- DL manuals
- Wacker Neuson
- Power Tool
- VP 2050
- Operator's Manual
Wacker Neuson VP 2050 Operator's Manual
Summary of VP 2050
Page 1
Operator’s manual vibroplate vp 2050 vp 2050w 500191658 005 0110 5 0 0 0 1 9 1 6 5 8.
Page 2
Copyright notice © copyright 2010 by wacker neuson corporation. All rights, including copying and distribution rights, are reserved. This publication may be photocopied by the original purchaser of the machine. Any other type of reproduction is prohibited without express written permission from wack...
Page 3: Vp 2050/w
Vp 2050/w table of contents wpm_bo0400324005entoc.Fm 1 foreword 3 1. Safety information 4 1.1 laws pertaining to spark arresters ...................................................... 4 1.2 operating safety .................................................................................. 5 1.3 oper...
Page 4: Table of Contents
Table of contents vp 2050/w wpm_bo0400324005entoc.Fm 2 4. Maintenance 18 4.1 periodic maintenance schedule ..........................................................18 4.2 spark plug ...........................................................................................20 4.3 air cleaner ..........
Page 5
Wc_tx000001gb.Fm 3 california proposition 65 warning: engine exhaust, some of its constituents, and certain vehicle components, contain or emit chemicals known to the state of california to cause cancer and birth defects or other reproductive harm. Foreword this manual provides information and proce...
Page 6: Safety Information
Safety information vp 2050/w wpm_si000312gb.Fm 4 1. Safety information this manual contains danger, warning, caution, notice, and note signal words which must be followed to reduce the possibility of personal injury, damage to the equipment, or improper service. This is the safety alert symbol. It i...
Page 7: Vp 2050/w
Vp 2050/w safety information wpm_si000312gb.Fm 5 1.2 operating safety familiarity and proper training are required for the safe operation of the machine. Machines operated improperly or by untrained personnel can be hazardous. Read the operating instructions contained in this manual and the engine m...
Page 8: Safety Information
Safety information vp 2050/w wpm_si000312gb.Fm 6 1.3 operator safety while using internal combustion engines internal combustion engines present special hazards during operation and fueling. Read and follow the warning instructions in the engine owner’s manual and the safety guidelines below. Failur...
Page 9: Vp 2050/w
Vp 2050/w safety information wpm_si000312gb.Fm 7 1.4 service safety a poorly maintained machine can become a safety hazard! In order for the machine to operate safely and properly over a long period of time, periodic maintenance and occasional repairs are necessary. 1.4.1 do not attempt to clean or ...
Page 10: Safety Information
Safety information vp 2050/w wpm_si000312gb.Fm 8 1.5 label locations wpmgr005945.
Page 11: Vp 2050/w
Vp 2050/w safety information wpm_si000312gb.Fm 9 1.6 warning and informational labels wacker neuson machines use international pictorial labels where needed. These labels are described below: label meaning warning! Hot surface! Guaranteed sound power level in db(a). Warning! Hand injury if caught in...
Page 12: Safety Information
Safety information vp 2050/w wpm_si000312gb.Fm 10 throttle control lever: rabbit = full or fast turtle = idle or slow danger! Engines emit carbon monoxide; operate only in well-ventilated area. Read the operator’s manual for machine infor- mation. Danger! Before fueling, stop the engine. No sparks, ...
Page 13: Vp 2050/w
Vp 2050/w safety information wpm_si000312gb.Fm 11 a nameplate listing the model number, item number, revision number, and serial number is attached to each unit. Please record the infor- mation found on this plate so it will be avail- able should the nameplate become lost or damaged. When ordering p...
Page 14: Technical Data
Technical data vp 2050/w wpm_td000321gb.Fm 12 2. Technical data 2.1 engine data engine power rating net power rating per sae j1349. Actual power output may vary due to conditions of specific use. Vp 2050 0009530 vp 2050w 0009537 engine engine make wacker engine model wm170 maximum rated power @ rate...
Page 15: Vp 2050/w
Vp 2050/w technical data wpm_td000321gb.Fm 13 2.2 machine data 2.3 sound and vibration measurements the required sound specification, paragraph 1.7.4.F of 89/392/eec machinery directive, is: • the guaranteed sound power level (l wa ) = 108 db(a). • the sound pressure level at operator’s location (l ...
Page 16: Technical Data
Technical data vp 2050/w wpm_td000321gb.Fm 14 2.4 dimensions mm (in.) 500 (20) 588 (23) 919 (36) wpmgr005973.
Page 17: Vp 2050/w
Vp 2050/w operation wpm_tx001101gb.Fm 15 3. Operation 3.1 recommended fuel the engine requires regular grade unleaded gasoline. Use only fresh, clean gasoline. Gasoline containing water or dirt will damage fuel system. Consult engine owner’s manual for complete fuel specifications. 3.2 application t...
Page 18: Operation
Operation vp 2050/w wpm_tx001101gb.Fm 16 3.4 to start see graphic: wc_gr000655 3.4.1 open fuel valve by moving lever down (a1). Note: if engine is cold, move choke lever to close position (d2). If engine is hot, set choke to open position (d1). 3.4.2 turn engine switch to “on” (b2). 3.4.3 open throt...
Page 19: Vp 2050/w
Vp 2050/w operation wpm_tx001101gb.Fm 17 3.6 operation run the engine at full throttle and allow the plate to pull itself along at its normal speed. When operating on an incline it may be necessary to assist the plate by pushing it forward slightly. When operating downhill hold the plate back slight...
Page 20: Maintenance
Maintenance vp 2050/w wpm_tx001102gb.Fm 18 4. Maintenance 4.1 periodic maintenance schedule 4.1.1 engine maintenance the chart below lists basic engine maintenance. Refer to the engine manufacturer’s operation manual for additional information. Daily before starting after first 20 hrs. Every 2 weeks...
Page 21: Vp 2050/w
Vp 2050/w maintenance wpm_tx001102gb.Fm 19 4.1.2 machine maintenance the chart below lists basic machine maintenance. Note: when machine is being used in asphalt, it is highly recommended that shockmounts are replaced every year or after 300 hours of usage. Daily before starting after first 20 hrs. ...
Page 22: Maintenance
Maintenance vp 2050/w wpm_tx001102gb.Fm 20 4.2 spark plug see graphic: wc_gr000028 clean or replace the spark plug as needed to ensure proper operation. Refer to your engine operator’s manual. The muffler becomes very hot during operation and remains hot for a while after stopping the engine. Do not...
Page 23: Vp 2050/w
Vp 2050/w maintenance wpm_tx001102gb.Fm 21 4.3 air cleaner see graphic: wc_gr000656 never use gasoline or other types of low-flash point solvents for cleaning the air cleaner. A fire or explosion could result. Notice: never run the engine without the air cleaner. Severe engine damage will occur. The...
Page 24: Maintenance
Maintenance vp 2050/w wpm_tx001102gb.Fm 22 4.4 engine oil see graphic: wc_gr000087 4.4.1 drain oil while engine is still warm. Note: in the interests of environmental protection, place a plastic sheet and a container under the machine to collect any liquid which drains off. Dispose of this liquid in...
Page 25: Vp 2050/w
Vp 2050/w maintenance wpm_tx001102gb.Fm 23 4.6 cleaning fuel strainer see graphic: wc_gr001093 4.6.1 to remove water and dirt, close the fuel lever and remove the fuel strainer. 4.6.2 inspect the fuel strainer (a) for water and dirt. 4.6.3 after removing any dirt and water, wash the fuel cup with a ...
Page 26: Maintenance
Maintenance vp 2050/w wpm_tx001102gb.Fm 24 4.7 drive belt see graphic: wpmgr005997 on new machines or after installing a new belt, check the belt tension after first 20 hours of operation. Check and adjust the belt every 50 hours thereafter. To adjust the belt: 4.7.1 loosen the two screws (a) on the...
Page 27: Vp 2050/w
Vp 2050/w maintenance wpm_tx001102gb.Fm 25 4.8 exciter lubrication see graphic: wpmgr006020 the bearings in the exciter assembly are splash lubricated and rotate at very high speed. It is important to maintain the exciter oil at the correct level and change it regularly. Check oil level in exciter e...
Page 28: Maintenance
Maintenance vp 2050/w wpm_tx001102gb.Fm 26 4.10 lifting machine see graphic: wpmgr006169 see technical data for weight of machine. To lift machine manually: 4.10.1 stop the engine. 4.10.2 obtain help from a partner and plan the lift. To avoid burns or fire hazards, let the engine cool before transpo...
Page 29: Vp 2050/w
Vp 2050/w maintenance wpm_tx001102gb.Fm 27 4.11 transporting machine see graphic: wpmgr006043 to avoid burns or fire hazards, let engine cool before transporting machine or storing indoors. 4.11.1 turn fuel valve to the off position and keep the engine level to prevent fuel from spilling. 4.11.2 tie...
Page 30: Maintenance
Maintenance vp 2050/w wpm_tx001102gb.Fm 28 4.13 troubleshooting problem / symptom reason / remedy plate does not develop full speed. Poor compaction. • engine throttle control not completely open. • throttle control not adjusted correctly. • ground too wet, plate sticking. Allow soil to dry before c...
Page 31
Heinz gengnagel president & ceo wacker neuson corporation date vp 20 50- en_2 01 0_ wn .Fm the original language of this ec declaration of conformity is american english. Ec declaration of conformity wacker neuson manila, inc., dasmariÑas, cavite, philippines hereby certifies that the construction e...
Page 33
Heinz gengnagel president & ceo wacker neuson corporation datum vp 20 50- de_2 01 0_ wn .Fm diese eg-konformitätserklärung ist eine Übersetzung des originalzertifikats. Ce-konformitÄtserklÄrung wacker neuson manila, inc., dasmariÑas, cavite, philippines bescheinigt, daß das baugerät: 1. Art: rüttelp...
Page 35
Heinz gengnagel president & ceo wacker neuson corporation fecha vp 20 50- es_20 10 _w n .Fm esta declaración de conformidad ce presenta una traducción del certificado original. DeclaraciÓn de conformidad de la ce wacker neuson manila, inc., dasmariÑas, cavite, philippines certifica que la máquina de...
Page 37
Heinz gengnagel president & ceo wacker neuson corporation date vp 20 50- fr _2 01 0_ w n .Fm cette déclaration de conformité ce est une traduction du certificat d’origine. DÉclaration de conformitÉ c.E. Wacker neuson manila, inc., dasmariÑas, cavite, philippines atteste que le matériel: 1. Catégorie...
Page 38
Important: for spare parts information, please see your wacker neuson dealer, or visit the wacker neuson website at http://www.Wackerneuson.Com/. Wichtig! Informationen über ersatzteile erhalten sie von ihrem wacker neuson händler oder besuchen sie die wacker neuson website unter http://www.Wackerne...