Wahl TRIPLE PLAY Operating Instructions

4

3

2

5

6

7

8

15

16

10

11

9

14

12

13

SPECIAL FEATURES:

 Rotary Shaver Attachment Head 

Your shaver has been designed with several advanced 

features to help you get perfect 

results every time you groom. 

Your shaver head detaches and 

can be replaced by several other 

grooming tools to achieve your no 

compromise look.

• To remove shaver head, 

pull the head in a downward 

fashion and away from switch.

•  To re-attach, position head 

as shown.  Locate small tab 

and hook onto back (1) then 

rock forward until it snaps 

down (2).  Before using, make sure 

the head is fully attached with no gaps 

between the shaver head and shaver body 

as shown in the shaded area (3).

• Open shaver head LID to remove or clean unwanted hair from 

chambers.  Simply pull up the razor foil lid as shown below.  To 

re-attach it, align 

pegs from razor LID 

with guide holes 

on Shaver base 

attachment shown 

below right.

NECKLINES AND SIDEBURNS 

USING TRIMMER HEAD 

Detach shaver head as described earlier.  

Attach trimmer blade as described earlier. 

Slowly move trimmer downward on 

desired areas to neatly trim and shape.

TRIMMING AND EDGING YOUR FACIAL HAIR

The following are suggested trimming steps and trimmer positions. 

You may find different procedures work 

better for you.

1.  Comb your beard in the direction that 

it grows to help reveal stray hairs that 

may be longer than the others.

2.  Attach the 6-position trimming guide 

to trim and taper your beard. Begin 

with the guide set at a long trimming 

length.  Trim toward your chin in 

smooth, overlapping strokes, following 

the lay of your beard. If you trim 

against the way your beard naturally 

lays, the trimmer will cut the hair much shorter and the result 

may be patchy. 

Adjust the trimming guide to progressively shorter settings until 

you reach the desired length of beard. You may wish to set the 

trimming guide attachment to cut closer near the ear and down 

under the chin, changing to a longer setting toward the front 

of the face and point of your chin. When the trimming guide is 

removed, it will remain at its last length setting until you change it.

Always be sure the trimming guide is 

locked solidly into the desired position 

before you start to trim.

3.  To cut the outline of your beard, 

remove the trimming guide. Starting 

under your chin and working back 

toward your jawbone and ears, cut the 

 A 6-Position Trimming Guide makes 

achieving a consistent trim easy every time.  

The guide can be removed (providing a 

seventh cutting position) and reattached 

without changing the preset cutting length, 

so once you have found the perfect length, 

there’s no guesswork in achieving it every trim. 

The trimming guide is a two-piece assembly, 

consisting of a base and a comb. It should 

not be disassembled. To attach the guide, 

simply slide it on at a slight angle and press 

the release tab down to secure in position. 

To remove the guide, gently push up on the 

release tab and slide the assembly away from 

the trimmer. Adjust the trimming length by 

pressing on the thumb lever and moving the 

comb forward or backward to the desired 

setting. 

A Rotating Head. The trimming head rotates 180 degrees, 

providing two trimming positions. This allows you to achieve the 

optimum ergonomic relationship between the hand, the trimmer 

and the face. Rotate the head 

to the desired position as 

follows. With the switch in the 

“OFF - 0”  position, depress the 

lock button and rotate the head 

clockwise or counterclockwise 180 degrees.

DO NOT ROTATE HEAD DURING USE WITH SHAVER 

ATTACHMENT.

CAUTION: 

Do not insert the detailer or any other foreign object into 

the inner ear. For hair growing on the outside of the ear, simply move the 

detailer slowly along the edges of the ear.

TRIMMING EYEBROwS wITH HAIR COMB 

Snap on eyebrow guide comb on detailer as shown.  

Slowly move detailer to neatly trim stray hairs. Do 

not press hard against brow as it may remove too 

much hair.

You may also use your trimmer blade with the #2 or 

#3 guide combs.  Move the trimmer with the direction of the hair flow (from 

the bridge of your nose to the temple). Be sure to mind your eyelashes as 

you trim.

TRIMMING ARM & LEG HAIR USING TRIMMER 

HEAD. 

Simply glide the trimmer over your arm or leg until desired hair length is 

achieved. The first time you trim the hair, start by using a longer setting on 

the guide comb on the trimmer, then use progressively shorter settings if a 

shorter length is preferred.

TRIMMING CHEST & STOMACH USING TRIMMER 

HEAD. 

Glide the trimmer over your torso region, in an upward motion until desired 

hair length is achieved. For tight, scratch-free trimming, use the #1 guide 

comb.

TRIMMING PRIVATE AREAS wITH THE TRIMMER 

& DETAILER HEAD.

1. Volume reduction using trimmer head. Attach guide comb and select a 

long trimming length. Begin trimming, starting at the top and working 

down. Use progressively closer settings to get the “look” and length you 

prefer.

2. For hard to reach or tight areas, use the detailer head. Always pull skin 

taut. Then slowly move the detailer through area to trim until desired look 

is accomplished.

3. Shave in your private areas by gently shaving in the desired area and 

always keep the skin taut.

outer perimeter of your beard underneath the jawbone. Continue 

the line all the way up to the ears and hairline.

4.  Accentuate your beard line by using the trimmer in a downward 

motion. Start at the line you’ve created and, working from the chin 

back toward the ears, trim the area right under your beard line. 

5.  Define the upper part of your beard 

using the same technique.

6.  For a neater finished look, replace 

attachment blade to the detail blade 

forward. Use this blade for fine, detail 

trimming anywhere it is needed, such 

as at the sideburns near the ears, goatees, etc.

USING GUIDE COMBS: 

To attach guide combs, hold comb with the teeth up.  

Snap guide comb attachment firmly to the bottom of 

the trimmer blade.

TRIMMER GUIDE COMBS:

TRIMMING wITH GUIDE COMBS: 

The stubble guide has 1 bar, the medium-cut attachment has two bars and 

the long-cut attachment has three bars. These attachments are ideal for 

blending, tapering and defining beards, as well as for achieving a “close 

trim” stubble look around the face. To use the attachments, go with the hair 

direction.  To achieve closer looks, go against the hair direction.

TRIMMING NOSE HAIR 

Make sure the nasal passages are clean. Slowly move the detailer in and 

out of each nostril, no more than 1/4-inch deep. 

TRIMMING EAR HAIR 

Make sure the outer areas of the ears do not contain any wax. Hold the ear 

flat with one hand and carefully insert detailer no more than 1/4-inch into 

the outer ear.  

• Never clean, remove or replace attachment head assembly while 

motor is on.

• Do not apply pressure to blade foils.  Do not touch razor heads 

with hard objects as this may dent or damage precision-made 

slotted blade foils.

• Do not use razor if blade foils are damaged or broken.

• The Rotary Shaver may be opened up to simply discharge 

whiskers.

• Do not immerse razor unit in water.

• Only get the shaver lid wet and NOT the shaver base 

as shown in illustration at right.  Water may get into the 

base and become trapped.  Only brush or blow out the 

base if any whiskers remain.

• The quickest and easiest way to clean the razor heads 

is 

to rinse them after each use or at least once a week with water:  

Water from the tap should be on a cold setting.

1. Always switch razor OFF, unplug and remove power cord 

before cleaning.

2. Before cleaning under tap water, first remove the rotary shaver 

attachment head from body as described earlier.

3. Pop open top razor foil from attachment head described earlier.

4. Clean inside and outside the razor heads and hair chamber by 

running under cold water.

5. Leave razor head assembly open to air dry before next use.

NOTE: Do not wipe or dry the shaving heads with a towel or 

tissue.  This could damage the shaving heads.

6. If the shaving assembly unit becomes detached from the 

shaver base, align pegs from razor LID with guide holes on shaver 

base attachment.

7. You may also clean the hair chamber without water by using 

the supplied cleaning brush.

IMPORTANT SAFEGUARDS

When using your electrical appliance, basic 

precautions should always be followed, 

including the following:

READ ALL INSTRUCTIONS AND SAFEGUARDS 

BEFORE USING THIS TRIMMER.

DANGER

To reduce the risk of death or injury by 

electric shock:

1. Do not reach for an appliance that has 

fallen into water. Unplug immediately from 

the outlet. 

2. Do not use while bathing or in a shower.

3. Do not place or store appliance where it 

can fall or be pulled into a tub or sink. Do 

not place in or drop into water or other 

liquid.

4. Except when charging, always unplug 

this appliance from the electrical outlet 

immediately after using.

5. Always unplug this appliance before 

cleaning. 

6. (Rechargeable unit only.) Unplug the 

charger before using trimmer. 

7.  Insert only recharging transformer plug supplied by the 

manufacturer  into charger receptacle.

TROUBLESHOOTING

If your Trimmer does not seem to take a charge, check the following 

before returning it for repair:

1.  Check outlet to make sure it is working by plugging in another 

appliance.

2.  Make sure the outlet simply is not connected to a light switch which 

turns the power at the outlet off when lights are turned off.

3.  Be sure the trimmer is properly connected to the recharging 

transformer, all connections are secure and the switch on the 

trimmer is turned “OFF - 0.”

4.  If your electricity is connected to a master power switch, we 

suggest the trimmer be disconnected from the charger anytime 

the master switch is off. Leaving the unit plugged into a dead 

outlet or an unplugged charger will drain the battery.

5.  If trimmer does not run and it is completely charged, turn the unit 

“ON - I” and pinch or push the blades manually. (Oil may have 

dried out between the blades, so they may be temporarily stuck 

together.)

LITHIUM-ION  

BATTERY DISPOSAL

Do not attempt to remove the battery from unit.  Lithium-Ion 

batteries can explode, catch fire, and/or cause burns if disassembled, 

damaged, or exposed to water or high temperatures.  Do not attempt 

to remove the battery for disposal.   Lithium-Ion batteries may 

be subject to local disposal regulations.  Many locations prohibit 

disposal in standard waste receptacles. Check your local laws and 

regulations.  For recycling contact a government recycling agency, 

waste disposal service, retailer, or visit online recycling sources, such 

as www.batteryrecycling.com or www.rbrc.org.

8. Never drop or insert any object into any 

opening.

9. Do not use this appliance with a damaged 

or broken blade or trimming attachment, as 

facial injury may occur. 

10. Always attach plug to appliance first, then 

to outlet. 

To disconnect, turn unit “OFF - 0,” 

then remove plug from outlet.

SAVE THESE INSTRUCTIONS

For Household Use Only

RECHARGING

1.  This trimmer is conveniently designed for household use. It 

should be allowed to charge 1 hour before first use.

2.  Remove the trimmer, recharging transformer and accessories 

from the packing material.

3.  Connect the transformer to the trimmer. BE SURE TRIMMER IS 

IN THE “OFF - 0” POSITION WHEN CHARGING. 

4.  Plug the recharging transformer into any convenient electrical 

outlet at the correct voltage.

5.  When trimmer is low in power, it should be connected to the 

transformer and plugged into an outlet to assure maximum 

power is available when it is next used. This transformer  

is designed to completely charge the battery without 

overcharging.  Do not use the trimmer while it is charging.

6.  The battery will take approximately 60 minutes to charge.  The 

Lithium Ion Trimmer also has quick charge capability.

wARNING

To reduce the risk of burns, electrical shock or 

injury to persons:

1. Do  Not  Crush,  Disassemble,  Heat  Above 

100°C  (212°F),  or  Incinerate  the  appliance, 

due to Risk of Fire, Explosion, or Burns.

2. This power unit is intended to be correctly 

orientated in a vertical or floor mount position.

3. Close supervision is necessary when this 

appliance is used by, on, or near children or 

disabled persons.

4. Use this appliance only for its intended 

use as described in this manual. Do not 

use attachments not recommended by the 

manufacturer.

5. Never operate this appliance if it has a 

damaged cord or plug, if it is not working 

properly, if it has been dropped or damaged, 

or if it has been dropped into water. Return 

the appliance to Wahl Clipper Corporation for 

examination and repair.

6. Keep the cord away from heated surfaces.

7. Do not use outdoors or operate where 

aerosol (spray) products are being used or 

where oxygen is being administered.

Lithium•Ion

Triple Play

ROTARY SHAVER USE 

For New Rotary Shaver User

• Use your new razor exclusively for 3 

weeks to fully enjoy the closeness of a 

Wahl shave.

• At first you may not get as close a shave as you 

expect, or your face may even become slightly 

irritated.  This is normal since your beard and skin 

will need time to adjust.  Invest 3 weeks and you’ll 

soon experience the full joy of your new razor.

• If you are still not convinced after 21 days, Wahl 

will refund you the full purchase price as long as 

the request is received within 30 days of purchase 

accompanied with original receipt.

How to shave with an electronic razor

• Use this razor for its intended household use as described in 

this manual.

• DO NOT ROTATE HEAD WITH SHAVER HEAD ATTACHED.  ONLY 

USE SHAVER WITH HEAD POSITIONED ON BODY UNIT AS 

SHOWN IN ILLUSTRATION ABOVE OR DAMAGE MAY OCCUR.

• Shaving with a clean, dry face gives the best results.

1. Turn razor ON with the on/off button.  Shave against the 

direction of the beard growth using both straight and circular 

movements.

2. Stretch your skin taut with your free hand so blades can more 

clearly cut whiskers.  Gently press razor to skin so the floating 

heads can follow the contours of your face.  DO NOT press too 

hard as hair does not feed as well.  Too much pressure can 

pinch the skin into the blades.

3. Turn razor OFF with the on/off switch.

Cleaning Rotary Shaver 

(Attachment Head Only)

• Regular cleaning guarantees better shaving results.

 A Detachable blade system enables you to quickly change 

from a shaver to a precision trimmer to trim mustache, goatee, 

or anywhere.  To remove attachment, simply 

pull top edge of blade away from body unit. To 

attach, align back tab of attachment head to 

cavity on the inner edge of trimmer unit and 

push down on top of blade.

Should blades become damaged or dull or if 

you want additional attachment heads for your 

trimmer, you may purchase them from Wahl. 

Be sure to ask for the following attachment with part number 

from our service and repair department (see last page for contact 

information):

Attachment Head: Wahl Part Number

Trimmer: #59300 Included 

Detailer: #59301 Included 

T-Blade: #59302 

Rotary: #58067 

  Dual Shaver:  #59303 

  Rotary Shaver:  #07018  Included 

www.wahlshavers.com

The trimmer you purchased may not have all of these heads, but 

they will all work with your trimmer if you wish to purchase them.

Operating Instructions for the 

Lithium Ion Grooming Kits

Instrucciones de operación 

de la recortadora recargable

No Compromise Shaver/Trimmer/Detailer

Afeitadora/Desbastadora/Pulidora

www.wahlshavers.com

SERVICE AND REPAIR

If you have problems with your trimmer, send complete unit 

prepaid with a note explaining the problem to:

Wahl Clipper Corporation       

Attn: Repair Department 

3001 Locust Street 

Sterling, IL 61081 

Telephone (800) 767-9245

For products purchased outside the United States, contact  your distributor.

If for any reason within 30 days of purchase of your Wahl® 

trimmer you are not satisfied with your trimmer and would 

like a refund, just return your trimmer, together with the sales 

receipt, to the retailer from whom you purchased it.  Wahl will 

reimburse all retailers who accept trimmers within 30 days of 

purchase.  If you have any questions regarding this money-

back guarantee, please call 1-800-767-9245 in the United 

States.

30 Day Money Back Guarantee!

© 2011 Wahl Clipper Corporation 

Part No. 94596 

Printed in U.S.A.

For more information or Product Registration, visit 

www.wahlshavers.com

5-YEAR LIMITED wARRANTY

Valid in U.S.A. Only

If your Wahl product fails to operate satisfactorily within five 

(5) years from the date of original purchase or receipt as a gift, 

Wahl will, at our option, repair or replace it and return it to you 

FREE OF CHARGE. Do not return this product to store where 

purchased. Products needing repair under this warranty should 

be returned with postage prepaid to:

wahl Clipper Corp.

Attn: Repair Department

3001 Locust Street

Sterling, Illinois 61081

Include a note describing the defect and the date of original 

purchase or receipt as a gift (if in warranty). Products out of 

warranty will be repaired at our standard repair charges.

This warranty is void and no repair or replacement will be made 

under this warranty or otherwise if: (1) The product is modified 

in any manner or repaired by anyone other than Wahl Clipper 

Corporation or Wahl authorized service center. (2) The product 

has been used commercially or subjected to unreasonable use.

This warranty gives you specific legal rights and you may 

also have other rights which may vary from state to state. No 

other written express warranty is given. Any implied warranty, 

including any warranty of merchantability which may arise from 

purchase or use, is limited to the year period provided in this 

express warranty. Some states may not allow such limitation, 

so it may not apply to you. No responsibility is assumed for 

incidental or consequential damages of any type, or for the use 

of unauthorized attachments. Some states may not allow the 

exclusion or limitation of incidental or consequential damages, so 

the limitation or exclusion may not apply to you. Outside U.S.A., 

check with store for Wahl authorized distributor’s warranty.

#1  Stubble Length   (2 mm)

#2  Short  

(4 mm)

#3  Medium Short   (6 mm)

#4  Medium  

(8 mm)

#5  Medium Long   (10 mm)

#6  Long  

(12 mm)

 Stubble 

Medium 

Full 

#07018

#59300 #59301 #59302 #58067 #59303

REPLACEMENT LID wITH FOIL  

It’s recommended that the rotary 

foil lid should be replaced at 

least once a year for optimum 

closeness.  Should the foils 

become damaged or dull or if 

you want additional foils for long 

trips, you may purchase just the LID 

with foils from Wahl.  Be sure to ask for the 

following attachment with part number 07021 from our service 

and repair department or online at:

www.wahl-store.com/products/accessories/shaver

Note: Additional LID with 

foils may be ordered 

located on the last page.

Lock Button

OILING BLADES

For best results, put one or two drops of Wahl Clipper Oil on  

the blades only when necessary, or approximately once a month. 

Motor bearings are permanently lubricated—do not attempt to oil. 

When oiling your trimmer, turn the trimmer “ON - I,” hold the unit 

with the blades facing DOWN and squeeze one or two drops of oil 

onto the blades. Wipe off excess oil with soft cloth. 

NOTICE—DO NOT OVER OIL! 

Excessive oiling or application of liquids will cause damage if 

allowed to seep back into motor. 

BLADE CARE

Trimmer blades have precision-hardened, ground and lapped 

cutting teeth. Blades should be handled carefully and never bumped 

or used to cut dirty or abrasive material. Never rinse the blades with 

water, or the blades may rust. Clean with the included brush.

CLEANING/STORAGE

Before storing your trimmer, use the cleaning brush to whisk 

any loose hairs from the unit and the blades. Store unit in such a 

manner so that blades are protected from damage.

When the trimmer is not in use, the trimmer guide/blade guard 

attachment should be in place to protect the blades.

Store rotary shaver with included head cover.

This appliance should be stored in a manner where it is not 

subjected to Crushing, Heating above 100°C (212°F), or 

Incineration.