- DL manuals
- Vents
- Air Handlers
- VUT 1000 H
- User Manual
Vents VUT 1000 H User Manual
Summary of VUT 1000 H
Page 1
РУКОВОДСТВО ПОльзОВаТеля РУКОВОДСТВО ПОльзОВаТеля user’s manual vut 350 h vut 500 h vut 530 h vut 600 h vut 1000 h vut 2000 h heat recovery air handling unit.
Page 2
2 contents safety requirements 3 introduction 5 use 5 delivery set 5 designation key 5 technical data 6 unit design and operating logic 8 mounting and set-up 9 condensate drainage 10 connection to power mains 11 unit control 12 maintenance 13 fault handling 14 storage and transportation rules 14 man...
Page 3
3 safety requirements • read the user’s manual carefully prior to the operation and installation of the vut … h heat recovery air handling unit. • fulfil the user’s manual requirements as well as the provisions of all the applicable local and national construction, electrical and technical codes and...
Page 4
4 do not touch the unit controls with wet hands. Do not carry out the unit mainte- nance with wet hands. Use the unit only as intended by the manufacturer. Do not connect a clothes dryer or other similar equipment to the unit or the ventilation system. Do not wash the unit with water. Protect the un...
Page 5: Vut Х H
5 introduction this user’s manual includes technical description, operation, installation and mounting guidelines, technical data for the vut … h heat recovery air handling unit, hereinafter referred to as “the unit”. Use • due to the ability to save heating energy by means of energy recovery the un...
Page 6
6 technical data the air-handling unit is intended for operation in closed spaces under ambient air temperatures from +10 ºc to +50 ºc. Hazardous parts access and water ingress protection rating: ip 44 for the unit motors; ip 22 for the assembled unit connected to the air ducts. The unit design is c...
Page 7
7 unit technical data parameter vut 350 h vut 500 h vut 530 h vut 600 h vut 1000 h vut 2000 h unit supply voltage, 50 hz [v] 1~ 230 total unit power [w] 260 300 300 390 820 1300 total unit current [a] 1,2 1,32 1,32 1,72 3,6 5,68 max. Air capacity, m 3 /h 350 500 530 600 1200 2200 prm 1150 1100 1100 ...
Page 8
8 unit design and operating logic unit operation logic: warm stale extract air from the room flows to the unit, where it is filtered, then air flows through the heat exchanger and is exhausted outside by the extract fan. Clean cold air from outside is moved to the supply filter. Then filtered air fl...
Page 9
9 mounting and set-up the unit may be suspended on threaded rods that are fixed inside a dowel or may be rigidly fixed on a horizontal plane. While mount- ing the unit provide enough access for maintenance or repair work. Unit ceiling mounting unit floor mounting safety precautions: in a floor-mount...
Page 10
10 connect the switch according to the wiring diagram (see page 12). Place the executive part of the switch into the mounting box. Secure the executive part of the switch by means of two screws (included in the delivery set). Cover the executive part of the switch with the decorative front panel and...
Page 11
11 connection to power mains the power mains connection shall only be performed by qualified personnel after careful reading of this user’s manual. Connect the unit to an ac power supply with the voltage corresponding to the value specified in the table of technical data. Make sure that the cable is...
Page 12
12 vut ... H air-handling units must be connected to the power mains in accordance with the wiring diagram and the terminal designations given inside the terminal box or the control unit: l n pe qf x1 n l vut 350 ... 600 h electrical connections diagram l n pe qf vut 1000 ... 2000 h electrical conne...
Page 13
13 maintenance the unit must undergo technical maintenance 3 to 4 times a year. Maintenance includes general cleaning of the unit and the following operations: 1. Filter maintenance (3-4 times per year). Dirty filters increase air resistance in the system and reduce supply air volume. The filters re...
Page 14
14 6. Technical maintenance of air duct system (every 5 years). Even regular fulfilling of all the prescribed above maintenance operations may not completely prevent dirt accumulation in the air ducts which reduces the unit capacity. The air duct maintenance includes their periodic cleaning or repla...
Page 15
15 manufacturer’s warranty the manufacturer hereby warrants normal operation of the unit over the period of 24 months from the retail sale date provided the user’s observance of the transportation, storage, installation and operation regulations. Should any malfunctions occur during the unit operati...
Page 16
16 acceptance certificate product type heat recovery air handling unit model vut______ h serial number manufacturing date we hereby declare that the product complies with the essential protection requirements of electromagnetic council directive 2004/108/ec, 89/336/eec and low voltage directive 2006...
Page 17
17 warranty card product type heat recovery air handling unit model vut______h serial number manufacturing date sales date warranty period sales company seller’s seal notes _________________________________________________________________________________________________ _____________________________...
Page 18
V26en-02.