WAGNER 505 Owner's Manual

Manual is about: HIGH PERFORMANCE AIRLESS SPRAYER

Summary of 505

  • Page 1

    1 printed in the u. S. A. R form no. 0270993-11/93 505 high performance airless sprayer questions? ... Need help? Wagner maintains a toll-free help line for you should you have any comments or problems with this wagner product. Call us first ....For answers fast... Wagner technical service 1-800-328...

  • Page 2: General Description

    2 contents general description ....................................................... 2 safety precautions ...................................................... 3-6 extension cord ............................................................... 7 grounding instructions ................................

  • Page 3: Warning

    3 safety precautions this manual contains information which must be read and understood before using the equipment. When you come to an area which has one of the following symbols, pay particular attention and make certain to heed the safeguard. Warning important safety information indicates a hazar...

  • Page 4: Warning

    4 warning prevention hazard • maximum operating range of the gun - 2500 psi fluid pressure. • never aim the gun at any part of the body. • never allow any part of the body to come in contact with the fluid stream. Do not come in contact with a fluid stream created by a leak in the fluid hose. • neve...

  • Page 5: Warning

    5 explosion or fire - solvent and paint fumes can explode or ignite, causing property damage and or severe injury. Warning hazard prevention • exhaust and fresh air introduction must be provided to keep the air within the spray area free from accumulation of flammable vapors. • avoid all ignition so...

  • Page 6: Warning

    6 warning prevention hazard explosion hazard incompatible materials - may cause property damage or severe injury. Hazardous vapors - paints, solvents, insecticides, and other materials may be harmful if inhaled causing se- vere nausea, fainting, or poisoning. General - may cause property damage or s...

  • Page 7: Grounding Instructions

    7 note: more than 100 feet of extension cord is not recommended. Use more paint hose, not more extension cord. Shorter extension cords will assure maximum electrical power for proper operation. Grounding instructions this product must be grounded. In the event of an electrical short circuit, groundi...

  • Page 8: Pressure Relief Procedure

    8 pressure relief procedure follow this procedure after the unit is assembled and before any operation which involves the spray gun such as changing tips or accessories, or cleaning and maintenance. 1. Make sure pressure control knob is at its lowest setting (counterclockwise). 2. Turn priming knob ...

  • Page 9: Set-Up

    9 pail bracket set-up figure 3b - attaching cart handle bolt, washer and wing nut cart handle assemble cart 2. Attach cart handle (3). Face the hose hook toward the front of the unit. Use two bolts, washers and wing nuts (4), tightening securely. See figure 3b. Figure 2 – cart assembly diagram 4 2 t...

  • Page 10: Set-Up

    10 set-up 1. Lock gun. See figure 4. Figure 4 - gun in locked & unlocked position attach tip to gun 2. If spray tip is not pre- assembled, (see figure 5) insert tip (1) into tip guard, (2) and turn 90 ° coun- terclockwise to spray position (arrow pointing away from gun). Cylinder of tip forms a stop...

  • Page 11: Set-Up

    11 set-up attach return hose 1. Be sure motor switch is turned off. 2. Screw brass fitting of return tube into upper port on side of pump. (the brass fitting is located in the literature set.) tighten firmly by hand. See figure above. 3. Press return tube (small tube) to brass fitting and fasten wit...

  • Page 12: Priming

    12 priming 1. Lay unit back on its handle so inlet valve is facing up. Fill inlet valve with water or light household oil. 2. Make sure prime/spray knob is in prime a position and pressure knob is turned to the lowest pressure. (counter clockwise) see figure 11. Turn unit on. Pressure control knob p...

  • Page 13: Priming

    13 figure 17 - attaching paint pail handle prime the pump 1. Attach suction tube to inlet valve and tighten firmly by hand. See figure 15. Be sure threads are straight so the fitting turns freely without binding. Figure 15 - attaching suction tube 2. Place suction tube and return tube in paint. See ...

  • Page 14: Priming

    14 priming 3. Turn sprayer on. 4. Turn pressure control knob between half and full pressure. See figure 20. You should then be able to see the paint move through the suction tube to the pump. Continue until paint flows through the return tube. (let unit prime 1 to 2 minutes). Figure 20 - turn pressu...

  • Page 15: Spraying

    15 spraying figure 24 - paint tailing pattern good spray pattern practice first 1. Be sure paint hose is free of kinks and clear of traffic or objects with sharp cutting edges. 2. Return pressure control knob to its lowest setting (counterclockwise). Figure 21. 3. Turn priming knob to spray b positi...

  • Page 16: Spraying

    16 spraying 1. The key to a good paint job is an even coating over the entire surface. With spray painting, this is done by using even strokes, with your arm moving at a con- stant speed and keeping the spray gun a constant distance from the surface. 2. In most cases, the best spraying distance is 1...

  • Page 17: Spraying

    17 5. The spray gun should be triggered off at the end of each stroke and on again at the beginning of the next. This avoids paint buildup at the end of the stroke which may result in runs and sags. Triggering at the end of the stroke also saves paint and results in a better looking job. See figure ...

  • Page 18: Spraying

    18 figure 32 - remove and clean screen spraying continued from page 17 cleaning the spray gun filter the spray gun includes a filter to catch particles before they reach the spray tip. If this filter becomes clogged or obstructed it will reduce the flow of paint, changing the spray pattern and possi...

  • Page 19: Clean Up

    19 short-term/overnight storage shut-down 1. Lock the gun and reduce the pressure. Turn the sprayer to prime a and shut it off. Unplug sprayer. Leave the suction set in the paint. Refer to pressure relief procedure. 2. For latex materials only, pour 1/2 cup water slowly on the top of the paint to pr...

  • Page 20: Cleanup

    20 do not allow paint to build up on the motor. Overheating of the motor will result. Do not allow flammable solvents to come in contact with the motor, which could ignite. Note: you will need an extra bucket with cleaning solution, a toothbrush, an adjustable wrench and rags. Cleanup warning shut d...

  • Page 21: Clean Up

    21 15. Attach paint hose to gun,tighten with two wrenches. Clean up 14. Clean spray tip and gun filter with a soft brush. Reassemble spray tip in cleaning position. (arrow points to back of the gun.) 16. Turn the unit on and unlock gun trigger. Turn to spray b and point gun to side of cleaning bucke...

  • Page 22: Clean Up

    22 clean up 21. Lock gun, reduce pressure and turn prime/spray knob to prime a . 22. Lay unit back on handle so inlet valve is facing upward. Clean threads of inlet valve with a damp cloth. Fill inlet valve with light household oil. See figure 43. Slowly increase pressure to distribute the oil throu...

  • Page 23: Maintenance

    23 maintenance 4. Thoroughly clean the valve assembly with solvent and brush. 5. A properly seated valve filled with water and held vertically will not drip out the bottom of the valve. If you have properly cleaned the valve and water drips out the bottom, the valve is worn and needs to be replaced....

  • Page 24: Maintenance

    24 maintenance 2. If possible, leave the copper washer under the cap in place. At least be sure to replace it with the same side up. (the top will show the imprint of the end cap, while the bottom should be perfectly flat to match seat in the pump casting.) see paint pump assem- bly parts diagram,it...

  • Page 25: Optional Hopper Assembly

    25 optional hopper assembly converting sprayer for hopper operation hopper return tube hopper figure 49 - optional hopper 4. Screw in the plastic return tube fitting into the paint pump port that the brass fitting was removed from. Attach hopper return tube to the fitting where the suction set retur...

  • Page 26: Trouble Shooting

    26 problem cause remedy sprayer does not start up. Sprayer not plugged in. Plug in. On/off switch off. Flip switch to on. Blown fuse in circuit. Replace fuse. No voltage or low voltage test power supply voltage. At wall plug. Unit turned off under pressure. Turn prime/spray knob to prime position. D...

  • Page 27: Trouble Shooting

    27 problem cause remedy spray gun won't shut off. Worn ball or seat. Take to authorized wagner service center. Foreign matter or paint take to authorized wagner service center. Buildup or dried paint between ball and seat. (caused by improper cleaning of gun. Spray gun leaks. Worn or dirty internal ...

  • Page 28

    28 item part no. Description qty. Parts diagram – final assembly 1 0288478 grip, handle 1 2 0270357 handle, cart 1 3 9821503 washer, lock 4 4 9810111 nut, wing 2 5 0270356 cart assembly 1 6 0270359 wheel 2 item part no. Description qty. 1 2 3 4 5 6 7 4 3 8 9 10 11 9 7 0275728 cap, hub 2 8 0270358 br...

  • Page 29: Caution

    29 item part no. Description qty. Item part no. Description qty. 1 0281113 valve, inlet assembly 1 (includes item 12) 2 0089564 cap, outlet assembly 1 3 9970103 washer, sealing, copper 2 4 0047485 spring, outlet 1 5 0093635 ball, 6mm, carbide 1 6 0090348 seat, ball, outlet assembly 1 parts diagram –...

  • Page 30: 0270174

    30 1 2 3 9 12 11 10 item part no. Description qty. Item part no. Description qty. 7 0270371 housing, filter 1 8 0270369 filter 1 9 0090621 washer 1 10 0088715 fitting, return hose 1 11 0089096 clamp 1 12 0270363 tubing, return 1 1 0270133 suction tube complete 1 (includes items 2 thru 10) 2 0090622 ...

  • Page 31: Accessories

    31 1 7 3 4 5 6 accessories part description number 0153000 hose, 25' x 3/16", grounded 0153001 hose, 50' x 3/16', grounded 0093896 hose connector 0149018 g-09 spray gun 0149017 g-10 spray gun 0089731 gun filter assembly 0154675 gun filters, medium/fine 0093820 adjustable tip part description number ...

  • Page 32: Parts And Accessories

    32 parts and accessories parts list item part no. Description 1 0293004 g-06 gun assembly 2 0089731 filter assembly (includes items 3,4,5,6) 3 0043590 spring 4 0089694 seal, nylon 5 0089692 housing filter 6 0089959 filter item part no. Description 3 4 5 2 6 1 9 10 7 8 7 0293303 guide, hose 8 0154782...

  • Page 33: Limited Warranty

    33 r wagner spray tech corporation 1770 fernbrook lane minneapolis, minnesota 55447 telephone (612) 553-7000 limited warranty airless paint spray equipment this product, manufactured by wagner spray tech corporation (wagner), is warranted to the original retail purchaser against defects in material ...