. If the motor bearings make excessive or unusual noise, replace the motor with t...
Page 7: Inst
Inst alla tion manual inst alla tion 7 recommended tools and accessories for installation • measuring tape • phillips screwdriver no. 2 • flat blade screwdriver (to open knockout holes) • drill, 1/8” drill bit and 1½” hole saw (to mark holes for ducting and cut electrical access hole) • 7/64” drill ...
Page 8: Inst
Inst alla tion manual inst alla tion 8 contents before proceeding to the installation, check the contents of the box. If items are missing or damaged, contact the manufacturer. Make sure that the following items are included: vbldf1 series vblsh1 series (2) g rease f ilters (1) 3¼” x 10” d amper ass...
Page 9: Inst
Inst alla tion manual inst alla tion 9 prepare the hood 1 ] if present, remove all protective polyfilm from the hood and/or parts. 2 ] using the finger cup, remove the grease filters from the hood by pushing down and tilting filters out . 3 ] remove the ez1 brackets from inside the hood by cutting o...
Page 10: Inst
Inst alla tion manual inst alla tion 10 5 ] remove 7” round duct plate from top/back of hood (see illustration below). Recirculation cover plate screws 6 ] remove electrical power cable knockout from top (vertical exhaust) or back (horizontal exhaust) of hood. Install an appropriate strain relief, 1...
Page 11: Inst
Inst alla tion manual inst alla tion 11 ducted installation only tip : insert a small length of duct over the 3¼” x 10” damper assembly (for rectangular ducting) or 7” round (for round ducting) and seal the joint using aluminum foil duct tape to ease connection with the house ductwork. 8 ] remove 3¼...
Page 12: Inst
Inst alla tion manual inst alla tion 12 prepare the hood location this manual covers 2 kinds of installation: the standard (without ez1 brackets) and the ez1 one-person installation system (using included template and brackets). For the standard installation, go to page 17. Ez1 one-person installati...
Page 13: Inst
Inst alla tion manual inst alla tion 13 framed cabinet 7/64” refer to the marking on brackets to determine the correct installation side and orientation. Mate the corresponding bracket to the cabinet side frame, while placing rear end of bracket against the wall. Use a pencil to mark 3 holes (there ...
Page 14: Inst
Inst alla tion manual inst alla tion 14 7/64” 3 x refer to the marking on brackets to determine the correct installation side and orientation. Align the corresponding bracket to the cabinet side, while placing rear end of bracket against the wall. Draw a line on the outer edge of the bracket (as sho...
Page 15: Inst
Inst alla tion manual inst alla tion 15 horizontal exhaust installation vertical exhaust installation ote: n the following procedure applies to both frame or frameless cabinet installations. Install the hood (ez1 bracket) 1 ] run house power cable between service panel and hood location. 2 ] there a...
Page 16: Inst
Inst alla tion manual inst alla tion 16 7 ] for framed cabinet, secure the hood to the ez1 brackets using four (4) no. 8-18 x 1/2” metal screws with washers. For frameless cabinet, secure the hood to the cabinet using four (4) no. 8 x 5/8” round head wood screws (screws and washers included in parts...
Page 17: Inst
Inst alla tion manual inst alla tion 17 standard installation (without ez1 brackets) 1 ] use the proper diagram below for placement of ductwork and electrical cutout in cabinet or wall. For a non-ducted installation, do not cut a duct access hole, only cut the hole for electrical wiring. 2 ] install...
Page 18: Inst
Inst alla tion manual inst alla tion 18 install the hood (standard installation) 1 ] run house power cable between service panel and hood location. Run the house power cable into the hood through the strain relief previously installed in step 6 on page 10. 2 ] hang hood from (4) mounting screws prev...
Page 19: Inst
Inst alla tion manual inst alla tion 19 connect the wiring 1 ] connect house power cable to range hood wiring: black to black, white to white and green or bare wire under green ground screw. ! Warning risk of electric shock. Electrical wiring must be done by qualifi ed personnel in accordance with a...
Page 20: Inst
Inst alla tion manual inst alla tion 20 light bulbs (vblsh1 series only) 1 ] align the bulb leads with the small indentations located on the border of the lamp location on hood (see inset above), then install the bulbs by placing the bulb leads into their grooves in the socket. 2 ] gently push upwar...
Page 21: Wiring Diagram
Inst alla tion manual wiring diagram 21 1 2 3 4 5 6 1 2 3 4 j6 override j4 led j1 0 int erf ace 1 2 3 4 5 6 7 8 user interface mounted to j10 on back of control board. J1 t ransf or mer j2 p o w e r, mot or 5 4 3 2 1 5 4 3 2 1 6 7 control board r bk r r bl bl bk w bk bk w g/y r (low) o (medium) bk (...
Page 22: Service P
Inst alla tion manual service p ar ts 22 r eplacement p arts and r epairs in order to ensure your unit remains in good working condition, you must use venmar ventilation ulc genuine replacement parts only. The venmar ventilation ulc genuine replacement parts are specially designed for each unit and ...
Page 23: Service P
Inst alla tion manual service p ar ts 23 k ey no . P art no . D escription q uantity 30" s tainless 30" w hite 30" b lack 1 s97020029 r ecirculation cover plate , b lack ( including screws ) 1 s97020030 r ecirculation cover plate , w hite ( including screws ) 1 s97020031 r ecirculation cover plate ,...
Page 24: Arranty
Inst alla tion manual w arranty 24 limited warranty warranty period and exclusions: venmar ventilation ulc (the “company”) warrants to the original consumer purchaser of its product (“you”) that the product (the “product”) will be free from material defects in the product or its workmanship for a pe...