0517 • form no. 0520701a flexio ™ 2000 / 3000 owner‘s manual • manuel de l‘utilisateur • manual de usario read this manual for complete instructions • lire ce manuel pour obtenir des directives complÈtes • lea este manual para obtener las instrucciones completas wagner-group.Com en es f français - p...
2 en important safety information table of contents important safety information ........................................... 2-3 controls and functions ......................................................... 4-5 material preparation ....................................................................
En 3 important safety information safety hazards hazard: explosion or fire flammable vapors, such as solvent and paint vapors, in work area can ignite or explode. Prevention: • do not spray flammable or combustible materials near an open flame, pilot lights or sources of ignition such as hot objects...
4 en controls and functions ispray® nozzle x-boost™ turbine 3000 only 2-stage trigger spray width lever (for large projects) detail finish nozzle (for small projects) air cap 1.5 qt cup 2-speed x-boost™ power dial (2000) variable speed x-boost™ power dial (3000) material flow control filter housing ...
En 5 controls and functions + - + - + - + - 2000 3000 x-boost™ power dial the x-boost power dial adjusts the level of air power produced by the turbine. The flexio sprayer model 2000 is equipped with a 2-speed air power control (hi / lo). The flexio sprayer model 3000 is equipped with a variable spe...
Material preparation 1 2 3 6 en to prepare the material 1. Stir the spraying material thoroughly. 2. Unscrew the cup from the nozzle. 3. After the material has been properly thinned* and strained, fill the container to desired level. *thinning the material for certain spraying situations or desired ...
En 7 assembly 1 2 a b 3 4 5 assembly attention make sure the power cord is unplugged. 1. Insert the suction tube into the intake opening. 2. Align the pickup tube: a if spraying downward, the angled end of the pickup tube should be pointing toward the front of the nozzle. B if spraying upward, the a...
8 en power and material controls x-boost™ power dial the x-boost™ power dial adjusts the level of air pressure produced by the turbine. The x-boost™ power dial is factory-set at maximum out of the box. 2-speed air power control - the flexio model 2000 is equipped with a 2-speed air power control (hi...
En 9 spray pattern adjustment adjust spray shape adjust the spray pattern by turning the air cap ears. The air cap position will determine the movement direction of the spray gun. The positions of the air cap and the corresponding spray pattern shapes are illustrated below. Test each pattern and use...
10 en proper spraying technique stop the room you are spraying must be properly masked in order to prevent overspray from covering woodwork, floors or furnishings. Make sure you have properly masked the room per the instructions on the enclosed “taping guide”. I if spraying with an air-assisted spra...
En 11 proper spraying technique i use the images and guidelines below in order to assist you in achieving the desired spray pattern for your project. These are meant to be general starting points - you may have to slightly modify certain controls on the system in order to get the exact performance y...
12 en cleanup 1 1/2 pull 2 3 4 5 empty waste container 6 1/2 pull flushing the unit special cleanup instructions for use with flammable solvents (must have a flashpoint above 100ºf (38ºc): • always flush spray gun outside. • area must be free of flammable vapors. • cleaning area must be well-ventila...
En 13 cleanup (continued) cleaning the nozzle 1. Make sure power cord is unplugged. Push the tab below the trigger, twist and separate the nozzle from the turbine. Wipe the exterior of the cup and nozzle until clean. 2. Ispray nozzle only - a. Remove the air cap (a) by prying it off the connecting n...
14 en maintenance cleaning the filters attention before every use, you should inspect the air filters in the turbine to see if it is excessively dirty. If it is dirty, follow these steps to replace it. Never operate your unit without the air filters. Dirt could be sucked in and interfere with the fu...
En 15 troubleshooting problem cause solution problem a: little or no material flow 1. Nozzle clogged. 2. Suction tube clogged. 3. Air vent on suction tube blocked. 4. Material flow setting too low. 5. Suction tube loose. 6. No pressure build up in container. 7. Air valve tube not functioning. 8. Noz...
44 en f es parts list • liste de pièces • lista de piezas 1 3 2 4 x-boost™ turbine • turbine de x-boost™ • turbina de x-boost™ replacement parts available by calling customer service on peut obtenir des pièces de rechange en appelant le service à la clientèle. Los repuestos están disponibles llamana...
45 parts list • liste de pièces • lista de piezas es f en 1 2 3 4 5 6 7 # part no. Nº de piéce pieza no. English description français description español descripción qty. Qte. Cant. 1 0520006 spray gun assembly (includes items 1-7) ensemble de pistolet (inclut des pièces 1 à 10) ensamblaje de pistol...
46 en f es parts list • liste de pièces • lista de piezas # part no. Nº de piéce pieza no. English description français description español descripción qty. Qte. Cant. 1 0529276 nozzle assembly (includes items 1-9) ensemble de buse (inclut des pièces 1 à 9) ensamblaje de boquilla (incluye los articu...
47 limited warranty • garantie limitée • garantía limitada es f en hvlp paint spray equipment this product, manufactured by wagner spray tech corporation (wagner), is warranted against defects in material and work-manship for one year following date of purchase if operated in accordance with wagner’...
Flexio ™ 2000 / 3000 wagner-group.Com.