Walimex Pro 360 TTL Instruction Manual - page 28
54
55
• Check that it is working. To do this, press the master test button .
The slave flash will then be triggered. If the flash is not triggered, change
the angle to the master flash and change the distance to the master flash.
Nikon:
• Set the Light Shooter 360TTL/N to camera and switch to master (wireless).
You can set the mode to M/A/B/C individually.
• Set the second Light Shooter 360TTL/N camera flash to slave (wireless).
The slave can be allocated to group A/B/C.
• Make sure both are set to the same channel.
• Place the camera and flashes as per the above illustration
• Check that the master flash is ready. The light must be on. As soon as the
slave flash is ready, the light will flash at 1 second intervals.
• Check that it is working. To do this, press the master test button . The
slave flash will then be triggered. If the flash is not triggered, change the
angle to the master flash and change the distance to the master flash.
If the flash does not work or triggers on its own, this could be because of lit
computer screens nearby or the light from fluorescent tubes.
- 17 -
- 18 -
无线闪光拍摄:光学传输
检查传输频道。
3
● 将主控单元和从属单元的频
道设为一致。(第1 页)
6
定位相机和闪光灯。
4
● 将其定位在(第15页)所示的
范围内。
检查闪光灯是否准备就绪。
5
● 检查主控闪光灯就绪指示灯
点亮。
● 当从属闪光灯就绪时,自动
对焦辅助光发光区域以1秒间
隔闪烁。
4 i-TTL: 全自动无线闪光拍摄
、
使用一个从属单元的自动闪光拍摄
设置主控单元。
1
● 将安装在相机上的AD360II-N
设为主控单元。(第15页)
● M/A/B/C都可独立设置为
TTL。
检查操作。
6
● 按下主控闪光灯的试闪按钮
。
● 从属单元闪光。如果从属单
元不闪光,检查是否将其放
置在操作范围内。
无线闪光拍摄:光学传输
设置从属单元。
2
● 将要被无线控制AD360II-N
设为从属单元。(第15页)
● 可以选择
。
A/B/C
如果从属单元附近有荧光灯或电脑显示器,这些光源的存在可能会导致从属单元发生故障,并导致其意外闪光。
●
间,无法进行测试闪光。
● 可以进行设置以使自动对焦辅助发射器在从属单元回电完毕时不闪烁(C.Fn-AF/第23页)。
如果从属单元的自动关闭电源生效,按主控单元的测试闪光按钮打开从属单元。请注意在相机的测光定时工作期
在主控单元上设定的闪光曝光补偿和其他设置也会在从属单元中自动设定。不需要操作从属单元。可按照与普通闪光
拍摄相同的方法使用以下设置进行无线闪光拍摄。
● 闪光曝光补偿( /第 页)
10
● 高速同步( /第 页)
11
SYNC
可以使用两个或两个以上主控单元。通过准备多台装有主控单元的相机,可以在保持相同照明(从属单元)期间更换相
机进行拍摄。
使用全自动无线闪光
关于主控单元
6 RPT:
、
手动无线闪光拍摄
设定
1
● 按下
MODE
>模式选择按钮
令屏幕显示
RPT
>。
● 设定频闪闪光设置。(第14页)
5 M:
、
手动无线闪光拍摄
使用手动闪光的无线(多重闪光)拍摄,可以为每个从属单元(闪光组)设定不同的闪光输出进行拍摄。在主控单元上设定所有参数。
将闪光模式设为
。
1
● 按下功能按钮4选
择组别,再按功能按钮3
设定为M模式。
M>
拍摄照片。
3
● 各组以设定的闪光光比闪光。
MODE
设置闪光输出。
2
● 在选择组别状态下,按功能按
钮2
选择功率设定,
旋转调节旋钮为闪光组设定闪光
输出,并按
SET
设置按钮确
定。
>
>
可以在1Hz
至
100Hz
之间设定光学无线传输拍摄期间的频闪闪光的闪光频率。
Canon:
•
Press function button 4 until
• Then press function button 1 until
adjusting wheel to select one of the 32 channels.
• Confirm the choice with the
Nikon:
• Press function button 3.
• Choose from channel 1 to 4.
• Confirm the choice with the
- 15 -
- 16 -
2、设置主控单元的闪光模式
在禁用主控单元闪光模式下,只有从属单元的闪光灯闪光。
按功能按钮4 选择
1
M/A/B/C
组别,再按功能按
钮3选择主控单
元的闪光模式可以在
OFF/i-
TTL/M
之间进行切换,选择
其中一种作为主控单元的闪
光模式。
3、设置通讯频道
如果在拍摄现场不止一个无线闪光系统,您可以通过更改通讯频道来防止信号干扰。保证主控单元和从属单元设置为
相同的频道编号即可。
按下功能按钮
3,旋
1
转调节旋钮从
1至4中选择频
道。
按下
SET
>设置按钮确定。
2
按“
MODE/
锁定”按钮可切换
2
至
RPT
模式。
无线闪光拍摄:光学传输
●
●
●
通过此款产品,支持创建三个从属单元组,并实现
i-TTL
自动闪光。您可以通过
i-TTL
自动闪光轻松获取多种照明效
果。
使用主控单元按组分别设置的任何
i-TTL
自动闪光,手动闪光和频闪闪光设置都会被自动传输到从属单元。因此,在
拍摄时无需操作从属单元。只需在主控单元上对每个从属组进行单独设置就可完成。
将此产品设置为主控单元时,可以在
i-TTL/M/RPT/OFF
四种闪光模式下工作。
主控单元/从属单元设置位置和范围
1
您可以在普通闪光和无线闪光之间切换。对于普通闪光,请务必将无线设置设为“关”。
、无线设置
室内
室外
15
49 2
米( . 英尺)
10
32 8
米( . 英尺)
80°
8
26 2
米( . 英尺)
12
39 4
米( . 英尺)
无线闪光拍摄:光学传输
●
●
即使有多个从属单元,主控单元也可通过无线控制所有的闪光灯。
本说明手册中,“主控单元”指安装在相机上的闪光灯,“从属单元”指通过无线控制的闪光灯。
按下无线设置按钮,令屏幕显
示和
>。
此时背光显示绿色。
RPT
主控单元设置
按下无线设置按钮,令屏幕显
示和。
此时背光显示橙色。
从属单元设置
该产品支持尼康创意闪光系统(CLS),具备无线闪光功能,具有主控闪光和从属闪光功能。作为主控单元,可以控制
并引闪SB-900、SB-910等尼康闪光灯。作为从属单元,受控SB-900、SB-910闪光灯无线信号和D7100/D7000/
D800等相机内闪指令,从而实现无线闪光。
CH
MODE
6.6.2 Fully automatic trigger in TTL mode
Canon:
• Set the Light Shooter to camera and switch to master (wireless).
• Switch the other camera flash to slave (wireless).
• Make sure both are set to the same channel.
• Place the camera and flashes as per the above illustration.
• Set the master flash to
set to
• Check that the master flash is ready. The light must be on. As soon as the
slave flash is ready, the light will flash at 1 second intervals.