- DL manuals
- Verine
- Heater
- Marcello NBFP00RN
- Installation, User And Servicing Instructions
Verine Marcello NBFP00RN Installation, User And Servicing Instructions
Summary of Marcello NBFP00RN
Page 1
Marcello balanced flue convector model numbers: nbfp00rn, nbfp00rp installation, user and servicing instructions these instructions must remain with the user this appliance meets the requirements of the european gas directive 0087.
Page 2
2 contents page no. List of components 3 appliance data 3 g eneral i nstallation r equirements 3 fitting the appliance 3 placing of decorative refractory shapes 9 c ommissioning 10 u sers g uide 11 useful tips & recommendations 11 operation of the fire 11 opening and closing the fascia panel 11 ligh...
Page 3
3 list of components before commencing the installation ensure that all the components listed below are included in the appliance packaging. A) balanced flue convector b) ceramic components; i) 1 packet black ceramic granules ii) 1 packet of 12 ‘cotswold stone’ pieces iii) 1 packet of 22 ‘cotswold s...
Page 4
4 centre of the glass window is 157mm below the centre of the flue terminal. The centre of the terminal should be positioned at least 700mm above floor level to allow space for the fascia to drop down on its runners. If the fireplace has to be altered a lintel will be required to support masonry ove...
Page 5
5 4 decorative fascia panel this appliance must be installed with the fascia panel set supplied. This panel allow the passage of air for convection and for the cooling of the control system. It must be installed as described in these instructions. The fire should never be left running with this fasc...
Page 6
6 10 combustible walls & timber framed dwellings the appliance may be fitted directly to wall made both from combustible and non combustible material. If it is to inset into the wall, the inner wall plate (supplied separately) must be used and a gap of 25mm should be maintained between the top, rear...
Page 7
7 the wall using screws and wall plugs. Make sure the plate is fixed the correct way up. (see figure 3) slide the flue further into the wall until the tabs on the wall plate line up with the holes in the outer flue tube. Temporally fix the tube to the wall plate with the self tapping screws provided...
Page 8
8 page 2 of these instructions inset installation 1 to inset the marcello gas fire, a wall plate, supplied separately, must be used. 2 select a position for the appliance and the height required from the centre of the glass panel to the floor. Cut a hole in the inner leaf of the cavity wall to the d...
Page 9
9 flue outer ring and into the outer flue tube. Secure in place with self tapping screws and then cover and seal the joint with the length of aluminium tape supplied. Thread the fibreglass rope ring sealing gasket on to the flue. 7 the gas supply should be routed from the meter or cylinder to a poin...
Page 10
10 6 place ten ‘cotswold stone’ pieces from the second packet on top of the black ceramic granules in front of the front air guide as shown in figure 6. 7 place the remaining ten ‘cotswold stone’ pieces from the second packet across the air guides pushing each piece down on a location spike formed i...
Page 11
11 4 advise the importance of having the appliance serviced on an annual basis..
Page 12
12 u sers g uide : useful tips & recommendations once your fire has been fitted, the following recommendations are made to ensure you enjoy the best results from your purchase; 1 the installation of this appliance must have been carried out by a qualified installer and in accordance with the require...
Page 13
13 lighting the appliance 1 lighting: see figure 8. A push in and turn control knob ‘a’ anti-clockwise to the pilot position. B hold knob ‘a’ in for several seconds to purge any air from the system. C with knob ‘a’ still depressed turn it from the "off" position to the "pilot” position until the pil...
Page 14
14 3 adjusting the flame height using the remote control handset (figure 9) the remote control system fitted to the fire uses ultrasound to transmit signals between the handset and the fire. It will work best if the grill at the front of the handset is pointed in the direction of the fire. To preven...
Page 15
15 s ervice and m aintenance before any servicing is carried out isolate the appliance from the gas supply. After refitting the appliance, check for gas soundness at all gas joints and test for spillage. This product uses fuel effect pieces containing refractory ceramic fibre (rcf). This material co...
Page 16
16 c remove the screw holding the pilot draught shield to the pilot bracket and lift the shield away. D remove the six screws securing the control mount platform to the firebox. Take care not to damage the gasket. 9 replace the control mount platform (if it has been removed) and secure with the six ...
Page 17
17 spare parts list in the event of a part requiring replacement the parts list is as follows part description part number motorised valve cv-104103 remote hand control & receiver cv-104413 pilot burner ng model cv-104506 pilot burner lpg model cv-104513 injector ng model cv-104608 injector lpg mode...
Page 18
18 installation & service record please ensure that installer completes the installation record below installation record appliance supplied by: ………………………….... Installation date: ……………serial no.: ….……... Installed by: …………..…...Corgi no.: …..…… signed by installer: ……………………………..… record of 1 st serv...
Page 19
19 b-111770 issue 2 bfm europe limited trentham lakes stoke on trent, staffordshire st4 4tj tel: (01782) 339000 fax: (01782) 339009 email: info@bfm-europe.Com www.Bfm-europe.Com.