VentAHood DAH18 Installation Instructions Manual

Manual is about: WALL MOUNT RANGE HOOD

Summary of DAH18

  • Page 1

    Vp562/vp563 transition centers outlet over top of hood wall mount range hood specifications dah18/pwvh18/xrh18/xrxh18 wbar warming light bar is available on selected models. X in part number indicates 27" depth. *recommended mounting height is for optimum performance. 900 cfm b200 dual & b100 single...

  • Page 2: Installation Instructions

    Page 1 l110 1015 ul c us r read and save these instructions all hoods must be installed by a qualified installer installation instructions wall mount hood read all instructions thoroughly before beginning installation warning - to reduce the risk of fire, electric shock, or injury to persons, observ...

  • Page 3: Ducting Do’S and Don’Ts

    Page 2 l110 1015 ducting do’s and don’ts yes no smooth duct smooth gradual turn proper combining of two ducts flexible duct sharp angled turns improper combining of two ducts general requirements • observe local codes regarding special duct requirements and placement of duct against combustibles. • ...

  • Page 4: Installation Details

    Page 3 l110 1015 installation details 1) read all instructions thoroughly before beginning installation. Note: these instructions apply to standard hoods only. Custom hoods may require additional specification consideration. 2) when installing a wall mount range hood, it is recommended that the bott...

  • Page 5

    Page 4 l110 1015 6” outlet vent hole 3 ¼” electrical centerline of hood wall side 1 ¾” 1 3⁄8” 5 ¼” electrical 1 ¾” centerline of hood 8” outlet vent holes 5 ¼” 5 ½” wall side 8” outlet 6” outlet 5 ¼” wall side vent holes centerline of hood electrical (2) 5 ½” 7 5⁄16” 1 7⁄8” 7 5⁄16” 1 ¾” 11” 11” 5 ½”...

  • Page 6

    Page 5 l110 1015 8) install an appropriate 1/2" ul listed electrical wire clamp through each motor box electrical opening on top of the hood. Install electrical wiring from the service panel to the hood location for each motor box. Consult the connection diagrams (on previous page) for further detai...

  • Page 7

    Page 6 l110 1015 14) for back venting applications only. If you are not back venting, proceed directly to step 15. Method 1: place the appropriate elbow(s) on the top of the hood. Elbow(s) should be placed with the non-crimped end(s) on the inside the collar(s) of the exhaust outlet(s). Use duct tap...

  • Page 8: Venting

    Page 7 l110 1015 venting accessories 6” rectangular duct pipe model dim vp507 6” x 8 ½” 24” 8 ½” 6” round duct pipe model dim vp500 vp501 vp502 6” round 7” round 8” round 36” 6” 7” 8” 3 ¼” rectangular duct pipe model dim vp504 vp505 vp506 3 ¼” x 10” 3 ¼” x 12” 3 ¼” x 16” 30” 10” 12” 16” 3 ¼” offset ...

  • Page 9

    Back vent applications (page 1 of 4) hood model/hood style back vent diagram k250 (3-1/4” x 10”) b100 (6” round) b200 (8” round) b300 (8” round & 6” round) b400 (two 8” round) k-series under cabinet hood and liner insert a standard n/a n/a n/a n/a 6” under cabinet (excluding k-series) b n/a vp513 vp...

  • Page 10

    Diagram a - direct back vent (drawing not to scale) side view 3 1/4” x 10” rectangular diagram b - off the top (drawing not to scale) side view vp513 - 6” round vp515 - 8” round vp561 - 8” round to 6” x 8 1/2” rectangular 8” round diagram c - within the height of the hood (drawing not to scale) side...

  • Page 11

    10” 4 ¼” 3 ¼” hood c/l level of blower deck 6” 8 ½” 3 ¼” hood c/l level of blower deck 8” 10 ¾” hood c/l level of blower deck 6” 7” hood c/l level of blower deck 8 ½” vp513 - 6” round vp515 - 8” round vp561 - 8” round to 6” x 8 1/2” rectangular vp559 - 3 1/4” x 10” rectangular back vent applications...

  • Page 12

    8” 10 ¾” 6” 8 ½” level of blower deck hood c/l 14 ⁄ ” 7 ⁄ ” 7 ⁄ ” 6” 7” 8 ½” 6” 8 ½” level of blower deck hood c/l 14 ⁄ ” 7 ⁄ ” 7 ⁄ ” vp513 - 6” round vp515 - 8” round vp561 - 8” round to 6” x 8 1/2” rectangular back vent applications (page 3 of 4) note: excluding the slh6-k, under cabinet...

  • Page 13

    8” 10 ¾” level of blower deck hood c/l 22” 11” 11” 8” 10 ¾” 8 ½” 8 ½” 6” 7” level of blower deck hood c/l 22” 11” 11” 6” 7” vp513 - 6” round vp515 - 8” round vp561 - 8” round to 6” x 8 1/2” rectangular back vent applications (page 4 of 4) note: excluding the slh6-k, under cabinet range hood and the ...

  • Page 14

    Page the information in this document is subject to change at any time without notice. Vent-a-hood venting accessories wall louver 6” 7” 8” 8 5⁄8” back view 1 ½” flange wall louver 11” 11” back view 1 ½” flange wall louver 13” 13” back view 1 ½” flange rectangular wall louver 3 ¼” 10” 8 ½” 6” 1 ½” f...

  • Page 15

    Page the information in this document is subject to change at any time without notice. Parts for vent-a-hood products motors part no. Description price p1301-1 single speed white motor (cw) p1301-2 two speed white motor (cw) p1302-1 black motor (ccw) p1315 k series motor p1900 adapter (amp plug/two ...