Summary of INS-801
Page 1
5-port 10/100base-tx industrial switch (ins-801 / ins-801w) user’s guide.
Page 2
Copyright all rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, whether electronic, mechanical, photo copying, recording or otherwise, without the prior written permission of the publisher. Fcc warning this equipm...
Page 3
T a b l e o f c o n t e n t s about this guide............................................................ 4 t erms /u sage ....................................................................... 4 introduction ................................................................... 4 i ndustrial e thern...
Page 4
4 a b o u t t h i s g u i d e the ins-801/ins-801w industrial series switch is a hardened, 5-port ethernet switch with redundant dc power inputs – designed to provide a reliable and economical solution for your industrial ethernet environment. With its dry contact smart alarm, the ins-801/801w can i...
Page 5
5 industrial ethernet technology the growing importance of ethernet has extended to the factory floor and industrial environments, where things have become too harsh for typical commercial-grade networking equipment. Volktek has created an industrial series of switches and interconnecting devices sp...
Page 6
6 features the switch was designed for easy installation and high performance in an industrial environment where vibration, shock, heat, and rf interference may be commonplace. The switch was specifically designed to be small and compact for easy din-rail mounting and it can be installed where space...
Page 7
7 o rugged, hardened ip30 case o vibration/shock operational o power terminal block o wide voltage range: 9-48v o dip-switch to enable or disable alarm functions o power input polarity protection function o under-power and over-power detection function o wide operating temp.: -40°c ~ 70°c for the in...
Page 8
8 your local reseller for replacement. Layout of the ins-801/801w front view of switch 8 9 10 1. Alarm led 2. Redundant power led 3. Primary power led 4. Tx ports (5) 5. Tx port 100mbps led 6. Tx port lnk/act led 1 2 3 4 5 6.
Page 9
9 top view of switch back view of switch din rail bracket screws grounding screw terminal block for power input (pwr/rps), and alarm dry contact dip-switches.
Page 10
10 din-rail mounting of the ins-801/801w the aluminum din-rail attachment plate should already be affixed to the back panel of the switch. If you need to attach the din-rail plate, assure that the stiff metal spring is situated towards the top. Attaching the switch to the din-rail is easy: just alig...
Page 11
11 from the switch. • visually inspect the dc power jack and make sure that it is fully secured to the power adapter. • make sure that there is proper heat dissipation from and adequate ventilation around the switch. Do not place heavy objects on the switch. Grounding the ins-801 industrial switch w...
Page 12
12 dc powered switch: power is supplied through an external dc power source. Check the technical specification section for information about the dc power input voltage. Since the switch does not include a power switch, plugging its power adapter into a power outlet will immediately power it on. To t...
Page 13
13 procedure for connecting dc power: for shipping, the removable green contact block may be detached from the six-pin terminal contact point. It may be easier to attach the dc wires to the green contact block if it has first been unplugged from the terminal contact point on the switch. A. On the po...
Page 14
14 led indicators switch status leds besides led indicators for the 10/100basetx ports, the switch has the following led status indicators: power indicator (pwr) this indicator lights green when the switch is receiving power from primary power supply. Otherwise, it is off. Redundant power supply (rp...
Page 15
15 connection point located on the green power contact block on the top panel. For detailed instructions on how to connect the alarm contact power wires to the two alm contacts of the 6-contact terminal block connector, see the procedure for connecting dc power in the section above (it is the same p...
Page 16
16 figure below shows the dip-switch control: dip-switch to the on position to manually enable the alarm function for the port. Default is off. Dip 8 (qos) controls the qos function on port 1 of the switch. Default is on. The following is the recommended procedure for configuring and setting dip-swi...
Page 17
17 by both devices. This helps make the switch a plug-and- play device. The switch’s rj-45 ports support full or half duplex, depending on which transmission speed is supported by the attached device. Switching, filtering, and forwarding packets entering the ins-801 switch with source and destinatio...
Page 18
18 if the connected device does not support auto-negotiation or has auto-negotiation disabled, an auto-sensing process is initiated to select the speed and set the duplex mode to half-duplex. T e c h n i c a l s p e c i f i c at i o n s general standards ieee 802.3 ieee 802.3u & ieee 802.3x connecto...
Page 19
19 performance transmission method: store-and-forward, with ieee802.3x full duplex, non-blocking flow control. Packet filtering / forwarding rate: 10mbps ethernet: 14,880/pps 100mbps fast ethernet: 148,800/pps mac address learning: update automatically a p p e n d i x rj-45 pin specifications the rj...
Page 20
20 the standard cable, rj-45 pin placement the standard rj-45 receptacle/connector volktek corporation 4f, no. 192 lian-cheng road chung-ho, taipei 235, taiwan roc tel: +886 (2) 8242-1000 fax: +886 (2) 8242-3333 iso 9001 certified.
Page 21
21 french distributor predata© http://www.Trade.Predata.Fr tel: + 33 (0) 3 26 22 14 14 fax: + 33 (0) 3 26 22 14 13.