Summary of Lavatube
Page 1
User guide.
Page 2
Welcome to the volcano fine electronic cigarettes® family and thank you for your purchase! Here you will find all the information that you need to get your kit up and running. If after reading through this you still need some help, we welcome you to visit our website for more useful videos, tips, an...
Page 3
Device anatomy battery compartment this is where the battery is housed. Power - activation button this button powers the device on/off and activates the unit during use. Led screen this is the led screen for displaying power features. A b c d a b c d tube tank this is the heating element / eliquid w...
Page 4
Features 2 power modes: the device can be set to either average voltage, or vrms ( recommended setting ). Within these modes the device can be set to either variable voltage or variable watage. 1 2 device memory: all device settings are stored in internal memory. The lavatube® remembers the output s...
Page 5
Installing / replacing battery - step 1 1 unscrew and remove the lavatube head unit. 1.
Page 6
Installing / replacing battery - step 2 2 install an aw imr high drain rechargeable limn battery into the lavatube. 2.
Page 7
Installing / replacing battery - step 3 3 reassemble the lavatube® by screwing the battery compartment back onto the head unit. 3.
Page 8
Turning device on, checking voltage and ohms: - step 1 1 to turn the device on/off, click the activation button 5 times rapidly ( approximately a half of a second in-between clicks ) 1.
Page 9
2 to check the battery level, the lavatube® is capable of reading and displaying the current voltage the battery is outputting on it’s own. To do this, simply press and hold the minus button for approximately 5 seconds. The display will briefly show the battery voltage between a range of 4.2v ( full...
Page 10
3 to check the ohms of the heating element attached, press and hold the plus button for approximately 5 seconds. The screen will briefly show the heating elements ohm resistance level before reverting back to the general power settings screen. Turning device on, checking voltage and ohms: - step 3 3.
Page 11
1 press and hold both the plus and minus buttons at the same time for approximately 10 seconds. The screen will change to either 3v or 3w depending on the current setting. Repeat to select a different mode. Switching between voltage and wattage modes: 2 3.
Page 12
1 press and hold either the negative or positive button for approximately 20-25 seconds. The screen will change to either no1 (average voltage) or no2 (vrms) depending on the current setting. Repeat to select a different mode. Switching between average and vrms modes: 2 3.
Page 13
Average voltage and vrms modes: the initial setting on your lavatube® v2.5 device will vary from average voltage to vrms mode in either variable voltage or variable wattage. When in average voltage mode (no1) the power going to the heating elements will be a little higher than in vrms (no2) mode. Fo...
Page 14
A 2 the lavatube® v2.5 is an advanced electronic device that must be maintained properly to ensure proper function. By following these cleaning instructions, you will ensure that your unit is always in top working order. Preventive cleaning and maintenance: clean the heating element connection (510 ...
Page 15
B preventive cleaning and maintenance ( continued ): next, wipe the connection dry with a different paper towel or the other side of the q-tip. Recommended cleaning and upkeep.
Page 16
A 2 with the device disassembled, clean the threading of both the head unit and the battery compartment. Using a green scouring pad, or similar cleaning tool, scrub the threads with light pressure. Then lightly wipe off any dirt and grime that may have came off the threads with isopropyl alcohol. 2 ...
Page 17
Recommended cleaning and upkeep 2 when using the device, make sure that any excessive eliquid spillage or build up is cleaned and wiped from the unit whenever possible to prevent it from seeping into the device, and causing damage. 3 preventive cleaning and maintenance ( continued ):.
Page 18
A 2 advanced cleaning and maintenance: with the device disassembled locate the spring at the bottom of the battery compartment. Using a long needle nose pliers or a straightened paper clip with a open loop on one end, grab and remove the spring. With the spring removed, take a scouring pad that has ...
Page 19
B advanced cleaning and maintenance: while waiting for the battery compartment to dry, take the spring and brush it with the scouring pad along the length of the wire of the spring. Rinse the spring with isopropyl alcohol and let stand to air dry. Recommended cleaning and upkeep.
Page 20
C advanced cleaning and maintenance: after both the spring and tube are dry, push the spring back into place using a marker or other tool that can provide even pressure to the spring. Make sure that the spring is seated all the way around the bottom of the tube, and that it is seated upright and not...
Page 21
Battery handling battery handling (continued) be aware of and understand that there are serious dangers of handling li-ion batteries regardless of what you may have heard from others. Charge your batteries on a fire proof or flame retardant surface such as concrete, natural stone, or tile using only...
Page 22
Warranty warranty (exclusions) 1 year limited warranty information volcano fine electronic cigarettes® warrants this device against defects in materials and workmanship under normal use for a period of one (1) year from the date of retail purchase by the original end-user purchaser. If a physical de...
Page 23
Environment support informal handling of waste electrical and electronic equipment (weee) has potential negative effects on the environment and human health as a result of the presence of hazardous substances in electrical andelectronic equipment. The crossed out waste bin symbol indicates that this...