English français español 0913 • form no. 0529843b owner’s manual read this manual for complete instructions français (page 17) / español (página 33) paintready™ station contents 2 important safety information 4 controls and functions 5 material preparation 6 assembly 8 air and material controls 9 sp...
English 2 © wagner spray tech - all rights reserved important safety information read all safety information before operating the equipment. Save these instructions. Indicates a hazardous situation which, if not avoided, could result in death or serious injury. To reduce the risks of fire or explosi...
English © wagner spray tech - all rights reserved 3 important safety information warning - to reduce the risk of injury: 1. Always wear appropriate gloves, eye protection, clothing and a respirator or mask when painting. Hazardous vapors – paints, solvents, insecticides, and other materials can be h...
English 4 © wagner spray tech - all rights reserved controls and functions air hose spray gun turbine spray gun handle air pressure control selector material flow control filter housing turbine handle spray gun holder trigger material contaner adjustment ring spray width lever air pressure control s...
English © wagner spray tech. - all rights reserved 5 material preparation note: material to be sprayed may need to be strained to remove any impurities in the paint which may enter and clog the system. Impurities in the paint will give poor performance and a poor finish. To prepare the material: 1. ...
English 6 © wagner spray tech. - all rights reserved assembly before you begin: never point the spray gun at any part of the body. To assemble: important: make sure the power cord is unplugged. 1. Insert the suction tube into the intake opening. 2. Align the suction tube - a. If you are going to be ...
English © wagner spray tech - all rights reserved 7 assembly (continued) 4. Align the arrow on the spray gun with the “unlock” symbol on the spray gun handle. 5. Insert and twist the spray gun into the handle toward the “lock” symbol on the spray gun handle. The tab below the trigger will lock the t...
English 8 © wagner spray tech - all rights reserved air and material controls spray performance will depend upon a number of factors: material thickness, spray pattern selected, material volume, and air pressure. With any type of air-assisted spraying, desired spray results will be achieved through ...
English © wagner spray tech - all rights reserved 9 spray pattern adjustment adjust spray shape the spray pattern shape is adjusted by turning the adjustment ring to either the vertical or horizontal positions. The positions of the air cap and the corresponding spray pattern shapes are illustrated b...
English 10 © wagner spray tech - all rights reserved proper spraying technique stop the room you are spraying must be properly masked in order to prevent overspray from covering woodwork, floors or furnishings. Make sure you have properly masked the room per the instructions on the enclosed “taping ...
English © wagner spray tech - all rights reserved 11 proper spraying technique pattern examples use the images and guidelines below in order to assist you in achieving the desired spray pattern for your project. These are meant to be general starting points - you may have to slightly modify certain ...
English 12 © wagner spray tech - all rights reserved cleanup flushing the unit before you begin: when cleaning, use the appropriate cleaning solution (warm, soapy water for latex materials; mineral spirits for oil-based materials) important: never clean air cap or air holes in the nozzle with sharp ...
English © wagner spray tech - all rights reserved 13 cleanup (continued) cleaning the gun to clean the spray gun: 1. Make sure power cord is unplugged. Remove the air hose from the rear of the spray gun handle. 2. Remove the adjustment ring (a) carefully from the connecting nut (b). Loosen the conne...
English 14 © wagner spray tech - all rights reserved reassembly to reassemble: 1. Install the nozzle seal* (1) with the groove (a) (slot) facing toward the nozzle (away from the front end assembly). 2. Insert the nozzle (2). Make sure to align the groove (b) and notch (c) and align the nozzle openin...
English © wagner spray tech. - all rights reserved 15 maintenance cleaning the filters: important: before every use, you should inspect the air filter in the turbine to see if it is excessively dirty. If it is dirty, follow these steps to replace it. Important: never operate your unit without the ai...
English 16 © wagner spray tech. - all rights reserved troubleshooting problem cause solution problem a: little or no material flow 1. Nozzle clogged. 2. Suction tube clogged. 3. Material flow setting too low. 4. Suction tube loose. 5. Air vent on suction tube blocked. 6. No pressure build up in cont...
1 3 4 2 # part no. Nº de piéce pieza no. English description français description español descripción qty. Qte. Cant. 1 ------- turbine (includes item 2) turbine (inclut de pièce 2) turbina (incluye le articulo 2) 1 2 2307279 filter filtre filtro 2 3 0414219 air hose tuyau d’air manguera de aire 1 4...
Español français english 50 © wagner spray tech - all rights reserved parts list • liste de pièces • lista de piezas 1 8 2 3 4 6 7 5 replacement parts available by calling customer service on peut obtenir des pièces de rechange en appelant le service à la clientèle. Los repuestos están disponibles l...
English français español © wagner spray tech - all rights reserved 51 garantie limitée pulvérisateur de peinture hvlp cet article fabriqué par wagner spray tech corporation (wagner) est garanti contre tout défaut de fabrication et de matériaux pour une période d’un an suivant la date d’achat, à cond...
Español français english 52 © wagner spray tech - all rights reserved limited warranty hvlp paint spray equipment this product, manufactured by wagner spray tech corporation (wagner), is warranted against defects in material and work-manship for one year following date of purchase if operated in acc...
