Venturer CMP6937 Operating Instructions
MICRO MP3 / CD MUSIC SYSTEM
with SUBWOOFER
OPERATING INSTRUCTIONS
Printed in China 811-693791-011
TO PLAY MP3 (for remote only)
This set can read MP3.
1. Press the FUNCTION button to CD.
2. To open CD door. Place a MP3 disc in the center with the label face front. The
total albums and the total tracks appear on the display.
3. Press the PLAY/PAUSE
button to start play.
4. Press the STOP
button to stop playback.
5. In stop mode, press PLAY/PAUSE
button to start playback.
TO SEARCH AN ALBUM
Basically this system supports the album search mode to search an album at high-
speed.
1. Press the PRESET + / ALBUM + or PRESET – / ALBUM – button to search a desired
album in play /stop mode.
2. After selected a desired album, the first track of this album will be shown on the
display within two seconds.
3. Press the SKIP/SEARCH
/
button to search a desired track and then press
the PLAY/PAUSE
button to play the track.
4. During searching the album, the album number is shown on the display.
USING THE REMOTE CONTROL CORRECTLY
• Point the Remote Control at the REMOTE SENSOR located on the unit.
• When there is a strong ambient light source, the performance of the infrared
REMOTE SENSOR may be degraded, causing unreliable operation.
• The recommended effective distance for remote operation is about 6 meters (19
f e e t ) .
SEARCH A FILE (SONGS) BY FILE NAME
1. Press the MP3 MODE button once the "
" will blink, the file name and the
number's tracks appear on the display.
2. Press the SKIP/SEARCH
/
buttons one by one to find the file name, the
file name will display sequence as "A,B ........... Z, 0 .......... 9".
3. Press the SKIP/SEARCH
/
buttons about 2 seconds, the capital letters or
the figure will blinks. If the first letter of the file name in this disc haven't the
capital letters or the figure, it will not blink.
4. Press the SKIP/SEARCH
/
buttons one by one to search file.
5. Press the PLAY/PAUSE
button to play select file.
SEARCH A FILE (SONGS) BY ALBUM
1. Press the MP3 MODE button twice times, the "
" will light and ALBUM appear
on the display.
2. Press the SKIP/SEARCH
/
buttons one by one, to select album.
3. Press the SKIP/SEARCH
/
buttons about 2 seconds until "ALBUM" disappear.
4. Press the SKIP/SEARCH
/
buttons one by one to search file.
5. Press the PLAY/PAUSE
button to play select file.
1. FM MONO / STEREO / MP3 MODE /
CD ESP ON/OFF button
2. STANDBY/ ON button
3. FUNCTION (CD/AUX/TUNER) button
4. PRESET+ / ALBUM+ button
5.
STOP / BAND button
6.
TUNING /
SKIP / SEARCH button
7. MEMORY
button
8. PRESET– / ALBUM– button
9. SLEEP button
10. REPEAT button
11.
PLAY / PAUSE button
12.
TUNING /
SKIP / SEARCH button
13. X-BASS button
14. RANDOM button
15. TIMER button
16. VOLUME +\– controls
TO REPEAT THE WHOLE DISC
Press the REPEAT button a second
time to repeat all tracks, the repeat
all indicator will light.
REPEAT PLAY (for remote only)
This function will allow a single tracks or all the tracks on the disc to be played
repeatedly.
TO REPEAT THE SAME TRACK
Press the REPEAT button once during
playback, the repeat one indicator
will light.
TO CANCEL REPEAT PLAY
Press the REPEAT button until "REPEAT" indicator is switched off.
RANDOM PLAY (for remote only)
All the tracks on the disc can be played in random order.
Press the RANDOM button.
RANDOM appears in the display and the disc will play automatically.
TO CANCEL RANDOM PLAY
Press the STOP
or RANDOM button so that "RANDOM" in the display goes
out.
TO REPEAT PLAY THE ALBUM (in MP3 Mode) (for remote only)
Press the REPEAT button three times to repeat the album, the repeat album
indicator will light.
TO CANCEL REPEAT PLAY
Press the REPEAT button until "REPEAT & ALBUM" indicator is switched off.
This product contains a low power laser device.
WARNING: TO REDUCE THE RISK
OF ELECTRIC SHOCK, DO NOT RE-
MOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS IN-
S I D E . R E F E R S E R V I C I N G T O
QUALIFIED SERVICE PERSONNEL.
The lightning flash and
arrowhead within the
triangle is a warning
sign alerting you of
"dangerous voltage"
inside the product.
The exclamation point
within the triangle is a
warning sign alerting
you of important in-
structions accompany-
ing the product.
CAUTION
INVISIBLE LASER RADIATION WHEN
OPEN AND INTERLOCKS DEFEATED.
AVOID EXPOSURE TO BEAM
CLASS 1 LASER
P R O D U C T
APPAREIL Á LASER
DE CLASSE 1
CAUTION : Use of any controls, adjustments, or procedures other than those speci-
fied herein may result in hazardous radiation exposure.
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
CLASS 1 LASER PRODUCT
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Should any trouble occur, disconnect the AC power cord and refer
servicing to qualified personnel.
SAFETY PRECAUTIONS
Follow the advice below for safe and appropriate operations
ON PLACEMENT
• Do not use the unit in places which are extremely hot, cold, dusty or
humid.
• Place the unit on a flat and even surface.
• Do not restrict the air flow of the unit by placing it in a place with poor air
flow, by covering it with a cloth, or by placing it on a carpet.
ON SAFETY
• When connecting and disconnecting the AC cord, grip the plug and not the
cord itself. Pulling the cord may damage it and create hazard.
• When you are not going to use the unit for a long period of time, disconnect
the AC power cord.
ON AC VOLTAGE
• Before use, check that the rated voltage of your unit matches your local
voltage.
FCC INFORMATION
This device complies with part 15 of FCC Rules. Operations are subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesirable operations.
ON CONDENSATION
• When left in a heated room where it is warm and damp, water droplets or
condensation may form inside the CD player.
• When there is condensation inside the unit, it may not function normally.
• Let it stand for 1 to 2 hours before turning the power on, or gradually heat
the room up and dry the unit before use.
VENTILATION WARNING
• The normal ventilation of the product shall not be impeded for intended
use.
RATING PLATE LOCATION
The rating plate location is on the bottom of product.
GENERAL
Power consumption:
25W
Power source:
AC ~120V 60 Hz (USA and Canada)
AC ~220V 50 Hz (China)
AC ~230V 50 Hz (Europe)
AC ~240V 50 Hz (Australia)
AC ~110-120V/220-240V 50/60Hz (Others)
SPECIFICATION
Specifications may be subject to change without notice.
TROUBLE SHOOTING TIPS
RADIO
Disc skips
System does not turn on
Problem
Solutions
Disc in place but unit
won't play
CD/MP3
• Make sure AC power plug is secure in the
outlet, and outlet has power.
• Make sure FUNCTION switch is set to CD.
• Make sure disc label is facing up.
• Make sure disc is clean.
• Pause mode is activated.
• Disc may be damaged or dirty; check disc.
• Make sure the unit is on a secure spot.
Vibration or jarring can cause the disc to
skip.
Poor FM reception
Poor MW reception
• Make sure FM antenna wire is unwound.
• Electrical interference in your home can
cause poor reception. Move the unit away
from sources of interference (especially those
with motors and transformers).
• Set the AM/MW loop antenna to a direction
for the better reception.
1
2
3
4
5
6
7
10
11
12
13
14
15
16
8
9
TO CHANGE REMOTE BATTERY
1. Open the battery
door.
2. Insert one CR2025 (3V)
size battery.
BATTERY REPLACEMENT
When battery become weak, the operating distance of the Remote Control is
greatly reduced and you will need to replace the battery.
NOTE:
If the Remote Control is not to be used for a long time, remove the battery to avoid
damage caused by battery leakage corrosion.
WARNING:
Do not dispose of batteries in fire, batteries may explode or leak.
ATTENTION
Take out the PVC sheet
before operating
the Remote
Control.
REMOTE CONTROL
CARE & MAINTENANCE
CLEANING CD
If the CD skips or will not play, the disc may
need cleaning. Before playing, wipe the disc
from the centre out with a cleaning cloth. After
playing, store the disc in its case.
CLEANING THE UNIT
Do not use volatile chemicals on this unit. Clean by lightly wiping with
a soft cloth.
IMPORTANT NOTICE:
• Should the CD door be opened before the reading of the CD is
completed, a jamming noise may occur. This can be resolved by
closing the CD door and then setting the FUNCTION switch
temporarily to AUX.
• If an abnormal display indication or an operating problem occurs,
disconnect the AC power cord. Wait at least 5 seconds, then reconnect
the AC power cord.
• Before transporting the unit, remove the disc from the CD tray.
PROGRAMMING TRACKS - in the MP3 stop mode (Up to a maximum of 64
tracks)
1. Press the MEM
button, the ALBUM blinks on the display.
2. Press the SKIP/SEARCH
/
buttons to select the desired albums.
3. Press the MEM
button, the FILE (SONGS) blinks on the display.
4. Press the SKIP/SEARCH
/
buttons to select the desired files (songs).
5. Press the MEM
button again.
6. Repeat alone step 2 and 5 procedure to program additional tracks. Press PLAY/
PAUSE
button to start playback of the programmed tracks and memory
indicator will appear on display.
To check the program
While in the stop mode, press the MEM
button. The album , file (songs) and
program numbers will appear on the display.
Press the MEM
button again to view the other programmed selections.
These displays do not appear during programmed play.
To play the programmed tracks
Press the PLAY/PAUSE
button.
To stop programmed play
Press the STOP
button, if you want to recover programmed play. You can first
press MEM
button and then press PLAY
button again.
To clear the memory content
Press the STOP
button and then open the CD door or press MEM
button and
then press the STOP
button in stop mode.