English français español 0215 • form no. 0529403c owner’s manual read this manual for complete instructions français (page 21) / español (página 41) contents 2 important safety information 4 controls and functions 5 overview 6 setup 7 preparing to spray 8 power and material controls 9 spray pattern ...
English 2 © wagner spray tech - all rights reserved important safety information read all safety information before operating the equipment. Save these instructions. Indicates a hazardous situation which, if not avoided, could result in death or serious injury. To reduce the risks of fire or explosi...
English © wagner spray tech - all rights reserved 3 important safety information warning - to reduce the risk of injury: 1. Always wear appropriate gloves, eye protection, clothing and a respirator or mask when painting. Hazardous vapors – paints, solvents, insecticides, and other materials can be h...
English 4 © wagner spray tech - all rights reserved controls and functions spray width lever x-boost™ power dial x-boost™ turbine on / off switch filter housing (both sides) suction tube holder / paint can attachment bracket fluid pump to turbine power cor d (14.5 f t) 2-stage trigger turbine power ...
English © wagner spray tech. - all rights reserved 5 overview note: follow the steps below to unpackage your sprayer and prepare the system. 1. Pull the suction tube (a) from the suction tube holder. Pull the yellow handle (b) away from the pump and unhook it. Pull it backwards over the pump to free...
English 6 © wagner spray tech. - all rights reserved setup before you begin never point the spray gun at any part of the body. Important: make sure the power cord is unplugged. Setup note: make sure the system is placed in a level, clean surface. Follow these instructions for both one-gallon and fiv...
English © wagner spray tech - all rights reserved 7 preparing to spray note: before spraying, you will need to prime the system (deliver material from the container to the spray nozzle via the paint hose). Follow the steps below. You will need: • waste bucket • drop cloths to protect floors and furn...
English 8 © wagner spray tech - all rights reserved power and material controls spray performance will depend upon a number of factors: material thickness, air power, spray pattern selected, and material flow. Testing different variations of the control settings will help you achieve the desired res...
English © wagner spray tech - all rights reserved 9 spray pattern adjustment adjust spray shape - both nozzles the spray pattern shape is adjusted by turning the adjustment ring to either the vertical or horizontal positions. The positions of the air cap and the corresponding spray pattern shapes ar...
English 10 © wagner spray tech - all rights reserved proper spraying technique stop the room you are spraying must be properly masked in order to prevent overspray from covering woodwork, floors or furnishings. Make sure you have properly masked the room per the instructions on the enclosed “taping ...
English © wagner spray tech - all rights reserved 11 proper spraying technique pattern examples use the images and guidelines below in order to assist you in achieving the desired spray pattern for your project. These are meant to be general starting points - you may have to slightly modify certain ...
English 12 © wagner spray tech - all rights reserved cleanup purging the paint hose before you begin important: make sure a drop cloth is placed underneath the pump and material container to catch any drips. Note: follow the cleanup steps in this manual if you used the direct feed ispray nozzle only...
English © wagner spray tech - all rights reserved 13 cleanup (continued) flushing the nozzle before you begin • if you sprayed using latex materials, you will need a 1- to 5-gallon container filled with warm, soapy water. • if you sprayed oil-based materials, you will need a bucket filled with appro...
English 14 © wagner spray tech. - all rights reserved cleanup (continued) cleaning the regulator note: removing and cleaning the regulator is necessary to keep your sprayer from clogging or from producing an irregular spray pattern. To clean the regulator 1. Remove the paint hose (a) from the nozzle...
English © wagner spray tech. - all rights reserved 15 cleanup (continued) cleaning the nozzle to clean the nozzle 1. Remove the adjustment ring (a) carefully from the connecting nut (b). Loosen the connecting nut. 2. Remove the parts as shown. The nozzle seal (c) may become stuck inside the ispray n...
English 16 © wagner spray tech - all rights reserved maintenance cleaning the filters important: before every use, you should inspect the air filters in the turbine to see if it is excessively dirty. If it is dirty, follow these steps to replace it. Important: never operate your unit withouttheairfi...
English © wagner spray tech. - all rights reserved 17 troubleshooting problem cause solution problem a: little or no material flow both nozzles 1. Nozzle clogged. 2. Material flow setting too low. 3. Air filter clogged. 4. Spray material too thick. 1. Clean. 2. Increase material flow setting. 3. Cha...
English 18 © wagner spray tech. - all rights reserved control finish nozzle setup note: follow the steps below in order to set up the sprayer for use with the control finish nozzle. 1. Unplug the turbine power cord from the pump cord. Push the tab below the trigger, twist and separate the nozzle fro...
English © wagner spray tech. - all rights reserved 19 cleanup (control finish nozzle only) flushing the unit before you begin: when cleaning, use the appropriate cleaning solution (warm, soapy water for latex materials; mineral spirits for oil-based materials) important: never clean air cap or air h...
English 20 © wagner spray tech. - all rights reserved cleanup - continued (control finish nozzle only) cleaning the nozzle 1. Make sure power cord is unplugged. Push the tab below the trigger, twist and separate the nozzle from the turbine. Wipe the exterior of the cup and nozzle until clean. 2. Uns...
English © wagner spray tech. - all rights reserved 61 parts list • liste de pièces • lista de piezas english français español 1 3 2 4 # part no. Nº de piéce pieza no. English description français description español descripción qty. Qte. Cant. 1 --------- x-boost turbine (includes items 2-4) turbine...
Español français english 62 © wagner spray tech - all rights reserved parts list • liste de pièces • lista de piezas 1 2 3 4 5 6 7 8 # part no. Nº de piéce pieza no. English description français description español descripción qty. Qte. Cant. 1 0529437 spray gun assembly (includes items 1-7) ensembl...
English français español © wagner spray tech - all rights reserved 63 parts list • liste de pièces • lista de piezas 1 2 3 4 5 9 7 8 # part no. Nº de piéce pieza no. English description français description español descripción qty. Qte. Cant. 1 0417233 control finish nozzle assembly (includes items ...
Español français english 64 © wagner spray tech - all rights reserved accessories • accessoires • accesorios part no. Nº de piéce pieza no. English description français description español descripción 0529014 ispray nozzle assembly ensemble de buse de ispray ensamblaje del boquilla de ispray 0529013...
English français español © wagner spray tech - all rights reserved 65 notes • remarques • notas manufacturing code location • emplacement du code de fabrication • ubicación del código de fábrica this unit contains no servicable electricalparts.Donotattemptto service yourself. Store indoors with the ...
Français 66 © wagner spray tech - tous droits réservés garantie limitée pulvérisateur de peinture hvlp cet article fabriqué par wagner spray tech corporation (wagner) est garanti contre tout défaut de fabrication et de matériaux pour une période d’un an suivant la date d’achat, à condition qu’il soi...
© wagner spray tech - reservados todos los derechos 67 español garantía limitada equipo de atomización de pintura hvlp este producto, fabricado por la wagner spray tech corporation (wagner), está garantizado contra defectos de materiales y de mano de obra por un año a partir de la fecha de compra si...
English 68 © wagner spray tech. - all rights reserved limited warranty hvlp paint spray equipment this product, manufactured by wagner spray tech corporation (wagner), is warranted against defects in material and work-manship for one year following date of purchase if operated in accordance with wag...