Atina 500 / vertex 700 model numbers: nabg50rn, nabg50rp/ nvbg70rn, nvbg70rp. This is not a `do-it-yourself` product the appliance must be installed by a gas safe registered person installation, servicing and users instructions these products are approved to the european gas directive please leave t...
2 important notes – please read before undertaking the installation 1. The chimney must be swept before the appliance is fitted. 2. The installation instructions must be adhered to without exception. List of components a) firebox complete with burner and controls. B) installation, servicing & users ...
3 2 the 500 & 700 fireboxes can be fitted into fireplaces which are large enough or can be altered to accept these boxes. Their dimensions are shown in figure 1. If the fireplace has to be altered a lintel may be required to support the masonry over the opening. 3 decorative infill panels these appl...
4 4 the hearth (appliances in floor level fireplaces) where the appliance is fitted in a floor level builders opening, floor level fireplace recess or floor level flue box, the hearth shall: a) extend through the whole base of the builders opening, fireplace recess or beneath the flue box. B) projec...
5 7 ventilation. 500 model subject to a satisfactory spillage test, there is no requirement for purpose made ventilation with these models. 700 model the room containing the appliance must have a permanent air vent with an effective open area of at least 100 cm 2 . The vent must be either direct to ...
6 chimney over the period of a few minutes and recheck. If there is any doubt about the soundness of the chimney a smoke pellet should be used after preheating the flue and if smoke still fails to clear, further investigation of the chimney is required and the appliance must not be fitted until any ...
7 in the base of the firebox. Re-connect the gas supply. Inset four aa batteries into the battery holder and return it and its carrier to its position at the end of the burner. (note; the tab at the front of the battery carrier top should be inserted into its slot and the whole carrier drawn forward...
8 note: sometimes a ‘popping’ noise is produced by the burner at maximum. This is caused by a flame repeatedly lighting and then going out. To correct this, carefully examine the fire and try to identify the flame responsible for the noise. Turn the fire out and with a screwdriver or similar move ei...
9 briefing the user 1 demonstrate the full operation of the appliance to the customer, referring them specifically to the glass gravel, black ceramic granules or limestone pebbles, any decorative ceramic shapes and the removal of soot as described in these instructions. 2 inform the customer that al...
10 u sers g uide useful tips & recommendations once your fire has been fitted, the following recommendations are made to ensure you enjoy the best results from your purchase; 1 the installation of this appliance must have been carried out by a qualified installer and in accordance with the requireme...
11 lighting the appliance 1 fitting the battery to the handset before using the appliance remove the access cover in the rear of the handset and insert a 9 volt pp3 size battery. Connect the battery by pushing the connector on to the terminals. Make sure the battery is connected correctly. Replace t...
12 position which is indicated by the symbol o. Caution should be exercised as this switch is situated quite close to the pilot flame. Switch back to the on position to allow the appliance to be re-lit when required. Cleaning the fire 1 ensure that the fire is cold before undertaking any cleaning. R...
13 unclip the battery from its connector and put a new one put in its place. Replace the cover. 10 burner: (see figure 4) wait until the fire is cold before attempting to change these batteries which are in a carrier at the left hand side of the burner. Grip the separate piece of grille at the left ...
14 installation & service record please ensure that installer completes the installation record below installation record appliance supplied by: ………………………….... Installation date: ……………serial no.: ….……... Installed by: …………..…...Gas safe no.: …..…… signed by installer: ………………………..… record of 1 st ser...
15 b-111620 issue 3 bfm europe limited trentham lakes stoke on trent, staffordshire st4 4tj tel: (01782) 339000 fax: (01782) 339009 email: info@bfm-europe.Com www.Bfm-europe.Com this booklet contains 15 pages. Atina/vertex/1007/ii/ui.
