1. DL manuals
  2. Verint
  3. Transmitter
  4. Nextiva S1100w
  5. User Manual

Verint Nextiva S1100w User Manual

Other manuals for Nextiva S1100w: User Manual
Manual is about: wireless video transmitters

Summary of Nextiva S1100w

  • Page 1

    Nextiva s1100w user guide firmware release 4.12 august 2007.

  • Page 3: Nextiva S1100W

    Nextiva s1100w firmware release 4.12 user guide verint video intelligence solutions revision: a.

  • Page 4

    This document contains confidential and proprietary information of verint systems inc. And is protected by copyright laws and related international treaties. Unauthorized use, duplication, disclosure or modification of this document in whole or in part without the written consent of verint systems i...

  • Page 5

    Verint video intelligence solutions iii nextiva s1100w user guide warning: if you connect multiple devices on the same 24v ac power supply, always wire them the same way: the red power wires of all devices must be on the same power supply terminal. Since the black power wire of the device is interna...

  • Page 6

    Iv verint video intelligence solutions.

  • Page 7: Contents

    Verint video intelligence solutions v contents preface .............................................................................................................. Vii who should read this guide ............................................................................Viii how to use this guide ...

  • Page 8

    Contents vi verint video intelligence solutions installing an antenna .................................................................................27 performing the rs-422/485 serial connection ...............................................27 configuring the i/os ..................................

  • Page 9: Preface

    Verint video intelligence solutions vii preface the nextiva s1100w user guide presents the information and procedures for installing, configuring, and using the nextiva tm s1100w wireless video transmitters..

  • Page 10: Who Should Read This Guide

    Preface viii verint video intelligence solutions who should read this guide this guide is intended for managers, it system administrators, engineers, and technicians who will use the s1100w edge devices. It provides conceptual information on how to configure, install, and operate the devices. This g...

  • Page 11: Related Products

    Verint video intelligence solutions ix nextiva s1100w user guide related products you use the s1100w devices with the nextiva s3100 multipurpose outdoor access point. You may also use them with the ndvr tm and nextiva enterprise management and storage solutions. For more details about any of these p...

  • Page 12: Warranty

    Preface x verint video intelligence solutions warranty each product manufactured by verint systems is warranted to meet all published specifications and to be free from defects in material and workmanship for a period of two (2) years from date of delivery as evidenced by the verint systems packing ...

  • Page 13: Overview

    Verint video intelligence solutions 1 overview the s1100w allows digital video transmission over license-free and licensed bands. It delivers high-quality mpeg-4-based video at 30 frames per second in ntsc (25 in pal) over local and wide area networks (lans and wans). This wireless edge device is bu...

  • Page 14: About The S1100W

    1: overview 2 verint video intelligence solutions about the s1100w the s1100w devices come as transmitters only. You can buy 12v dc or 24v ac devices. The s1100w covers the 2.4 ghz and 5 ghz frequency bands in north america and europe. It also covers the 4.9 ghz public safety band in north america. ...

  • Page 15: Shipment

    Verint video intelligence solutions 3 nextiva s1100w user guide the s1100w devices can have the following video resolutions and maximum frame rates (in frames per second), using the ntsc (pal) format: * without noise, i/os, and other factors affecting quality, the device can achieve the highest fram...

  • Page 16: Casing Description

    1: overview 4 verint video intelligence solutions casing description the s1100w electronics are enclosed in a weather-tight cast aluminum module. All cable entries are mounted on the underside of the module to maintain its weatherproof properties. The front panel integrates one bicolor visual indica...

  • Page 17: System and Rf Planning

    Verint video intelligence solutions 5 system and rf planning to allow optimal configuration, you must properly plan your network, especially rf (radio frequency) and configuration layout..

  • Page 18: Frequency Bands and Channels

    2: system and rf planning 6 verint video intelligence solutions frequency bands and channels the s1100w supports communications in the following frequency bands, in north america and europe: 2.4 ghz ofdm, also known as 802.11g 4.9 ghz ofdm, a public safety band available in north america only 5 ghz ...

  • Page 19: 5 Ghz Band

    Verint video intelligence solutions 7 nextiva s1100w user guide the available channels are: 5 ghz band in the 5 ghz band, the number of available channels and sub-bands vary depending on the country of operation. Most european countries adhere to the dfs (dynamic frequency selection) and tpc (transm...

  • Page 20: Wireless Cells

    2: system and rf planning 8 verint video intelligence solutions wireless cells a wireless network is designed such that information can travel back and forth between two points without the need for wires. For the s1100w, this information consists of digitized video, audio, and ptz data sent to and f...

  • Page 21: System Planning

    Verint video intelligence solutions 9 nextiva s1100w user guide the supported authentication methods for wpa and wpa2 are: for more information about the tls (transport layer security) protocol, refer to rfc 2246 at http://www.Ietf.Org/rfc/rfc2246.Txt . The supported encryption methods are: wep aes-...

  • Page 22: Compatibility Issues

    2: system and rf planning 10 verint video intelligence solutions point-to-multipoint application a point-to-multipoint application is a wireless cell made up of an s3100 access point (the master) and several s1100w transmitters (the clients). Here is a typical point-to-multipoint system: for example...

  • Page 23

    Verint video intelligence solutions 11 nextiva s1100w user guide for example, consider the following setup: you should update the devices in the following order: 1. S1100w 1—you then lose contact with s1100w 1. 2. S1100w 2—you then lose contact with s1100w 2. 3. S3100 1—you can then reach all device...

  • Page 24: Tpc

    2: system and rf planning 12 verint video intelligence solutions the throughput for a 10 mhz channel is: the throughput for a 5 mhz channel is: the s1100w automatically adjusts the transmission speed with the current rf conditions. For the bit rate requirements of the edge devices to which the camer...

  • Page 25: Dfs

    Verint video intelligence solutions 13 nextiva s1100w user guide dfs to follow the dfs (dynamic frequency selection) regulations specified by etsi for the selected country, it is the master s3100 device that performs the tasks relative to frequency channel selection and radar detection. In other wor...

  • Page 26: Distance Limitations

    2: system and rf planning 14 verint video intelligence solutions distance limitations the distance limitations between devices are: the minimum distance between two devices is 3 feet (1 meter), regardless of the band or channel used. To avoid material damages, you must never power any two devices wh...

  • Page 27

    Verint video intelligence solutions 15 nextiva s1100w user guide this application can be illustrated this way, where the three cells are in the same location: 5 ghz band in north america and 2.4 ghz in the 2.4 ghz band in north america and europe, you can use the three independent channels (channels...

  • Page 28: 5 Ghz Band In Europe

    2: system and rf planning 16 verint video intelligence solutions this application can be illustrated this way, where the three cells are in the same location: 5 ghz band in europe the maximum number of colocated cells corresponds to the number of channels in the available frequency bands that can be...

  • Page 29

    Verint video intelligence solutions 17 nextiva s1100w user guide supported setups the following colocated systems are supported in the 5.40–5.725 ghz band: two access point applications, in which the transmitters from one system do not see the transmitters from the other cell. Both master devices se...

  • Page 30: Rf Planning

    2: system and rf planning 18 verint video intelligence solutions rf planning successful operation of a wireless link depends on proper rf path planning and antenna installation. You have to install the devices in such a way that there is a clear rf line of sight between the two antennas. Location ev...

  • Page 31: Antenna Requirements

    Verint video intelligence solutions 19 nextiva s1100w user guide a common problem encountered in the field and related to the 0.6 f1 clearance rule is building obstruction. The proposed visual path may just barely clear a building but the rf line of sight will not. In such a case, the signal will be...

  • Page 32: Interference

    2: system and rf planning 20 verint video intelligence solutions interference in most countries, the 2.4 ghz band is not regulated by a government agency; this absence of frequency coordination can result in interference between various systems. For instance, if a link with an rf line of sight is su...

  • Page 33: Configuring and

    Verint video intelligence solutions 21 configuring and installing the device the steps required to prepare your s1100w device for operation are: basic configuration physical installation in its final location alarm and audio configuration.

  • Page 34: Data

    3: configuring and installing the device 22 verint video intelligence solutions cable for power, video, and serial data the supplied cab9p cable assembly is used for video, power, and serial port connection. For the detailed pinout, see page 54. Serial port the s1100w integrates one multipurpose ser...

  • Page 35: Computer Requirements

    Verint video intelligence solutions 23 nextiva s1100w user guide to power an s1100w device: 1. In 12v dc, the red wire is for input and the black wire is for power ground. A. Twist together the black power wire of the cable and the wire with the dashed white lines of the supplied power supply. B. Tw...

  • Page 36: Point-to-Point Connection

    3: configuring and installing the device 24 verint video intelligence solutions to configure a wireless system: 1. In a lab, unpack the transmitter and the access point and place them on a table. 2. Connect the external antenna on the s3100 and optionally on the s1100w. Warning: to avoid material da...

  • Page 37

    Verint video intelligence solutions 25 nextiva s1100w user guide to perform a point-to-point connection: 1. Start sconfigurator. 2. In the units tab, discover the desired devices. The discovered devices appear in the units box. 3. Select the connections tab, then click add. The connection creator wi...

  • Page 38: Installing The Transmitter

    3: configuring and installing the device 26 verint video intelligence solutions installing the wireless system after configuring successfully your wireless system, you are ready to install it. To optimize your system radio performance, carefully review the site planning information presented in chap...

  • Page 39: Installing An Antenna

    Verint video intelligence solutions 27 nextiva s1100w user guide installing an antenna if you bought a high gain antenna, install it after the s1100w is in place. The antennas provided by verint video intelligence solutions are designed to be mounted on a mast or pole of 2–3 inch (5–7.5 centimeter) ...

  • Page 40

    3: configuring and installing the device 28 verint video intelligence solutions for example, here is an s1100w transmitter connected to a ptz camera in an rs-422 2-wire context: for a two-wire, half-duplex rs-485 connection: 1. Use the following wiring scheme: 2. Set the line driver to the 485h-f va...

  • Page 41: Configuring The I/os

    Verint video intelligence solutions 29 nextiva s1100w user guide the numbering of the pins on the db-9 connector is: configuring the i/os to program alarms (or events) or use the audio features of the s1100w device, you need the cab8p cable assembly. For detailed pinout information, see page 55. The...

  • Page 42: Alarms

    3: configuring and installing the device 30 verint video intelligence solutions here is a typical ptt application in a point-to-point context: the s1100w device supports the line-in input type. With sconfigurator, ensure that the input type in the audio tab reflects this value. Regardless of the tra...

  • Page 43: Updating The Firmware

    Verint video intelligence solutions 31 nextiva s1100w user guide updating the firmware you can update the firmware of the s1100w devices with the sconfigurator utility or a video management software; for the detailed procedure, refer to the documentation of the software. The latest firmware files ar...

  • Page 44: Red/blue Display

    3: configuring and installing the device 32 verint video intelligence solutions red/blue display if an s1100w transmitter currently streaming video to a management software loses its connection to a camera, the corresponding display tile in the software will present an error sequence, typically a ha...

  • Page 45

    Verint video intelligence solutions 33 nextiva s1100w user guide the following power-up conditions on the system status led are abnormal: led not lit—check the power supply and cabling. If power is available and the led stays off, call verint video intelligence solutions customer service for assista...

  • Page 46

    34 verint video intelligence solutions.

  • Page 47: Setting Parameters With

    Verint video intelligence solutions 35 setting parameters with the cli the s1100w devices come with a simple command line interface (cli) for configuration purposes. The cli is hierarchically organized, with menus, sub-menus, and individual options representing configuration parameters. Only the par...

  • Page 48: Getting Started

    4: setting parameters with the cli 36 verint video intelligence solutions getting started you can access the cli with: a serial connection and the sconfigurator console a network connection and the telnet utility to access the cli with the sconfigurator console: 1. Connect the s1100w device to a com...

  • Page 49: Serial Port

    Verint video intelligence solutions 37 nextiva s1100w user guide 7. To work through the cli menu structure, follow these guidelines: to execute a command or open a menu, type in the corresponding letter or number, then press enter. To return to the previous menu, enter p. 8. To end the cli work sess...

  • Page 50

    4: setting parameters with the cli 38 verint video intelligence solutions bit rate the bit rate represents the data rate at which the target product operates. Possible values range from 1200 bps to 230,400 bps. Parity the serial equipment may have a parity of odd or even. It may also not have parity...

  • Page 51: Access Management

    Verint video intelligence solutions 39 nextiva s1100w user guide access management the access management menu takes care of user accounts (user names and passwords) and device security. User accounts the user accounts menu enables you to protect the configuration of the device by restricting its acc...

  • Page 52: Network

    4: setting parameters with the cli 40 verint video intelligence solutions telnet session by default, you can use telnet to access the cli of your device. To improve the security of your system, you may prohibit such an access. In this case, the cli will only be accessible through a serial connection...

  • Page 53: Wireless Communication

    Verint video intelligence solutions 41 nextiva s1100w user guide subnet mask the subnet mask is the binary configuration specifying in which subnet the ip address of the device belongs. A subnet is a portion of a network that shares a common address component. On tcp/ip networks, a subnet is defined...

  • Page 54: Basic Parameters

    4: setting parameters with the cli 42 verint video intelligence solutions the parameters for the 802.11 protocol are: basic parameters passkey (spcf only) the wireless passkey is a unique case-sensitive identifier enabling secure and encrypted rf communication between the s1100w device and its acces...

  • Page 55

    Verint video intelligence solutions 43 nextiva s1100w user guide wpa authentication method (802.11 only) the s1100w in 802.11 mode supports the following authentication mechanisms: wpa-psk (wi-fi protected access version 1 in pre-shared key mode, also known as personal mode) wpa2-psk (wpa version 2,...

  • Page 56

    4: setting parameters with the cli 44 verint video intelligence solutions wpa private key passphrase (802.11 only) the private key passphrase is a case-sensitive identifier (from 0 to 63 characters) used to secure the access to an 802.11 certificate. Wpa negotiation timeout (802.11 only) the negotia...

  • Page 57

    Verint video intelligence solutions 45 nextiva s1100w user guide in a 4.9 ghz band context, the list of channels varies depending on the chosen bandwidth. For the list of channels, see page 7; for the channel bandwidth parameter, see next. Channel bandwidth in the 4.9 ghz band, the bandwidth can be ...

  • Page 58: Advanced Parameters

    4: setting parameters with the cli 46 verint video intelligence solutions advanced parameters the advanced wireless setup menu contains specialized rf features. The parameter set varies depending on the mac mode (spcf or 802.11). The parameters for spcf are: the parameter for the 802.11 protocol are...

  • Page 59: System Status

    Verint video intelligence solutions 47 nextiva s1100w user guide minimum margin (spcf only) the minimum margin is used when the transmission bit rate is set to auto (see page 45). It represents the difference in db between the actual signal received by the device and the minimum signal required by a...

  • Page 60: Advanced

    4: setting parameters with the cli 48 verint video intelligence solutions advanced the advanced menu holds a series of advanced setups mainly used by verint video intelligence solutions technical support. Some of these parameters are available through sconfigurator or a video management software. Id...

  • Page 61: Conducting Site Surveys

    Verint video intelligence solutions 49 nextiva s1100w user guide conducting site surveys the s1100w device allows you to perform site surveys on your rf network. A site survey scans all frequency channels, evaluate the interference level in each channel, and allows you to choose the channel with the...

  • Page 62: Reboot System

    4: setting parameters with the cli 50 verint video intelligence solutions reboot system the reboot system command, located in the main menu, performs a soft boot on the s1100w. A system reboot clears all unsaved changes in the cli and returns to your preset configuration..

  • Page 63: Factory Default

    Verint video intelligence solutions 51 factory default configuration.

  • Page 64

    A: factory default configuration 52 verint video intelligence solutions the s1100w is programmed at the factory with the following configuration: type configuration serial port bit rate: 4800 bauds data bits: 8 parity: none stop bit: 1 line driver: auto-detected rs-422/485 operating mode: rs422 4 wi...

  • Page 65: Cable Connections

    Verint video intelligence solutions 53 cable connections the wireless devices use the following two cables: cab9p—power, video, and serial data communication cab8p—audio and alarms note: to determine the rx and tx pins of your equipment, see appendix d on page 59..

  • Page 66: Cab9P

    B: cable connections 54 verint video intelligence solutions cab9p the cab9p cable supplied with the wireless devices is used for power, video, and serial communication (that is, ptz data with the rs-422/485 protocol, or rs-232 communication with the db-9 connector). The mating side view of the cable...

  • Page 67: Cab8P

    Verint video intelligence solutions 55 nextiva s1100w user guide based on the pinout, the wiring scheme for an rs-232 connection to a computer is: cab8p the cab8p cable is used for audio and alarms. The mating side view of the cable is: cable computer signal name wire pair wire color signal name cts...

  • Page 68

    B: cable connections 56 verint video intelligence solutions here is its pinout: where: the other wire of the twisted pair is enclosed in square brackets..

  • Page 69: Dhcp Support and

    Verint video intelligence solutions 57 dhcp support and apipa dhcp (dynamic host configuration protocol) allows devices and computers connected to a network to automatically get a valid ip configuration from a dedicated server. The apipa (automatic private ip addressing) scheme, available on the win...

  • Page 70

    C: dhcp support and apipa 58 verint video intelligence solutions at startup, an edge device searches for a valid ip network configuration. The device requires this configuration prior to starting its functions. The network configuration for nextiva devices consists of: an ip address a subnet mask a ...

  • Page 71: Dte and Dce

    Verint video intelligence solutions 59 dte and dce connections before connecting a nextiva edge device to other rs-232 serial equipment, you need to determine if they are dte (data terminal equipment) or dce (data communication equipment). Here are examples of both equipment types: dce—nextiva edge ...

  • Page 72

    D: dte and dce connections 60 verint video intelligence solutions in the following descriptions: voltage is measured when no data is transferred on the rx and tx pins. -x volts represents a negative voltage value. Data terminal equipment dte modules have the following electrical-level setup: data co...

  • Page 73

    Verint video intelligence solutions 61 nextiva s1100w user guide connecting dte and dce when connecting two modules of the same type, you have to cross the data wires to create proper communication. On the other hand, when connecting a dte with a dce, a straight cable is required. Dce dce dte dte dt...

  • Page 74

    62 verint video intelligence solutions.

  • Page 75: Surge Protection

    Verint video intelligence solutions 63 surge protection voltage and current surges can be induced by lightning strikes or power line transients. In the real world, under the right circumstances, these surges can reach sufficiently high levels to damage almost any electronic equipment. Therefore you ...

  • Page 76

    E: surge protection 64 verint video intelligence solutions the s1100w provides basic surge protection on all electrical lines. If you are installing the equipment in a lightning prone or heavy lightning environment, or in a site where large ac mains power fluctuations are a common occurrence, verint...

  • Page 77: Separation Between

    Verint video intelligence solutions 65 separation between devices using adjacent channels wireless interference can occur between wireless cells using adjacent frequency channels (for example, channels 149 and 153 in the 5 ghz band). Therefore, it is preferable to avoid using adjacent channels. Howe...

  • Page 78: Performing A Site Survey

    F: separation between devices using adjacent channels 66 verint video intelligence solutions if using adjacent frequency channels in a non-dfs environment, you should respect guidelines relative to the minimum separation between device antennas, to avoid interference. To reduce radio interference po...

  • Page 79

    Verint video intelligence solutions 67 nextiva s1100w user guide to calculate the emission margin between two adjacent wireless cells: 1. Open sconfigurator, then go to the units tab. 2. Select the master device in the wireless cell you are adding, then click telnet. 3. From the main menu of the com...

  • Page 80

    F: separation between devices using adjacent channels 68 verint video intelligence solutions 6. When the survey is complete, visualize the report. For example: this report provides the signal levels between device a1 and the other five devices in the network. The lowest signal in cell a is -75 (s1) ...

  • Page 81: Minimum Distances

    Verint video intelligence solutions 69 nextiva s1100w user guide minimum distances to respect the 25 db margin between two adjacent channels, in addition to performing a site survey, you can use guidelines relative to minimum distances between the wireless devices. By respecting them, you can assume...

  • Page 82

    F: separation between devices using adjacent channels 70 verint video intelligence solutions the following deployment scenarios respect these limitations: using only 5 ghz channels, all on the same side of a building: notice that the devices using the adjacent channels 52 and 56 are separated by the...

  • Page 83

    Verint video intelligence solutions 71 nextiva s1100w user guide using 5 ghz and 2.4 ghz channels, all on the same side of a building: the devices using the adjacent channels 6 and 11 in the 2.4 ghz are separated by the prescribed 56 feet (17m). 5.8 ghz 165 5.3 ghz 56 5.8 ghz 157 5.3 ghz 64 5.8 ghz ...

  • Page 84

    72 verint video intelligence solutions.

  • Page 85: Dfs and False Radar

    Verint video intelligence solutions 73 dfs and false radar detection nextiva wireless devices operating in the european union must adhere to the dynamic frequency selection (dfs) standard; this standard forces any rf transmitter to change frequency channels if radar activity is detected on the curre...

  • Page 86

    G: dfs and false radar detection 74 verint video intelligence solutions to avoid false radar detection caused by an adjacent channel, the signal level of an potential interfering device on the first adjacent channel must not exceed -50 db, -36 db on the second channel, and -32 db on the third channe...

  • Page 87: S1100W Technical

    Verint video intelligence solutions 75 s1100w technical specifications.

  • Page 88

    S1100w technical specifications 76 verint video intelligence solutions here are the s1100w technical specifications: network rf interface proprietary spcf, 802.11 modulation ofdm encryption 128-bit aes data rate (max. Burst rate) 6, 9, 12, 18, 24, 36, 48, and 54 mbps protocols transport: rtp/ip, udp...

  • Page 89: Glossary

    Verint video intelligence solutions 77 glossary this glossary is common to the nextiva line of edge device products..

  • Page 90

    Glossary 78 verint video intelligence solutions access point a communication hub for connecting wireless edge devices (s1100w) to a wired lan. The nextiva access point is the s3100 product. Aes (advanced encryption standard) an encryption standard used in the wpa2 authentication method. Apipa (autom...

  • Page 91

    Verint video intelligence solutions 79 nextiva s1100w user guide firmware software stored in read-only memory (rom) or programmable rom (prom), therefore becoming a permanent part of a computing device. Ip (internet protocol) the network layer for the tcp/ip protocol suite widely used on ethernet ne...

  • Page 92

    Glossary 80 verint video intelligence solutions ptl (push-to-listen) in a two-way system, the communication mode in which the listener must push a button while listening. Ptt (push-to-talk) in a two-way system, the communication mode in which the talker must push a button while talking. Ptz camera (...

  • Page 93

    Verint video intelligence solutions 81 nextiva s1100w user guide s1900e-vicon the board holding the s1900e compact ip technology, to be included into vicon surveyorvft dome cameras. S2500e the mpeg-4-compliant professional ip camera integrating a video sensor and an ethernet encoder in the same comp...

  • Page 94

    Glossary 82 verint video intelligence solutions wep (wired equivalent privacy) a security protocol for wireless local area networks (wlans) defined in the 802.11b standard. It is designed to afford wireless networks the same level of protection as a comparable wired network. Wireless bridge a link b...

  • Page 95: Index

    Verint video intelligence solutions 83 index numerics 0.6 f1 18 2.4 ghz frequency band. See frequency band. 24v ac power connection warning iii 4.9 ghz frequency band. See frequency band. 5 ghz frequency band. See frequency band. 802.11 8 , 42 – 47 802.11a. See frequency band. 802.11g. See frequency...

  • Page 96

    Index 84 verint video intelligence solutions configuration alarm 29 , 30 audio 29 – 30 camera data port 2 default 31 , 49 , 51 device 23 – 24 i/o 29 – 30 order, in the wireless cell 10 connection to a camera, losing 32 dce/dte 59 point-to-point 24 power iii , 22 rs-232 28 serial 22 , 27 – 29 connect...

  • Page 97

    Nextiva s1100w user guide verint video intelligence solutions 85 interference, rf 20 , 65 ip address apipa 57 duplicate 23 setting 23 , 40 temporary 57 k key. See passkey. L led, status 32 licensed band. See frequency band. Limitations distance 13 , 69 – 71 europe 12 – 13 , 16 – 17 line interface, e...

  • Page 98

    Index 86 verint video intelligence solutions requirements antenna 19 computer 23 power 3 video bit rate 12 reserved vsip ports 48 reset to factory default 31 , 49 , 51 resolution, video 3 rf (radio frequency) channel. See frequency channel. Contact between two masters 16 exposure considerations 20 g...

  • Page 99

    Nextiva s1100w user guide verint video intelligence solutions 87 wireless cell 8 – 16 wireless communication parameters 41 – 47 wireless frequency plan 7 wiring scheme alarm 55 audio 55 rs-232 54 – 55 rs-422/485 27 – 28 wpa (wi-fi protected access) 8 , 43 wpa2 (wi-fi protected access version 2) 8 , ...

  • Page 100

    88 verint video intelligence solutions.

  • Page 101: Compliance

    Verint video intelligence solutions 89 compliance.

  • Page 102

    Compliance 90 verint video intelligence solutions to reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the effective isotropic radiated power (eirp) is not more than that required for successful communication. Note: the s1100w devices require ...

  • Page 103

    Verint video intelligence solutions 91 nextiva s1100w user guide italia l'uso di questo apparato in italia è regolamentato da: d.Lgs 1.8.2003, n.259, articoli 104 (attività soggette ad autorizzazione generale) e 105 (libero uso), per uso privato; d.M. 28.5.03, per la fornitura al pubblico dell'acces...

  • Page 104

    Compliance 92 verint video intelligence solutions turkey declaration of conformity manufacturer: verint systems inc. 1800 berlier laval, québec h7l 4s4 canada declares under sole responsibility that the product: product name: wireless video transmitter model number: s1100w to which this declaration ...

  • Page 105

    Verint video intelligence solutions 93 nextiva s1100w user guide rohs declaration of compliance june 14th, 2006 verint believes in the importance of conducting our business in a manner that will help protect the environment as well as our employees, customers, and the public. To that end, we are com...

  • Page 106

    94 verint video intelligence solutions.

  • Page 107: Americas

    Americas emea apac info@verint.Com marketing.Emea@verint.Com marketing.Apac@verint.Com www.Verint.Com/videosolutions www.Verint.Com/videosolutions www.Verint.Com/videosolutions.