1. DL manuals
  2. Wacker Neuson
  3. Power Tool
  4. VP 1340A
  5. Operator's Manual

Wacker Neuson VP 1340A Operator's Manual

Manual is about: Vibroplate

Summary of VP 1340A

  • Page 1

    Operator’s manual vibroplate vp 1340a vp 1340aw vp 1550a vp 1550aw 0 1 5 4 5 6 9 e n 0154569en / 008.

  • Page 3: Vp 1340A/vp 1550A

    Vp 1340a/vp 1550a table of contents wc_bo0154569008entoc.Fm 1 foreword 3 1 safety information 4 1.1 laws pertaining to spark arresters ...................................................... 4 1.2 operating safety .................................................................................. 5 1....

  • Page 4: Table Of Contents

    Table of contents vp 1340a/vp 1550a wc_bo0154569008entoc.Fm 2 4 maintenance 18 4.1 periodic maintenance schedule ..........................................................18 4.2 spark plug ...........................................................................................20 4.3 air cleaner ....

  • Page 5

    Wc_tx000001gb.Fm 3 california proposition 65 warning: engine exhaust, some of its constituents, and certain vehicle components, contain or emit chemicals known to the state of california to cause cancer and birth defects or other reproductive harm. Foreword this manual provides information and proce...

  • Page 6: Safety Information

    Safety information vp 1340a/vp 1550a wpm_si000305gb.Fm 4 1. Safety information this manual contains danger, warning, caution, notice and note callouts which must be followed to reduce the possibility of personal injury, damage to the equipment, or improper service. This is the safety alert symbol. I...

  • Page 7: Vp 1340A/vp 1550A

    Vp 1340a/vp 1550a safety information wpm_si000305gb.Fm 5 1.2 operating safety familiarity and proper training are required for the safe operation of the machine. Machines operated improperly or by untrained personnel can be hazardous. Read the operating instructions contained in this manual and the ...

  • Page 8: Safety Information

    Safety information vp 1340a/vp 1550a wpm_si000305gb.Fm 6 1.3 operator safety while using internal combustion engines internal combustion engines present special hazards during operation and fueling. Read and follow the warning instructions in the engine owner’s manual and the safety guidelines below...

  • Page 9: Vp 1340A/vp 1550A

    Vp 1340a/vp 1550a safety information wpm_si000305gb.Fm 7 1.4 service safety a poorly maintained machine can become a safety hazard! In order for the machine to operate safely and properly over a long period of time, periodic maintenance and occasional repairs are necessary. 1.4.1 do not attempt to c...

  • Page 10: Safety Information

    Safety information vp 1340a/vp 1550a wpm_si000305gb.Fm 8 1.5 label locations wpmgr005939.

  • Page 11: Vp 1340A/vp 1550A

    Vp 1340a/vp 1550a safety information wpm_si000305gb.Fm 9 1.6 warning and informational labels wacker neuson machines use international pictorial labels where needed. These labels are described below: label meaning warning! Always wear hearing and eye protection when operating this machine. Warning! ...

  • Page 12: Safety Information

    Safety information vp 1340a/vp 1550a wpm_si000305gb.Fm 10 throttle control lever: turtle = idle or slow rabbit = full or fast danger! Engines emit carbon monoxide; operate only in well-ventilated area. Read the operator’s manual. No sparks, flames, or burning objects near the machine. Shut off the e...

  • Page 13: Vp 1340A/vp 1550A

    Vp 1340a/vp 1550a safety information wpm_si000305gb.Fm 11 this machine may be covered by one or more patents. Label meaning.

  • Page 14: Technical Data

    Technical data vp 1340a/vp 1550a wpm_td000314gb.Fm 12 2. Technical data 2.1 engine data engine power rating net power rating per sae j1349. Actual power output may vary due to conditions of specific use. Vp 1340a/aw 0009031 0009032 vp 1550a/aw 0009027 0009028 engine engine make honda engine model gx...

  • Page 15: Vp 1340A/vp 1550A

    Vp 1340a/vp 1550a technical data wpm_td000314gb.Fm 13 2.2 machine data 2.3 sound and vibration measurements the required sound specification, paragraph 1.7.4.F of 89/392/eec machinery directive, is: • the guaranteed sound power level (l wa ) = 108 db(a). • the sound pressure level at operator’s loca...

  • Page 16: Technical Data

    Technical data vp 1340a/vp 1550a wpm_td000314gb.Fm 14 2.4 dimensions mm (in.) 588 (23) 400 (16) 911 (36) wpmgr005966.

  • Page 17: Vp 1340A/vp 1550A

    Vp 1340a/vp 1550a operation wpm_tx001087gb.Fm 15 3. Operation 3.1 recommended fuel the engine requires regular grade unleaded gasoline. Use only fresh, clean gasoline. Gasoline containing water or dirt will damage fuel system. Consult engine owner’s manual for complete fuel specifications. 3.2 appli...

  • Page 18: Operation

    Operation vp 1340a/vp 1550a wpm_tx001087gb.Fm 16 3.4 to start see graphic: wc_gr000014 3.4.1 open fuel valve by moving lever to the right (a1) . Note : if engine is cold, move choke lever to close position (b1) . If engine is hot, set choke to open position (b2) . 3.4.2 turn engine switch to “on” (e...

  • Page 19: Vp 1340A/vp 1550A

    Vp 1340a/vp 1550a operation wpm_tx001087gb.Fm 17 3.6 operation run the engine at full throttle and allow the plate to pull itself along at its normal speed. When operating on an incline it may be necessary to assist the plate by pushing it forward slightly. When operating downhill hold the plate bac...

  • Page 20: Maintenance

    Maintenance vp 1340a/vp 1550a wpm_tx001088gb.Fm 18 4. Maintenance 4.1 periodic maintenance schedule 4.1.1 engine maintenance the chart below lists basic engine maintenance. Refer to the engine manufacturer’s operation manual for additional information on engine maintenance. Daily before starting aft...

  • Page 21: Vp 1340A/vp 1550A

    Vp 1340a/vp 1550a maintenance wpm_tx001088gb.Fm 19 4.1.2 machine maintenance the chart below lists basic machine maintenance. Note: when machine is being used in asphalt, it is highly recommended that shockmounts are replaced every year or after 300 hours of usage. Daily before starting after first ...

  • Page 22: Maintenance

    Maintenance vp 1340a/vp 1550a wpm_tx001088gb.Fm 20 4.2 spark plug see graphic: wc_gr000028 clean or replace the spark plug as needed to ensure proper operation. Refer to your engine operator’s manual. The muffler becomes very hot during operation and remains hot for a while after stopping the engine...

  • Page 23: Vp 1340A/vp 1550A

    Vp 1340a/vp 1550a maintenance wpm_tx001088gb.Fm 21 4.3 air cleaner see graphic: wc_gr000025 the engine is equipped with a dual element air cleaner. Service air cleaner frequently to prevent carburetor malfunction. Notice : never run engine without air cleaner. Severe engine damage will occur. Never ...

  • Page 24: Maintenance

    Maintenance vp 1340a/vp 1550a wpm_tx001088gb.Fm 22 4.4 engine oil see graphic: wc_gr000022 4.4.1 drain the oil while the engine is still warm. 4.4.2 remove the oil filler plug (a) and the drain plug (b) to drain the oil. Note: in the interests of environmental protection, place a plastic sheet and a...

  • Page 25: Vp 1340A/vp 1550A

    Vp 1340a/vp 1550a maintenance wpm_tx001088gb.Fm 23 4.6 carburetor adjustment see graphic: wc_gr000032 4.6.1 start the engine and allow it to warm up to operating temperature. 4.6.2 set the pilot screw (a) two turns out. See note . 4.6.3 with the engine idling, turn the pilot screw (a) in or out to t...

  • Page 26: Maintenance

    Maintenance vp 1340a/vp 1550a wpm_tx001088gb.Fm 24 4.8 drive belt see graphic: wpmgr005992 on new machines or after installing a new belt, check the belt tension after first 20 hours of operation. Check and adjust the belt every 50 hours thereafter. To adjust the belt: 4.8.1 loosen the two screws (a...

  • Page 27: Vp 1340A/vp 1550A

    Vp 1340a/vp 1550a maintenance wpm_tx001088gb.Fm 25 4.9 exciter lubrication see graphic: wpmgr006018 the bearings in the exciter assembly are splash lubricated and rotate at very high speed. It is important to maintain the exciter oil at the correct level and change it regularly. Check oil level in e...

  • Page 28: Maintenance

    Maintenance vp 1340a/vp 1550a wpm_tx001088gb.Fm 26 4.11 lifting machine see graphic: wpmgr006022 see technical data for weight of the machine. To lift machine manually: 4.11.1 stop the engine. 4.11.2 obtain help from a partner and plan the lift. To avoid burns or fire hazards, let the engine cool be...

  • Page 29: Vp 1340A/vp 1550A

    Vp 1340a/vp 1550a maintenance wpm_tx001088gb.Fm 27 4.12 transporting machine see graphic: wpmgr006042 to avoid burns or fire hazards, let engine cool before transporting machine or storing indoors. 4.12.1 turn fuel valve to the off position and keep the engine level to prevent fuel from spilling. 4....

  • Page 30: Maintenance

    Maintenance vp 1340a/vp 1550a wpm_tx001088gb.Fm 28 4.14 troubleshooting problem / symptom reason / remedy plate does not develop full speed. Poor compaction. • engine throttle control not completely open. • throttle control not adjusted correctly. • ground too wet, plate sticking. Allow soil to dry ...

  • Page 31

    Vp 1340a_1550a_q_2009_wn.Fm heinz gengnagel president & ceo wacker neuson manila, inc. Date / datum / fecha / date ec declaration of conformity eg-konformitÄtserklÄrung ce-declaraciÓn de conformidad dÉclaration de conformitÉ de la cee wacker neuson manila, inc., dasmariÑas, cavite, philippines hereb...

  • Page 32

    Wacker construction equipment ag · preußenstraße 41 · d-80809 münchen · tel.: +49-(0)89-3 54 02 - 0 · fax: +49 - (0)89-3 54 02-3 90 wacker neuson corporation · p.O. Box 9007 · menomonee falls, wi 53052-9007 · tel. : (262) 255-0500 · fax: (262) 255-0550 · tel. : (800) 770-0957 wacker asia pacific ope...