Version: 2.0 this manual contains important laser system safety and operation information. Read and understand all instructions prior to powering on laser unit the first time, to avoid laser eye injury and to avoid breaking the law. Keep this manual in a safe place for future reference..
User manual 1 warning data lasers can be hazardous and have unique safety considerations. Permanent eye injury and blindness is possible if lasers are used incorrectly. Pay close attention to each safety remark and warning statement in the user manual. Read all instructions carefully before operatin...
User manual 2 laser safety warnings caution avoid direct eye contact with laser 了 light. Never intentionally expose your eyes or others to direct laser radiation. Caution this laser product can potentially cause instant eye injury or blindness if laser light directly strikes the eyes. Caution it is ...
User manual 3 laser safety and operating instructions stop and read all laser safety data laser light is different from any other light source witch you may be familiar. The light from this product can potentially cause eyes injury if not set up and used properly. Laser light is thousands of times m...
User manual 4 z after set up, and prior to public use test laser to ensure proper function. Do not use if any defect is detected. Do not use if laser emits only one or two laser beams rather than dozens/hundreds, as this could indicate damage to the diffraction grating optic, and could allow emissio...
User manual 5 laser safety label reproductions this is only one laser aperture on this product. The label indicates the laser beam output aperture. Caution – class 3b laser radiation, when open, avoid exposure to beam laser radioation avoid exposure to beam class 3b laser product. Laser emission dat...
User manual 6 laser compliance statement this laser product complies with en/iec 60825-1 ed 2,2007-03. General safety instructions every person involved with installation and maintenance of this device have to z be qualified. Z follow the instructions of this manual. This device has left out premise...
User manual 7 z always disconnect from the mains, when the devise is not in use or before cleaning it. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord. Z it is essential to connect the yellow/green conductor to earth. Z the electric connection, repairs and s...
User manual 8 before operation unpacking instructions caution! Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspecti...
User manual 9 the unit is supplied with a power plug appropriate to its voltage and destination. Should any other connections be required they must be carried out with the following configuration. Dmx-512 connection between fixtures the fixture is equipped with 2-pin xlr sockets for dmx input and ou...
User manual 10 building a serial dmx-chain z if you are using the standard dmx-controllers, you can connect the dmx-output of the controller directly with the dmx-input of the first fixture in the dmx-chain. If you wish to connect dmx-controllers with other xlr-outputs, you need to use adapter cable...
User manual 11 safety cable. Items appropriate for safe and effective mounting are easily sourced from your lighting vendor. International laser safety regulations require that lasers must be operated in the fashion illustrated below, with a minimum of 3 meters (9.8 ft) of vertical separation betwee...
User manual 12 z make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing. Z the operator has to make sure that safety-relating and machine-technical installations are approved by an expert before taking into operation for the first time ...
User manual 13 front panel no name function 1 laser output laser output aperture. 2 power main power indicated led. Red is on. 3 music synchronize to detected music signal 4 hanging bracket with 2 knobs on both sides to fasten the unit and a mounting hole to fix a mounting hook. Rear panel.
User manual 14 important for your own safely and full laser safety regulation, we do strongly recommend you to take this optional switch! No name function 5 mains input with socket and integrated fuse holder 6 switch switch on and off the power 7 dmx input 3pin male xlr port, using for dmx 8 dmx out...
User manual 15 control & function z regular breaks during operation are essential to maximize the life of this device as it is not designed for continual use. Z do not switch the unit on and off in short time intervals z always unplug the unit when it is not used for a longer time. Or before replaci...
User manual 16 operation dispaly stand alone mode preprogram effect aus auto show with slow effect auf which is the random auto show. Sos sound show with slow effect sof which is the random sound show attention in preprogrammed standalone music show mode, the laser beam will be blank-out in 3 second...
User manual 17 z attention in dmx mode, once the dmx cable is connected with laser and dmx controller, the dmx led in front panel of laser will be on. Slave mode z press func to enter mode selection z till to led panel shows sla z press enter to confirm setting the laser is working in slave mode. Co...
User manual 18 z with help of down button, the laser scanned world in y direction could be reversed, as the graphic as below. Z attention beside of led programmed mirror reverse setting, the laser scanned world could be set by ilda control panel. Ilda control mode z this unit has the ilda db25 port,...
User manual 19 104-055 3 group patterns 156-207 4 group patterns 208-255 5 group patterns ch 3 pattern 000-255 every 16 for 1 group, total 80 patterns. Ch 4 color 000-007 original 008-015 red 016-023 green 024-031 yellow 032-039 blue 040-047 purple 048-055 light blue 056-063 white 064-111 color roll...
User manual 20 170-209 zooming out 210-255 alternately zooming ch 7 zoom 000-255 fast to slow ch 8 y axis rolling 000-127 0 -359 degree fixed y axis rolled 128-191 clockwise rolling 192-255 anticlockwise rolling ch 9 roll 0-255 fast to slow ch 10 x axis rolling 000-127 0 -359 degree fixed x axis rol...
User manual 21 pattern list dmx 1 tunnel 2 pole 3 curve 4 line 5 graphic 000-015 016-031 032-047 048-063 064-079 080-095 096-111 112-127 128-143 144-159 160-175 176-191 192-207 208-223 224-239 240-255.
User manual 22 specifications mains input: fuse: total power: x/y axis beam angle: control mode: laser power: laser classification: laser safety standard: condition temperature: dmx connections: dmx channels measurement: n weight: ac100~240v, 50/60hz 250v 1a slow blow (20mm glass) 30w ±25° auto, sou...
