1. DL manuals
  2. VOLKTEK
  3. Media Converter
  4. NWT-707
  5. User Manual

VOLKTEK NWT-707 User Manual

Manual is about: 10Base-T to 10Base-FL Converter (Multi-mode & Single Mode)

Summary of NWT-707

  • Page 1

    10base-t to 10base-fl converter (multi-mode & single mode) user’s manual nwt-707.

  • Page 2

    Copyright all rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photo copying, recording or otherwise, without the prior written permission of the publisher. Fcc warning this equip...

  • Page 3

    Table of contents 1 introduction .................................................................. 1 about this guide ........................................................... 1 welcome................................................................... 1 purpose .....................................

  • Page 4

    Installing the converter .......................................... 20 rear view of chassis and specifications................ 21 appendix d .................................................................... 22 application diagram..................................................... 22 application...

  • Page 5

    10base-t to 10base-fl converter 1 1 introduction about this guide welcome thank you for choosing the 10base-t to 10base-fl media converter. This device integrates ethernet copper and fiber segments in a highly flexible package. Purpose this guide discusses how to install and configure your 10base-t ...

  • Page 6

    10base-t to 10base-fl converter 2 features • complies with 802.3 10base-t/fl standard • mdi/mdi-x push button selection for rj-45 port connection • support st or sc fiber connector • extend fiber distance up to 12km with single mode fiber • compatible with other 10base-t/fl and 10/100 devices • stat...

  • Page 7

    10base-t to 10base-fl converter 3 specifications standard: ieee 802.3u connector: 1 rj-45, 1 st for multi-mode or sc for single mode max. Distance: twisted pair: 100m (330ft) multi-mode: 2km (6600feet) single mode: 12km (39600feet) unit leds: power - illuminated for normal operation port leds: link ...

  • Page 8

    10base-t to 10base-fl converter 4 package contents the 10base-t to 10base-fl converter package should include: • one converter • one ac adapter (for external power supply) • four pieces self-adhesive pads • one user’s manual go to installing your converter.

  • Page 9

    10base-t to 10base-fl converter 5 2 hardware description product overview the converter is primarily designed for network or data installations that require the migration of cable media between conventional coppers based wiring to fiber based installations. These converters have been specifically de...

  • Page 10

    10base-t to 10base-fl converter 6 front panel view with sc and rj-45 connectors front panel view with st and rj-45 connectors.

  • Page 11

    10base-t to 10base-fl converter 7 3 installation installing your converter in this chapter, we will take a look at how to install converters within its operating environment. First, it is important to unpack the converter and ensure that all the components listed in package contents are present. • l...

  • Page 12

    10base-t to 10base-fl converter 8 location the location selected for installing the converter may greatly affect its performance. When selecting a site, we recommend considering the following rules: 1. Install the converter in a fairly cool and dry place. See technical specifications for the accepta...

  • Page 13

    10base-t to 10base-fl converter 9 mdi/mdi-x connection the mdi / mdi-x function alleviates the worry of cable type configuration used for connecting the converter with a 10base-t device. Simply follow the chart below when connecting the converter, and use the push button to select mdi or mdi-x accor...

  • Page 14

    10base-t to 10base-fl converter 10 install the converter this converter utilizes ports with fiber and copper port connectors functioning under the fast ethernet protocol. 10base-t port the 10base-t port supports network speed of 10mbps, and is designed to operate in half-duplex transfer mode only. T...

  • Page 15

    10base-t to 10base-fl converter 11 desktop installation follow the instructions listed below to install the converter onto a desktop location. 1. Locate the converter in a clean, flat and safe position that has easy access to ac power. 2. Affix the four (4) self-adhesive rubber pads to the underside...

  • Page 16

    10base-t to 10base-fl converter 12 powering on unit the converter uses external power supply 12v dc @ 0.8a 50~60 hz. 1. Insert the power cable plug directly into the receptacle located at the back of the device. 2. Plug the power adapter into an available socket. 3. Check the front-panel leds as the...

  • Page 17

    10base-t to 10base-fl converter 13 connecting fiber cable when connecting fiber cable to a 10base-fl port on the converter, be sure the correct type - st or sc - connector is used. Follow the steps below to properly connect fiber cable: 1. Remove and keep the fiber port's rubber cover. When not conn...

  • Page 18

    10base-t to 10base-fl converter 14 connecting copper cable 1. Insert one end of category 5 twisted pair cable into an available rj-45 port on the converter and the other end into the port of the network node. 2. Check the corresponding port led on the converter to make sure that the connection is va...

  • Page 19

    10base-t to 10base-fl converter 15 4 led indicators led table this converter has led indicators located at the front of the device. The leds have been designed to give easy at- a-glance network status, and provides ‘real-time’ connectivity information. Please see below for an interpretation of their...

  • Page 20

    10base-t to 10base-fl converter 16 appendix a cables the following are some recommendations as to what you should and should not do when installing cables. Remember - cables are the deciding factor in network performance. 24 m m 6mm try to maintain a bend rad ius o f (min.) 4x the diameter of the ca...

  • Page 21

    10base-t to 10base-fl converter 17 appendix b about rj-45 cables when connecting your network devices, use standard category 3 eight-way cables for 10base-t configurations and category 5 cable for 100base-tx. The pin assignments are as follows: pin 1 td+ pair 2 white/orange pin 2 td- pair 2 orange/w...

  • Page 22

    10base-t to 10base-fl converter 18 appendix c mini converter chassis the chassis was developed to accommodate just one media converter. The chassis provides protection for converter units and an option of ac or dc power supplies. Now, network designers can plan their ethernet, fast ethernet, atm, or...

  • Page 23

    10base-t to 10base-fl converter 19 affixing brackets we have supplied 2 special brackets that easily attaches to the converter. This allows for the secure placement of the converter into the chassis. It also seals off the front of chassis and allows it to function correctly. Step 1 using a phillips ...

  • Page 24

    10base-t to 10base-fl converter 20 installing the converter once the converter has been attached to the bracket, it can be installed into the chassis. Special care must be taken to ensure the correct mating of the power connector. Align the converter so that it fits between the upper and lower guide...

  • Page 25

    10base-t to 10base-fl converter 21 rear view of chassis and specifications rear view of chassis with ac power supply power: 100 - 240v ac (optional 12v adapter) dimensions: 109 x 174 x 44.3 mm (l x w x h) rear view of chassis with dc power supply power: -48v dc (optional 12v adapter) dimensions: 109...

  • Page 26

    10base-t to 10base-fl converter 22 appendix d application diagram to effectively expanding an ethernet network, position two converters back-to-back as illustrated. Application diagram i in the figure below, the converter is functioning as a high- speed bridge between switches creating increased cap...

  • Page 27

    10base-t to 10base-fl converter 23 application diagram ii in the figure below, the converter is functioning as a server aggregation for an enterprise or lan configuration. It is providing a 10mbps full duplex link to a workgroups of 10/100 switches located on separate floors within a single building...

  • Page 28

    10base-t to 10base-fl converter 24 volktek corporation 4f, no. 192 lian-cheng road chung-ho, taipei 235, taiwan roc tel: +86 (2) 8242-1000 fax: +886 (2) 8242-3333 tech support: +886 800-286-286 iso 9001 certified.