Moisture meter instruction manual wagner model bi 2200
2 table of contents introduction..................................................................................................3 the wagner meters moisture meter defined ..........................3 features .............................................................................................
3 introduction the power of the wagner meters brand speaks loudly of the company’s strategy of building superior products. Over the years, wagner meters has associated itself with some of the biggest names in construction materials. This means consistently delivering real value to customers. Wagner ...
4 general moisture indication for many different industries who only require relative readings. Features • uses wagner’s non-invasive patented electromagnetic wave technology • selectable material range includes wood, tile, shingles, plaster, drywall, linoleum, fiberglass, veneer, synthetic stucco, ...
5 on/off function • compact pocket-size design • rugged design • user-friendly 2-button operation • low battery indicator • complete with 9-volt battery and protective holster • factory-direct technical support • light weight and compact design the ingenious 2 button control panel makes the operatio...
6 on/ hold otherwise automatic turn off will occur after one minute if the meter is not in use. Inspection function turn on the meter (the firmware version 2.2.0 will appear briefly). Set the meter on the material to be scanned. Press down firmly on the center of the meter with approximately 3 pound...
7 m a (÷) symbol will appear on the left side of the screen. This will indicate the hold mode. To clear the screen, press the on/ hold button again. Material sensitivity range there are three ways to use the material sensitivity range feature. 1. You can use the factory setting of :50 for the moistu...
8 firmware version 2.2.0 clears from the screen, press the m button. The meter display will show the current material setting. The factory preset number is :50. Press the m button a second time. The colon (:) will blink, indicating that you are in the change mode. Next, hold the m button down to inc...
9 materials. This is a feature that may not be needed by most users. If you would like to adjust the material sensitivity range anywhere between :20 to 1:00 for customized projects you may use the instructions outlined above. (note: you may press the m button to increment the selected material setti...
10 readings at the stain, compared to the base line can indicate elevated moisture near the stain area. Your moisture meter may respond to metal in a wall as it would to an increase in moisture content. To determine if the elevated readings are caused by metal, scan in the direction of a straight li...
11 are steel frames that join drywall at corners (bead and trim), fasteners, flashing and metal channels. You do not need to be concerned with metal at depths greater than 1 inch to 1 1 / 2 inch from the surface being scanned. Please note that as you scan across studs, the readings will be elevated ...
12 low battery indicator when the lo bat indicator is on, you should replace the battery to insure the meter will function properly. If the battery needs to be replaced, use a 9-volt alkaline battery. Be sure to observe proper battery polarity. Meter storage for a long service life, it is important ...
13 bi 2200 meter specifications size: length 4 9 / 16 inches width 2 3 / 4 inches height 1 1 / 16 inches scanning area: length 2 1 / 2 inches width 1 1 / 2 inches scanning depth: 3 / 4 inch weight: 0.37 pounds power: 9 volt alkaline auto shut down: 60 seconds.
14 materials settings table these material settings are provided to give users general correction factors for various construction materials. Material setting material :50 boat structures (fiberglass) 1:00 brick :50 ceramic tile 1:00 concrete :50 drywall / sheetrock :50 engineered / laminated wood :...
15 fcc compliance statement this equipment has been tested and found to comply within the limits for a class b digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment ge...
16 warranty wagner meters warrants this product against defects in material and work- manship for one (1) year from the date of purchase, subject to the following terms and conditions: wagner meters’ liability under this warranty shall be limited, at wagner meters’ option, to the repair or replaceme...
17 incidental or consequential damages for the breach of any express or implied warranty with respect to this product or its calibration. With proper care and maintenance, the meter should stay in calibration; however, because wagner meters has no control over the manner in which the unit will be us...
18 additional statements, whether oral or written, except written statements from an officer of wagner meters do not constitute warranties and should not be relied upon by the customer. This warranty is personal to the customer purchasing the product from wagner meters and is not transferable..
19 repair service in the event of damage, failure, or if the unit requires re-calibration, contact wagner meters technical services department at www.Wagnerrepairs.Com or by phone for complete shipping information. The values stored in memory may be lost in the event that the meter is sent in for re...
Wagner meters 326 pine grove road, rogue river, or 97537 usa phone: (541) 582-0541 fax: (541) 582-4138 e-mail: sales@wagnermeters.Com visit our moisture measuring information center at: www.Wagnermeters.Com © 2017 wm wagner meters part # 500-02200-001 rev. C.
