Vent-Axia 45 90 49 (Pullcord) Installation And Wiring Instructions - page 3
3
FIXING HOLES
A
INSTALLATION.
PANEL MOUNTING
1. Cut a 105mm
∅ hole through the panel.
2. Remove the Indoor Grille [A]. Insert a small bladed screwdriver into the slot at the base of the Grille, push the
release catch in and gently lever the Grille upwards away from the Inner Cover [B].
3. Remove Inner Cover [B]. Insert a small bladed screwdriver into the slot on the sides of the Cover, push the
release catch in and gently lever the cover away from the Base Housing [D].
4. Remove the Cable Grommet [C], pierce/cut a hole in the Grommet to suit the cable size, maintaining the
integrity of the seal and replace the grommet in the Base Housing to suit either a top or back cable entry.
5. Slide the Base Housing into the hole in the panel and secure into position using screws and fixings provided.
Fig. 1.
6. Ensure the fan blade rotates freely.
7. Select and follow the appropriate wiring diagram in Section B WIRING.
8. Replace the Inner Cover and Indoor Grille.
9. Switch the mains power supply on and check the fan is operating correctly.
WALL MOUNTING
1. Cut a 115mm.
∅ hole through the wall and insert the wall sleeve with the larger diameter sleeve on the room
side and cement both ends into position flush with the wall faces. The wall sleeve should be angled downwards
away from the fan to allow any condensation to drain to the outside wall.
2. Using the Back Plate as a template, mark the fixing hole centres on the wall. Drill and plug the wall and fix the
Back Plate into position.
3. Fix the Outside Grille [F] on to the Back Plate (screws provided). Ensure the louvres are pointing downwards.
4. Remove the Indoor Grille [A]. Insert a small bladed screwdriver into the slot at the base of the Grille, push the
release catch in and gently lever the Grille upwards away from the Inner Cover [B].
5. Remove Inner Cover [B]. Insert a small bladed screwdriver into the slot on the sides of the Cover, push the
release catch in and gently lever the cover away from the Base Housing [D].
6. Remove the Cable Grommet [C], pierce/cut a hole in the Grommet to suit the cable size, maintaining the
integrity of the seal and replace the grommet in the Base Housing to suit either a top or back cable entry.
7. Slide the Base Housing into the Wall Liner and secure into position using screws and fixings provided (Fig. 1.).
8. Ensure the fan blade rotates freely.
9. Select and follow the appropriate wiring diagram in Section B WIRING.
10. Replace the Inner Cover and Indoor Grille.
11. Switch the mains power supply on and check the fan is operating correctly.
WINDOW MOUNTING
1. Cut a 105mm
∅ hole in the glass.
2. Ensure that the glass surfaces are clean and free from grease.
3. Remove the Indoor Grille [A]. Insert a small bladed screwdriver into the slot at the base of the Grille, push the
release catch in and gently lever the Grille upwards away from the Inner Cover [B].
4. Remove Inner Cover [B]. Insert a small bladed screwdriver into the slot on the sides of the Cover, push the
release catch in and gently lever the cover away from the Base Housing [D].
5. Remove the Cable Grommet [C], pierce/cut a hole in the Grommet to suit the cable size, maintaining the
integrity of the seal and replace the grommet in the Base Housing to suit a top cable entry.
6. Fit required spacers behind the fan back plate, engaging the locating pips. Place the fan spigot through the hole
in the glass from the inside, with a gasket on each side of the glass.
7. From the outside, place on the remaining spacer, with the locating pips facing outwards. For double-glazing and
materials up to 40mm thick, one or more spacers may be discarded.
8. Draw the assembly together with the threaded fixing ring. Do not over-tighten.
9. Fix the Outside Grille [F] on to the Spacer (screws provided). Ensure the louvres are pointing downwards.
10. Ensure the fan blade rotates freely.
11. Select and follow the appropriate wiring diagram in Section B WIRING.
12. Replace the Inner Cover and Indoor Grille.
13. Switch the mains power supply on and check the fan is operating correctly